It's amazing. how many times I watch this video over and over again, there's so much things embedded into this video
@Mr-er3yo
3 жыл бұрын
I'm a emerging piping engineer sir your way of teaching is excellence.i keep on watching your videos.great efforts continue
@daurentokkuzhuyev4791
3 жыл бұрын
Very good, always seaching your New videos in your channel. I have got a lot knowledge. Want to tell many thanks. Dont stop and keep going Mr
@abdoadam7248
2 жыл бұрын
Thanks for sharing knowledge
@himelmahamud304
8 ай бұрын
It's helpful video ❤
@sen-ow7ub
2 жыл бұрын
Really well explained. And we are understood very clear. Please make another part video about this topic. Please make minimum one video everyday related piping design, detailing, fabrication, piping welding and NDT requirements, construction Method and pre commissioning. . Thanks. Why there is no frequent videos now. When you going to post your next video.
@heshammatoug4860
2 жыл бұрын
thanks for this clear explanation. one question, please. can we use ibc gasket instead of spiral wound gasket ?
@sarankathir4857
3 жыл бұрын
Very useful
@pratikdaundkar5613
7 ай бұрын
very informative
@positivevibes7713
3 жыл бұрын
Can u make video on how read ga and fabrication drawing for piping design.
@Shivam.366
Жыл бұрын
Thanks
@GemmyHeart
Жыл бұрын
nice.
@Sam-81_98
Жыл бұрын
Hello Sir. Great video. Is it possible for you to recommend a good vendor who supplies flanges of International quality for the overseas market?
@fireballxl5328
Жыл бұрын
Texas Forge, or check with MRC co stay away from China, Korea, India
@Borntobeviral
4 ай бұрын
3 types of gasket mainly used 1. SS graphite spiral wound mentality gasket for raiaed face 2.Non metallic type ring gasket for raised face 3.Full face gasket for full face
@rohitnikam3647
2 жыл бұрын
Hi sir Can we use full face gasket on rf flanges
@gourisankarsamanta7670
2 жыл бұрын
Yes we can use it.
@chandrajeetsharma1
3 жыл бұрын
Gd eve.. sir Sir i am also an engineer Right now i am struggling in this feild Sir could u tell me different between ASME, ASTM, API, ANSI, and could u provide me a pdf of it . It my humble request to u sir please 🙏
@gourisankarsamanta7670
3 жыл бұрын
Please watch my various piping videos, particularly the following : kzitem.info/news/bejne/uI6k0pqXe3qBlnY kzitem.info/news/bejne/1Hugz6iAo2Zhi2k kzitem.info/news/bejne/k6Gf0XuOrHiXp6Q kzitem.info/news/bejne/s2-uyImjqpSmnX4 kzitem.info/news/bejne/lndvvGmVZoSriHY kzitem.info/news/bejne/pqibm36GinSGqH4 kzitem.info/news/bejne/t45vp65-imeQe20 kzitem.info/news/bejne/lYChn56LhpqepaA kzitem.info/news/bejne/kq2as4yskaygm5g kzitem.info/news/bejne/rJCknH2kgnOBgn4 kzitem.info/news/bejne/rqR52HttqJp-i3Y kzitem.info/news/bejne/tWep0IOPkWKImKg kzitem.info/news/bejne/uI6E1K53eqV1d5g kzitem.info/news/bejne/q4uP1Gyqo2aorW0 kzitem.info/news/bejne/r56Lqnmisp-LlZg
@chandrajeetsharma1
3 жыл бұрын
@@gourisankarsamanta7670 gd morning sir thank you sir If i have any doubt i will contact u through this way
@fireballxl5328
Жыл бұрын
not a simple question. all these folks compete but are also in bed together. As time goes by all the U.S. recognized codes and std get closer Ill try to get back when I have a bit more time
@Borntobeviral
4 ай бұрын
3 types of gasket mainly used 1.SS graphite spiral wound mentality gasket 2.Non metallic type ring gasket 3.Full face gasket
Пікірлер: 23