is there really a difference between this and the king clipper mod?
@man31903
Жыл бұрын
Is there a mod for the original detailers with the detachable blade
@gildeonsouza8080
2 жыл бұрын
Good morning, do you have the link to buy this adapter?
@kikado3
2 жыл бұрын
Check out philthy_blendz on instagram for link
@neko_the_barber9000
2 жыл бұрын
🔥🔥🔥🔥🔥
@kobanatroian6494
2 жыл бұрын
Hi man!whre diid you buy this green plastic i need
@lcpajaro
2 жыл бұрын
Hey man, videos are on point, the audio is kinda low though. Like the content though!
@kikado3
2 жыл бұрын
Good to know. I’ll have to turn the decibels higher.
@kobanatroian6494
2 жыл бұрын
@@kikado3 hi where can buy this plastic part?
@kobanatroian6494
2 жыл бұрын
Where can i buy this plastic part?
@infrarg916
2 жыл бұрын
Just ordered it how are they with bulk? I had ordered the mod previously from some other KZitemr and it was just garbage tbh but philthy blendz mods never fail to impress
@kikado3
2 жыл бұрын
With bulk ive had no problem at all.
@talknheadz
2 жыл бұрын
Stop using liners for bulk. It werars out your blade and motor. Use an adjustable, a 00000, or a balding clipper. Then bald out with a trimmer.
@infrarg916
2 жыл бұрын
@@talknheadz heard this a 1000 times some people just prefer to bald out with trimmers its a preference I have some to bald out and my hitters to line up. trimmers are way stronger then back in the day where they would get stuck going through bulk
@talknheadz
2 жыл бұрын
@@infrarg916 bro, im 37 years in this pool. Save money by using another tool to bald out then clean him up with liners. Thats all im saying bro
@V.C.I
Жыл бұрын
@@talknheadz 💯
@FaTaL1h
2 жыл бұрын
Does this mod hit harder then the stock blade setup?
@kikado3
2 жыл бұрын
It hits however good you set your blade. Same
@orlandorodriguez8422
2 жыл бұрын
❤
@iruleyounow
2 жыл бұрын
Just got it today. Not really impressed. It’s wayyyyy too loud. They didn’t make the cam follower long enough. The rotary motor only goes in like 1/8th of an inch. It’s just smacking around in there. If they would have extended the cam follower another quarter inch it’d be perfect. Was really hoping for some 🔥 but it’s a dud. Almost embarrassing to use since it’s so loud. Plus, when you set the blade in the mod as far down as possible, so the motor reaches the cam, where it actually stays relatively quiet, the shell of the clipper sticks out too far so you either cut it or it’s almost unusable. I’ll keep trying to mess with it but unfortunately I just don’t think this one will work.
@kikado3
2 жыл бұрын
Damn sucks to hear that. I know mine doesn’t make as much noise as it sounds like your getting. I know it matters where the prong falls on the cam follower. Mine work perfect. Let me know how you make out after you mess around with it. Best of luck man
@iruleyounow
2 жыл бұрын
@@kikado3 I ended up stuffing some thick construction paper with paper towels into the cam follower that meets the motor. Made it almost silent. Quieter than my FX. Now idk how long it will last but they hit like crazy so far. The cam really does need to be lengthened though.
@PhilthyBlendz
2 жыл бұрын
@@iruleyounow hey sorry you’re having trouble. This is the same distance as the stock reversed drawing. We went longer and it was very loud. Noise is within the springs laying on the cam. Springs shouldn’t be put forward. Hope this helps
@iruleyounow
2 жыл бұрын
@@PhilthyBlendz Ahhh okay. Well man I used them today and they were fantastic. They were just insanely loud before which really threw me off. I just kept tinkering with it and the paper in the cam worked perfect. Its dead silent. I figured you guys had tried different set ups with the cam, just from what I could see it looked like it needed to be longer but it makes sense why you didn't. It was flawless all day as well. I appreciate the help though! I'll keep buying mods for sure. It's too fun not to lol
@PhilthyBlendz
2 жыл бұрын
@@iruleyounow try moving the cam down a bit from the spring. Don’t seat the spring forward. Dm me on ig and I’ll show you
Пікірлер: 30