Hi, is it a m10 x 1.25 20mm bolt for the new p bushing?
@PiggyPower
4 ай бұрын
Usually M10 is 1.5 ... But ymto be sure I'd suggest you check a bolt against the thread on the bush and then get the right ones (if you've not got a big ol' tray of used bolts like me!)
@ignaciopereyra1800
Жыл бұрын
Excelente Trabajo gracias Amigo. Saludos desde Uruguay un abrazo Gigante!!!
@PiggyPower
Жыл бұрын
Hi there! Great to hear from international viewers! 👍😀🐷
@elcheapotravel5914
3 жыл бұрын
nice tutorial, i will have to do the same but the other way round, my car has the aluminium part you are installing but i can't find it anywhere, everyone has the type you removed, is there a metalic one with m10 hole?
@PiggyPower
3 жыл бұрын
Part number is in the description 👍
@林志仁-r7o
Жыл бұрын
Hi,is new one stiffer than old?
@PiggyPower
Жыл бұрын
Yes of course!
@prawnyb
3 жыл бұрын
10:30 Et voila! Marvellous mate. 🤙
@ramazangemici3794
3 жыл бұрын
Great. Especially the detail you gave about the front bush was grea
@PiggyPower
3 жыл бұрын
No worries 👍😊
@ogamiwarzone7268
2 жыл бұрын
Hey piggy I need to change my front sub frame on my 1996 d turbo I'm not sure what one I can use I only find petrol sub frames for sale
@PiggyPower
2 жыл бұрын
DTurbo is just a spec. If your searching just for that, widen it out. The only issue I've found is gear linkage bolt location differences, this was easy to sort from memory. Otherwise they are indentical across all years.
@FraxinusExelsior
2 жыл бұрын
Really great informative videos on this channel for sure!
@PiggyPower
2 жыл бұрын
Thanks 👌🐷
@kurtseyffert6649
5 жыл бұрын
r.i.p headphone users those damn birds
@PiggyPower
5 жыл бұрын
Yeah, they are.... Tweeting annoying ... I don't notice them until edits as I just work along side them 😂 Apologies... But I'm not bird mass murderer 😂👌🐷💪
@jameswragsdale8676
3 жыл бұрын
Thanks for that video. I've got this job to do so it's been handy
@PiggyPower
3 жыл бұрын
No worries 😃👍🐷💪
@R0d0d3ndr0n
Жыл бұрын
Dude you are a boss, so much info, part numbers, suggestions. So much good in one video ♥
@PiggyPower
Жыл бұрын
Thanks 👍🐷
@zwloki0
Жыл бұрын
Very important, after job like that, go and get the alignment done. Also is that Very bad pitting on the inside of the brake disc?
@PiggyPower
Жыл бұрын
Important after any suspension change or remove/refit to check wheel alignment 👍 I dunno about the brake disc, I can't see your brakes from here 😜
@zwloki0
Жыл бұрын
@@PiggyPower i could swear that there was a lot of rust on your brakes 😉 . Anyway I got the bushes for my 306, The poly bushes are way too expensive.
@PiggyPower
Жыл бұрын
@@zwloki0 yeah the Powerflex ones are a huge difference and the older ones don't fit great tbh
@azzi.arthur
2 жыл бұрын
Hey Piggy, I'm looking into doing this mod myself, but I've heard people say you also need to modify that bracket of the sway bar bush that presses down on the the P bush, since the new P bush is thicker. Is that right? Does it really make any difference?
@PiggyPower
2 жыл бұрын
It's TINY bit thicker but really not enough to care. I've never had issues.
@azzi.arthur
2 жыл бұрын
@@PiggyPower great! Thank you!
@PiggyPower
2 жыл бұрын
No worries! Please consider subscribing and sharing 😃🐷
@DevinderAthwal306
5 жыл бұрын
Nice video but it looks like you damaged the bottom ball joint boot with the pry bar at 7:14. I use a tube tied to the ball joint end and a piece of wood under the subframe to lever off. I think this is shown in the Haynes manual for the 206.
@maxautouk
5 жыл бұрын
You realise that's just WD-40... right?
@PiggyPower
5 жыл бұрын
No damage to that ball joint 👌 That is a method shown in the Haynes, but it's 9/10 times useless as you can't lever the bar down low enough unless the car is jacked up 3 feet in the air. 👌
@marke293
2 жыл бұрын
Are the lower arms a a RCZ the same as you have there ?
@PiggyPower
2 жыл бұрын
Not even slightly. Other them having bushes and a ball joint and being called a lower arm 😂👍🐷
@metronomexxx
5 жыл бұрын
Great job Piggy! i miss to the 407
@PiggyPower
5 жыл бұрын
Me not so much 😂
@prawnyb
3 жыл бұрын
Do you live in some sort of forest surrounded by woodland creatures and birds?
@PiggyPower
3 жыл бұрын
I live in the countryside...so you'd think the birds would have places to live...but no... My workshop seems nice to them 🙉
@prawnyb
3 жыл бұрын
@@PiggyPower like a modern Snow White...
@PiggyPower
3 жыл бұрын
Or pig
@pierrecarmino768
5 жыл бұрын
thanks for this info. mate
@PiggyPower
5 жыл бұрын
No worries 👍 🐷💪
@thebishop74
2 жыл бұрын
I did this upgrade a couple months ago, and today just found out a downside to the mod. Wheel alignment I just got showed my castor angle has been reduced, which is not so great by my understanding. Most the aftermarket style ones often aim to increase castor to gain traction and more stability, where as this factory bush seems to take away like 1 degree of castor.
@PiggyPower
2 жыл бұрын
The centre point of these bushes to the centre point of the mounting bolts are the same. So there should be no change in geometry at all. I'd check other things on the vehicle if this is 100% accurate reading, comparing before and after.
@thebishop74
2 жыл бұрын
@@PiggyPower Actually, I'll retract that, I just went and looked at the Powerflex bush, and visually the change in the hole position on that and it gives .5, so there is literally no way the Partner bush would have done it. Now I am not trusting this wheel alignment much.
@PiggyPower
2 жыл бұрын
I'd be checking my front wishbone bushes and the ball joints. For a really accurate wheel alignment... There is adjustment in those wishbones by a little each side and in the ball joint bolts etc. You'd be amazed.
@thebishop74
2 жыл бұрын
@@PiggyPower I'm now wondering if someone put manual rack balljoints in my car at some point vs the power steering ones, cause that's the only thing I can think of that would be that far off spec...
@PiggyPower
2 жыл бұрын
Nah, they change camber and the ball joint would be all loose as they are a different diameter.
Пікірлер: 56