Show your support for my channel by treating me to a coffee! www.buymeacoffee.com/petestools
@OldCrowsClassicCars
4 жыл бұрын
Good video. You mentioned that the pilot arc still needs a ground connection, why is that, and what happens if you don't? Iv'e used the pilot arc that way, without ever using the ground cable, what will the differences be? Also, Is the pilot arc a feature of the machine itself or the torch? I ask because I wonder if it's possible to buy a pilot arc torch and use it on a regular non-pilot machine....I guess that might be in your other video... Thanks again for the video!
@petestools
4 жыл бұрын
Hi thanks for watching .You can use a pilot arc on a non pilot arc machine see my next video this saturday nz time. Its just a habit of mine to ground all my work i don't think you have to to make it work. Thanks again pete
@charliesmith9528
11 ай бұрын
Bought a new pilot arc torch to repalce non pilot torch,,new torch has 2 small wires and one larger black wire,,,old torch only had two small wires,,WHERE does the black wire connect to,,when i connected the two wires and pulled trigger unit made a scratchy noise,,??
@petestools
7 ай бұрын
its not the same setup as your old torch . you could try putting the pilot arc wire on your earth clamp. Works sometimes
@JMAJOR-ki7ur
5 ай бұрын
What is best for a cnc machine ,hf or pilot arc
@keithwins
Жыл бұрын
This would be so helpful but the video quality is terrible, I can't really see the inner workings of the torch, which is what I came for.
@petestools
7 ай бұрын
maybe you can do a video about it that easier to see
@russellsnyder4221
3 жыл бұрын
Totally under stand so your saying that you can put a different torch to turn any plasma cutter to a pilot start?????
@petestools
3 жыл бұрын
I have done it to 3 different units
@bartden9668
3 жыл бұрын
basically a HF torch needs contact with the surface your gonna cut to start. If you have a PILOT ARC, you can start cutting without touching the surface, so you can start a mm away from the surface. Pilot Arc parts (consumables) are a bit more expensive. Don't choose HF if you wanna cut rusty and painted stuff ór if you wanna cut in a non-contact way.
@petestools
3 жыл бұрын
you got it
@davidrasmussen2975
Жыл бұрын
What do consumables look like and how long do they last and what are their cost? Thanks
@petestools
Жыл бұрын
Cost me a hundred bucks for a set of 10 to New Zealand ,Compared to the normal consumables I use only 35 bucks .cheers Pete
@bolamnieplecy6363
2 жыл бұрын
So does that extra cable on the pilot arc go to the earth clamp on the machine to complete the circuit
@petestools
2 жыл бұрын
yea on a non pilot arc machine
@firstgenfarmer4154
2 жыл бұрын
Are the consumables for the ag60 and ag60p torches the same?
@petestools
2 жыл бұрын
No I think the p are shorter
@arva1kes
2 жыл бұрын
So you can just buy pilot arc torch for hf cutter and it will work as pilot arc?
@petestools
2 жыл бұрын
Not really will work in a pinch
@SpencerHarriman
4 жыл бұрын
Hey Pete. Your channel is highly informative and I enjoy your videos. Especially the plasma videos. Thanks For everything. Keep up the good work. -Spencer Minneapolis MN USA
@petestools
4 жыл бұрын
Glad you like them!
@charliesmith9528
11 ай бұрын
What gauage wire is pilot arc green wire
@petestools
7 ай бұрын
Whatever i could find .But it does get hot
@Thekingmaker
3 жыл бұрын
Thanks Pete from Detroit Mi
@petestools
3 жыл бұрын
COOL thanks , Detroit Mi keep safe
@Quantalume
4 жыл бұрын
Great video. I appreciate you taking the torches apart to illustrate the difference. It would be nice to see how the blowback style of pilot arc torch works as well.
@petestools
4 жыл бұрын
Great suggestion!
@mickeyvanaudenhaege3692
2 жыл бұрын
Can you fit a pilot arc torch to a cut 40?
@petestools
2 жыл бұрын
yea but only for short time use
@michaelkennedy2528
Жыл бұрын
Very nice video, to the point, none of that music stuff happening. It appears that the major difference is that the nozzle is grounded on the pilot arc and not on the scratch arc. What would prevent someone from making their " scratch start" into a pilot arc by running an earth ground back to the machine from the nozzle? I am very ignorant on the plasma cutter stuff, but basic electricity and wiring I am fairly decent at. Is that a possibility?
@petestools
7 ай бұрын
Your correct see my other videos about it.
@szbalogh
3 жыл бұрын
Excellent videos! I just made a TIG welder from an old transformer. I was thinking if it is possible to use it for plasma cutting? Saw the other video how to use a plasma torch in a TIG torch. Could You please make a video about scratch start plasma cutting?
@petestools
2 жыл бұрын
See my playlist
@jens-eriklangstrand1689
4 жыл бұрын
Where does the green cable go? Are you sure tourch with "pilot arc" can be used on like the CUT50? It does not have any terminal for that cable .. Also - when switching off my machine the fan stops immideately, while the LCD lives on for a while .. is this a fault? (I´ll just run the machine to cool it down after cutting, for like a minute ..)
@petestools
4 жыл бұрын
kzitem.info/news/bejne/0GdnqYGGf3N6iqQ
@TechieTard
3 жыл бұрын
FYI Guys, for the plasma return is his talking about, if it's a straight cut, begin at the very edge of the material you will be cutting through when you start the surface contact. If it's a cut through the middle, start the cut at a 45deg angle and work it into a 90deg angle so that the plasma blow the metal away from the nozzles core.
@petestools
3 жыл бұрын
You got it my friend
@paulcollins8296
3 жыл бұрын
Great video thanks. I bought a cheap Cut 50 HF start plasma cutter. Is it possible to buy a pilot start torch and use with my basic machine? There is an earth post on the back of the machine. I understand how the pilot start torch works but cannot see why a pilot arc torch would not work on an HF start machine. Thanks.
@petestools
3 жыл бұрын
Yes you can! kzitem.info/news/bejne/wminxX-QknmEl2k
@theogmrbill1
4 жыл бұрын
What are your thoughts on the ct520df. Not the ct520d. I believe the df is there touchless Pilot arc. Im interested in this because it does tig, arc, and plasma. But im hesitant bc im not sure if i wasn't too go with ct520df or ct520d
@petestools
4 жыл бұрын
Hi bill , I like this machine personally PRIMEWELD CT520DP Pilot Arc 50A Plasma Cutter /200A Tig/Stick Welder Combo welding machine especially if your using it for tig welding as well? amzn.to/2CXACoG and It uses quite cheap consumables that are readily available. But if your just wanting a plasma cutting machine i would go for something a big bigger maybe 80 amp as that will cut in excess of 1 inch plate without breaking a sweat. (Of course you have to have bigger power supply in your workshop to run it) Thanks pete
@everythingsucks6086
2 жыл бұрын
Very good explanation buddy!! Thanks for the video!!
@petestools
2 жыл бұрын
Thanks mate
@luckyblue1986
3 жыл бұрын
Fantastic video, excellent explanation of the differences of the torches and how they work. Huge help in my search for buying a plasma cutter.
@petestools
3 жыл бұрын
Glad it was helpful!
@charlesbugeja8313
2 жыл бұрын
great info Pete i didn't do my home work and bought a non pilot cut cutter and your trick is a god send i was going through consumables each time i used the machine but not any more Cheers Mate
@petestools
2 жыл бұрын
Glad I could help
@christobotha7191
4 жыл бұрын
Uncle pete. Thank you for the video. Best so far. Regards Christo from South Africa
@petestools
4 жыл бұрын
cool cheers
@adamlee581
2 жыл бұрын
Hey Pete Great no nonsense videos. Can you gouge out welds with a pilot arc torch?
@petestools
2 жыл бұрын
yea i would give it a try
@kernowcoinringscornishcoin3999
4 жыл бұрын
Hi Pete After watching your vids on pilot and none pilot torches noticed you had run a wire on one of your torches but not straight to the tip have you a vid on how you ran the earth wire and how you concealed it
@petestools
4 жыл бұрын
Hi mate Checkout this video Plasma Torch Pilot Arc Conversion Easy : kzitem.info/news/bejne/oo-bvnhtnICDlIY
@davidcornell271
3 жыл бұрын
Hi Pete, great video. lots of info. I really enjoyed it and learned a lot as well. have a great day. thank You
@petestools
3 жыл бұрын
Glad it was helpful!
@kuskus231
4 жыл бұрын
So what would you recommend , I would be cutting new / old steel rusty painted etc , I'm guessing pilot arc? Any plasma cutters u recommend on a budget?
@petestools
4 жыл бұрын
Hi mate this is about the best value pilot arc under 300 bucks i could find .Also the consumable cost is not to bad for this style torch compared to some others. amzn.to/33ZCnxo cheers pete
@genoory5090
3 жыл бұрын
Can you connect a pilot arch torch to a non torch plasma cutter?
@petestools
3 жыл бұрын
yea
@ElTano318
4 жыл бұрын
Hello! their videos are very good! very instructive! yesterday they gave me an old Saf brand plasma cutter model nertazip207 without the torch. I could see that the arc activation is by contact. What torch do you recommend for that application? Sorry My Bad English jejeje Desde Buenos Aires, Argentina
@petestools
4 жыл бұрын
Hi how many amp is your machine?
@ElTano318
4 жыл бұрын
@@petestoolsI don't now... Don't have specs for this machine... but is small machine... For hobbie and small cut
@colinlindsay9503
4 жыл бұрын
So can I make my none pilot arc mig into a pilot arc by changing the torch and earthing it to the machine.
@petestools
4 жыл бұрын
are you running a pt-31 plasma torch?
@A7Xafterlife94
3 жыл бұрын
Awesome video! I just picked up my first HF plasma cutter and this explained a lot! Thank you! So for clarification, with a HF cutter, does the tip need to be in contact with the metal at all times? Then just drug along for the cut? Thanks!
@petestools
2 жыл бұрын
Yep cheers
@gladams7405
2 жыл бұрын
pete's tools k
@arkadybaskin5716
4 жыл бұрын
Very well for understanding, thanks.
@petestools
4 жыл бұрын
thanks mate
@feednspeed1835
4 жыл бұрын
Great info, Pete! Thanks. The Chinese Cut50 H that I just bought has the pilot arc type torch on it from the vendor. There is no pilot arc lead in the cable that is noticeable. The torch will come apart this week to see if a lead is routed but not pulled through. there is a ground to chassis screw at the rear of the machine. If there is a lead, or if one gets routed, can that just be connected to the chassis ground and be expected to work? Could that cause any issues with the machines circuitry?
@petestools
4 жыл бұрын
Hi what sort of torch is it?
@feednspeed1835
4 жыл бұрын
@@petestools , It is an SG55 torch.
@untoyotero480
3 жыл бұрын
Great video, thanks for making it!
@petestools
3 жыл бұрын
My pleasure!
@picturefish40
3 жыл бұрын
Thanks you help me a lot. Stay safe
@petestools
3 жыл бұрын
Thanks, you too!
@ianfosterUSA
3 жыл бұрын
Brilliant thanks from the UK
@petestools
3 жыл бұрын
Very welcome cheers mate
@97kt69
4 жыл бұрын
Great informative vid thanks.
@petestools
4 жыл бұрын
Glad you enjoyed it
@danthemans
4 жыл бұрын
Thank you for this video
@petestools
4 жыл бұрын
No worries!
@kathygallagher7378
3 жыл бұрын
Great info! Thank you Pete!
@petestools
3 жыл бұрын
Any time!
@GCBFABRICATION
4 жыл бұрын
Can used cnc.?
@petestools
4 жыл бұрын
yes
@smartliketruck
4 жыл бұрын
Jeepers, I thought the nanny state laws are getting out of hand up here, apparently down under you have to wear hi-viz in your own home shop :) Thanks for clear explanation of differences between the torches
@petestools
4 жыл бұрын
The laws are crazy here as well . Not quite to the stage of wearing hi vis at home yet lol. I wear it all day at work and dont bother taking it off for my videos ,cheers pete
@melgross
4 жыл бұрын
Another disadvantage of HF start is that when cutting a grate, or anything with fairly large holes, the arc goes out when you get to a hole, so you have to start the arc again. Go through 50 holes on a sheet, and that’s starting the arc 51 times. Not only is that a real pain, but it wears the consumables out much faster. With pilot arc, you just keep cutting. By the way. Excellent explanation.
@petestools
4 жыл бұрын
Yea totally agree .It seems the more you stop and start your consumables don't last as long. cheers pete
Пікірлер: 93