Love my Outlaw, thanks for taking the time to share this video with us
@juliocruz7481
3 жыл бұрын
Thanks for the video!! I’ll prob add one myself for my wiring also!
@summertonfishing119
3 жыл бұрын
Awsome!!! Thanks for watching
@davidsmith-ri3fi
2 жыл бұрын
I just bough an Outlaw and love it . Wanting hatches but worried about leaking . I want to add 2 gear tracks 2 the rear where the flat area is for like a motor . Don't think i want a motor but the tracks would allow me to add or swith to anything . Also added noodles to my seat incase it comes off . Know a guy who rolled and lost his seat . I want lights for incase also . Just finished 9 miles from dillards ferry to rush on the buffalo river in Arkansas ... love my boat . I weigh 320 plus gear .
@summertonfishing119
2 жыл бұрын
The outlaw is great I love mine,it's a bit of a pain in the wind but overall a great kayak.if you plane on doing rails on the back I would recommend putting aluminium backing plates in the hull to mount through for added strength 💪👍
@leesuschrist
2 жыл бұрын
Good thought on keeping the scraps for weld repairs later. My dumb ass definitely would have thrown them out and thought of that later haha.
@summertonfishing119
2 жыл бұрын
Hahaha ya you never know if you could use them.thanks for the support
@dadinthecityoutdoors
3 жыл бұрын
Good job 👍🏼
@summertonfishing119
3 жыл бұрын
Thanks for watching
@dadinthecityoutdoors
3 жыл бұрын
@@summertonfishing119 where are you located? I am in MN.
@summertonfishing119
3 жыл бұрын
Im in northern ontario
@dadinthecityoutdoors
3 жыл бұрын
@@summertonfishing119 I hear that there is good fishing. Keep on yaking.
@vmexplorer
Жыл бұрын
Thanks for the video and the tips. How has this particular hatch been working for you? Any Leaks? Also, what is the specific product or model hatch plate that you installed? Did you install the same model hatch plate in all three locations? Many Thanks!
@summertonfishing119
Жыл бұрын
The hatches have worked well I never did get around to do the third one yet.the only time I've had a little bit of water go in was a really rough day on the water during a tournament were the bow went completely underwater quit a few times but it wasn't much.as for the model it was just a generic one off of Amazon for $17can
@johnnyb6566
Жыл бұрын
@@summertonfishing119 pic of your anchor trolley set-up?
@brettlynch9427
2 жыл бұрын
Do you think the trigrip rivets made for kayaks would work as well as the screws?
@summertonfishing119
2 жыл бұрын
Absolutely they would more than likely work better. Just don't forget the silicone
@Rhymeswithlaughter
2 жыл бұрын
Did the 6in work in the back?? I'm about to put a hatch in the back to install a Scotty anchor lock system...and a trolling motor mount later down the road.
@summertonfishing119
2 жыл бұрын
Unfortunately no I ended up putting it in my mother in law's kayak. I probably could have made it work but I'd rather go with the manufacturer's size
@Rhymeswithlaughter
2 жыл бұрын
I ended up installing the 5in in both the front and back and it works great! I am worried though about installing a hatch in the middle standing area. Does your outlaw give or bend more under your weight after installing the hatch or no change?
@Line7Charlie
2 жыл бұрын
Sorry for the stupid question but you mentioned you would need a hole saw that’s 5 1/2”. Wouldn’t you need a 5” if it’s a 5” hatch? Great video btw. Thanks for taking time to show how to correctly do the install.
@summertonfishing119
2 жыл бұрын
No the interior dimension of the hatch is 5"(were the cap comes out) but to install the hatch the outer dimension is 5 and a 1/2
@summertonfishing119
2 жыл бұрын
Not a silly question at all.Ands thanks for watching
@p374376
10 ай бұрын
Where did you get the hatch? Can't find a 5.5
@justinlogue31
2 жыл бұрын
What is the rope pulley system on the side of yours for?
@summertonfishing119
2 жыл бұрын
That would be my ancor trolly helps position were your ancor is dependent on wind or current
@justinlogue31
2 жыл бұрын
@@summertonfishing119 oh ok, thanks
@bjcantrell0131
3 жыл бұрын
What hatch did you buy?
@summertonfishing119
3 жыл бұрын
It was a private seller on Amazon $17.99 Canadian per hatch
@summertonfishing119
3 жыл бұрын
Pactrade marine
@jlansdale536
2 жыл бұрын
Have you evrr used tha OSI QUAD?
@summertonfishing119
2 жыл бұрын
I definitely know of it but i havnt tried it myself
@jlansdale536
2 жыл бұрын
Its a thousand times better than dap silicone. I used to install windows and thats all i used. It will never come off once cured.
@summertonfishing119
2 жыл бұрын
Good to know. Thanks for the tip. I'll certainly try it out...I have some other plans for the yak it will come in handy
@manbunfishing1249
2 жыл бұрын
The hatch worked great in my outlaw, thanks! I love this kayak! Check out this alternative to the overly expensive perception saddle bags! kzitem.info/news/bejne/yZmcqaKkaZ5qaaw
@summertonfishing119
2 жыл бұрын
Absolutely love it ..... I will certainly be looking Into those bags!!
@manbunfishing1249
2 жыл бұрын
@@summertonfishing119 crazy thing is I already had this bag for electric guitar accessories... Just saw it and wondered if it would fit. Who knew!?!
Пікірлер: 37