Could you please share video about 3d model pipe isometric
@rajuparapati3638
Жыл бұрын
Exlent explainess
@Piping-engineer
Жыл бұрын
Thaks for watching and comment
@XtremeVeh
6 ай бұрын
Do you have a tutorial on how to draw this on sketchup .Thanks
@Piping-engineer
6 ай бұрын
Yes, If you watch our other videos you can see that,l am using Sketchup,Bandicam,clip champ and Canva
@deanmanuel9560
Жыл бұрын
Very good please show more in English.
@Piping-engineer
Жыл бұрын
Thanks for watching, Yes, will continue videos in English
@aliflankes8259
Жыл бұрын
Good drawing but sould be more descriptions
@XtremeVeh
6 ай бұрын
What softawre did you use to draw it on paper
@Piping-engineer
6 ай бұрын
Sketchup
@blakewilliams6613
5 ай бұрын
so a 45 degree is an up and cunfuses every thing. . . . . . figure some thing else for a 45 degree or find a better eplain for the 45 deg not to confused with the UP. . .
@Piping-engineer
5 ай бұрын
Many thanks for watching and comments, my friend. We will take your advice into consideration in our future videos.
@celiajuarez4376
Жыл бұрын
Can you show a isometric cube drawing
@rupangchannel888
10 ай бұрын
Thank you 🙏
@Piping-engineer
10 ай бұрын
You’re welcome 😊
@waleedyoussef5956
2 ай бұрын
من فضلك يا هندسة، elevation هو منسوب مركز الماسورة او الراسم العلوى او الراسم السفلى تحياتى واحترامي
@Piping-engineer
2 ай бұрын
مرحبا سيدي، شكرا جزيلا على المشاهدة وأفكارك القيمة
@scorpiontetteh-kf2ic
Жыл бұрын
Thanks
@arturj.8804
5 ай бұрын
Your wire bending is wrong? Two last angles are wrong. Your bending from north to east should be 90 degrees, your wire is clearly 45ish degrees. And then you should go straight up, also 90 degrees. Its a shame bc your explenation was correct but the wire bending makes it very confusing
@Piping-engineer
5 ай бұрын
Many thanks for watching and comments, my friend. You are absolutely right. After watching your video several times, I was able to understand what you said. Unfortunately, it is not possible to correct this in this video. We will definitely be more careful in our future videos.
@sergioxmc1
Жыл бұрын
software to drawing?
@Piping-engineer
Жыл бұрын
HI, are different software, sketchup
@sergioxmc1
Жыл бұрын
Sketchup? 😮😮
@RicardoDelasAlas-w6n
10 ай бұрын
Is that correct?
@King_Ingsley
4 ай бұрын
The wire bending is wrong
@Baiano7589
Жыл бұрын
2 curva de 45° ? Como assim?
@gilcineyteles
4 ай бұрын
O arame tá virado na coordenada ,mas porém fora de esquadro
@Piping-engineer
4 ай бұрын
Eu fiz uma nova versão deste vídeo, por favor assista também kzitem.info/news/bejne/k6qvmK54f2J2hW0
@rahimpakottik2794
8 ай бұрын
good
@Piping-engineer
8 ай бұрын
Thanks for comments
@luismaldonado4193
8 ай бұрын
Esta mal hecha las lineas, linea horizontal no tiene elevacion, linea vertical si
Пікірлер: 51