guys, I wouldn't even earn a living doing such a job 😂😂😂
@RoofingAmerica
4 жыл бұрын
That would leak really badly
@dodo14041980
5 жыл бұрын
This is 6 or 7 videos I watch and can not believe how much you in the US are complicating around the chimneys
@eastside0434
Жыл бұрын
I hope.it never rains with these installation issues,very poor quality materials and a hack job.
@markpyles9731
5 жыл бұрын
This is allot of extra work. I guess I will call Edco.
@ruthdanielson919
Жыл бұрын
Just installed a new roof and totally confused why roofers shingled over the apron flashing on the chimney and thinking maybe they used something like this, but so stupid how they flashed the wall flashing (L flashing under torch down) with the shed wall connection failing code inspection, worried they buried the base flashing under the shingles too but inspector not trying to find out if they screwed up or not.
@eastside0434
Жыл бұрын
Obviously they did not know what they were doing,this aluminum roof in this video is pure garbadge.
@kansascityshuffle8526
2 жыл бұрын
Brutal $30K roof and that’s the best system you can come up with?
@crushsmith7534
6 жыл бұрын
lol this has to be one of the worse metal roofs i have seen. followed by this horrid attempt at flashing a chimney, here is a hint if a pop can is thicker then your roof tin look else were.
@redsresearch
9 ай бұрын
where are you guys from?
@eddiegreg7064
5 жыл бұрын
Why isn't that chimney ice and watered? Thanks 🙈🙉 🙊
@masterzaga44
5 жыл бұрын
Edward Gregorczyk i think is just a Model. Not real roof. I guess in a real world you install wipe 300 around the chimney
@faithfulpatriot4008
5 жыл бұрын
I heard a crackhead slid down this roof and peeled all the tin off at the same time and when he went to the recycling plant to weigh it, they told him, he owes them $47.50. Boy was he mad! LMAO
@franciscoalmazan4409
3 жыл бұрын
I'm not a roofer and I think I could do a better job🤣
@kevincarpenter8141
6 жыл бұрын
Where do you buy this shingle kits or Roofing kits
@ABen-0107
3 жыл бұрын
👍 Good Video
@traceyjscott069
7 жыл бұрын
RIDICULOUS! Any guy with half a brain will bend the shingles up the front and sides. Fasten and caulk. Cover flash that. Caulk again. Then put a back flash on. And caulk that. Simple! They show you this way to get you to buy more flashing metals.
@eddiegreg7064
5 жыл бұрын
I'm not a fan of relying on caulk, I always cut a reglet and rely on my metal work, of course I clean it up with a nice thin bead. Thanks 🙈 🙉🙊
@mitchdenner9743
5 жыл бұрын
Your a fuckin hack!
@davebatman847
4 жыл бұрын
Caulk! Caulk! Caulk! ,, thats all you in the US cand do, caulk the shit out of every thing why not cover the cover roof in caulk and forget the shingles and tin,
@martinjvillasenor773
4 жыл бұрын
Lots of open cuts and corners. . . Allowing on caulking for long term water title seal . . . Not good practice!!
@dodo14041980
5 жыл бұрын
hahaha.this is the stupidest way i've ever seen
@martinjvillasenor773
4 жыл бұрын
Garbage system . . . surface nails in waterways?
@ruthdanielson919
Жыл бұрын
These days looks like roofers wouldn't know what to do without caulk. 100 correct, shouldn't be any nails on the apron flashing.
@r.w.fields
5 жыл бұрын
Where's the cricket? FAIL
@eddiegreg7064
5 жыл бұрын
I believe code says anything over 48", common sense and experience tells me that anything over 36" should have a cricket. You also must factor slope, region, roofing materials, etc. I personally think this is not a good way to flash a chimney using this material, but what would I know, I've only been doing this since 1987, and learned from older highly skilled Craftsman. I see a lot of failure points and skipped steps. Thanks 🙈 🙉🙊
Пікірлер: 33