Thanks for th video sir! I just did mine. All my stuff was still on. I used all my 1/2 drive extensions and a wobble joint. But my son was on top and it was 1 1/8 I believe, and my bolts was ran in from the bottom. Used the motor weight and screw driver like you said and they pretty much went right in
@MatthewReedTrucking
Жыл бұрын
I'm glad it was helpful to you, that's why I made it, I couldn't find one myself. I may put my bolts in from the bottom next time I do them.
@terrybirdhowtod.i.y6008
Жыл бұрын
@@MatthewReedTrucking I forgot to add my 20 ton jack has the spring and plate on it so I used a 2x4 turned sideways “3 1/2” was up and down to lift and clear everything
@CFLDumpsters
3 жыл бұрын
I just did mine you def have to use the motor weight to get them to seat properly. Good video
@806pete9
3 жыл бұрын
Need to do a video on the rear bushings now. Good video straight to the point!
@MatthewReedTrucking
3 жыл бұрын
I'll have to look and see if I made any videos. They're pretty simple, if all goes well. The passenger side was easy! But my drivers side, I had to remove the bracket off of the block, because the metal part of the bushing, rusted to the bolt. Being there with the computer and fuel lines, I didn't see a good way to cut the bolt off. Just get all you're bolts started thru the frame, before you let the motor down, and you should be good!
@RamonLopez-pz1sp
3 жыл бұрын
Great video, you make it look simple 👍
@RC-Heli835
2 жыл бұрын
On 07 KW T800 a socket is not an option to hold with because the harmonic balanser is above it. Maybe a cut box end wrench will work.
@truckingc
2 жыл бұрын
great video! thanks man
@markyisser9004
3 жыл бұрын
Thank you
@slayer77000
8 ай бұрын
I think you should address the oilleak and your eyes would of thankyou if you washed it before working on it. Still A for effort. 😊
@MatthewReedTrucking
8 ай бұрын
The oil leak is how I got to that point, it was the front crank seal leaking. So everything was out of the way for doing the motor mounts.
@jamesray3920
3 жыл бұрын
Looks like u installed the motor mount backwards or should not be any gaps im abut to do mine on my c15 cat
@MatthewReedTrucking
3 жыл бұрын
Sounds good, report back to the class on what you find out.
@Bosnianfear15
2 жыл бұрын
How many total engine mounts are there. 2 middle 2 front
@MatthewReedTrucking
2 жыл бұрын
2 on the front, and 2 on each side, near the back of the engine. So 6 total on mine.
@Bosnianfear15
2 жыл бұрын
@@MatthewReedTrucking i got c15 acert gotta replace them, engine jumps quite a lot to the right, i seen two on front and two on the side , idk about the back, going to do some research on them.
@lonnieblackwell9215
2 жыл бұрын
That is not right, it should sit flush.
@rickearl1956
Ай бұрын
He doesn't show the removal and the install, i thought maybe when he impact it back in it pulls or sucks in where its through a flush. We didnt see any of that but yeah, something he did isnt right
Пікірлер: 20