For those who aren't as experienced with Plasti Dip, I highly recommend masking off the car more to prevent overspray. Wind or no wind, you will most likely end up with some overspray. If you do, you can normally wipe it all way with a microfiber towel.
@shamefulidentity
9 жыл бұрын
Thank god this stuff is removable.
@REALthugnasty
8 жыл бұрын
💯 haha yep. artistic license revoked!
@Evillt1
4 жыл бұрын
ugly as fcuk!!!
@randyhunt7942
8 жыл бұрын
Nice work, ride looks good! I'm preparing to take on an all-over plastidip plus striping on my Mini so thanks for wet peel tip.
@robertplank6284
8 жыл бұрын
Actually looks good! I watch all of Dip Your Car videos too. That guy really knows what he's talking about!
@HayesTransport
8 жыл бұрын
A white primer coat would have made it pop more I think, Looks good either way.
@danielellis4939
9 жыл бұрын
looks good! word of advice when putting the first layer go slower not so fast you want to lay down a solid tact layer then the next coat make it thicker then the third and fourth make them slow and even to make solid coats. Good Job though!
@eckonalt
9 жыл бұрын
Daniel Ellis thanks for the tips.
@danielellis4939
9 жыл бұрын
no problem
@AMindInOverdrive
8 жыл бұрын
Looks good. I wonder how it would have looked if you'd have used the red to extend the lines of the read lights to a point along the side...maybe cool too. Also, I knew you were going to get over-spray from not masking off far enough...I did this a few times with airbrushing projects
@poasei
7 жыл бұрын
massive red overspray on the grey and black for sure.
@BMH1965
6 жыл бұрын
I agree. I think most people would have seen that his lack of masking was going to be a problem before he even started. Very poor preparation.
@evadereckless7308
6 жыл бұрын
+BMH1965 easily peeled off after 30 mins
@xxFallenKnight
8 жыл бұрын
How much HP did u add to your to car by doing this?
@TheTrueArix
8 жыл бұрын
+xxFallenKnight how does it make you feel to take the bus?
@zeid001
8 жыл бұрын
Hahahah
@theunknown5005
8 жыл бұрын
lmao!
@jiberias
8 жыл бұрын
What a ridiculous comment. Silly.
@Logan5874
8 жыл бұрын
i painted my brake calipers white and it added 50 hp each.
@RICKYERE08
9 жыл бұрын
I personally think it looks terrible, but whatever floats your boat.
@realtalk4689
9 жыл бұрын
Very creative and nice job. Your car is officially personalized.
@vincentlawrence677
7 жыл бұрын
You have A LOT more than 3 or 4 coats on that. Going over it 20 times doesn't equal a single coat. You can also see the spray marks in the black.
@kabba4575
8 жыл бұрын
I'm surprised how nice it worked out because your spray technique was pretty scary if you were using car paints because if that was it wouldn't look real good u would of had alot of bleeding in the paint not to mention your coats would be very off. But it looks good so props to you.
@eckonalt
8 жыл бұрын
plasti dip is very forgiving
@elizabethleach2753
7 жыл бұрын
Says he's doing another coat. Puts down the equivalent of five coats
@francosworld5030
4 жыл бұрын
Looks Great! on the Grey! - Leave it Alone - Less is More! Looks Great!
@TheBastion87
3 жыл бұрын
gotta do right side all over again or cover it again with black paint. good thing with plastidip is it doesnt show overlaps
@KevinHerronArt
8 жыл бұрын
Sick car man, really like what you did , but agree about widening up the lines so it streamlines with the tail light. Ah well, you can always do that next time you dip your car in 2 years.
@NathenMixon
8 жыл бұрын
I didn't think an optima could look any better. Awesome job
@eckonalt
8 жыл бұрын
thanks
@Casinolife07
7 жыл бұрын
I did two simple stripes on my hood, but it feels rough not smooth at all. The color was black PD. I placed the can in warm water for 15 minutes and shook the can for at least a minute or two. I thought it would be much more smoother!!
@chriscs9080
3 жыл бұрын
plasti dip is smooth as fuck .. you did it wrong! Maybe you sprayed from a long distance? also the first 3 coats have to be very thin in order to be glossy
@fernandocg7859
8 жыл бұрын
wow! looks really nice. congrats.
@William9alex
8 жыл бұрын
So I'm guessing you dipped the black on the panel before the red? I'm just serious because I have a project in mind where it'd involving taping up previous plasti dip to get a certain pattern. Was wondering if the tape would damage the previous plasti dip at all. I don't see why painter's tape would but I'd like to be certain.
@eckonalt
8 жыл бұрын
as long as the dip that your taping on is dry it shouldn't damage it. but if you want sharp lines the tape has to be pulled of while the last coat of the new dip is still wet. go to 6:15 of the video
@tomerrozenman4484
8 жыл бұрын
Looks Badass, man. very good job. could you tell me how long you waited between coats? and one more thing, tip for the future. you should make sure the tape closest to the paint is the one to go off first. just to assure the paint wont dry on you.
@eckonalt
8 жыл бұрын
+tomer rozenman i waited around 20 minutes between coats. and thanks for the tip.
@coreylongenecker2288
9 жыл бұрын
did you change the badging on that car? i have never seen it as a K5 before.
@reymundocastro87
8 жыл бұрын
if you want Plasti Dip colors to be more bright and popping always use a white backing
@Unkown214
8 жыл бұрын
Not just for dip, but for painting in general.
@funkycowie
8 жыл бұрын
Definitely should have followed the line made by the lights. I've learnt something though, wasn't sure how to best do striping.
@speedbird983
Жыл бұрын
Looks cool!
@prllme
8 жыл бұрын
The Veloster Turbo badge is a nice touch
@Antonio953digit
8 жыл бұрын
Didn't do a good enough of covering the car. There's still red plasti dip overspray on the car.
@sNstRflyEr
7 жыл бұрын
Why would somebody use Plasti dip instead of paint? I'm planning on painting my springs with paint and then heard of Plasti dip..why not use paint? why do people use Plasti dip? What are the advantages? does it peel off?? I just really want to understand what the deal is with it, and why it's used in place of paint, thanks!
@motortalk5147
7 жыл бұрын
sNstRflyEr Yea you Can Peel it off, but it won't stick to springs, since it is not flexible. It's like rubber
@gmangarcia171
8 жыл бұрын
cool looking. what else have you done ?
@toyotasupra4331
9 жыл бұрын
It would be quite good if you put a couple of coats of glossifier to get more of a contrast between the black and red :)
@eckonalt
9 жыл бұрын
Toyota supra 43 i put only 1 coat of glossifier. think i might try more next time.
@toyotasupra4331
9 жыл бұрын
Sounds good :)
@TimBrownie
7 жыл бұрын
I think that the red should match the red that is in your lights. Also, the bottom line should match the top line, in my opinion.. that way they will come together.
@Sonu26tanwar
8 жыл бұрын
u can put a white stripe which passes over the gas tank cap
@Nicchitta
9 жыл бұрын
Go Rangers baby!! haha i heard the accent as soon as the video started (Brooklyn native, here)
@houseofhouse9840
6 жыл бұрын
Brooklyn all day baby i miss home native new yorker we everywhere!!!!
@Johnny-zz1zv
9 жыл бұрын
Looks like the car came out the assembly line that way... Nice!
@simplytuned1623
7 жыл бұрын
looks good but I think,the res stripe should match itself its kind of off to the side and it would bother someone with ocd
@kylewood709
8 жыл бұрын
yeah what do you call the badging that you did? could you make a video that would be awesome
@TheAndyrndn
6 жыл бұрын
Looks good. Where did you get the attachment for the plasti dip can?
Did you also lay down the black plastip with a regular can like you did the red? Looks pretty smooth.
@eckonalt
9 жыл бұрын
Ariel Hernandez Yes. I used 3 full cans and 1/2 of a 4th.Sorry it took so long to get back to you.
@arielhernandez5726
9 жыл бұрын
Cool, looks good!
@brenthirak
8 жыл бұрын
looks GREAT man
@eckonalt
8 жыл бұрын
+brent hirak thank you
@Rolandswebkro
9 жыл бұрын
cool tried on my car in forje week but dip dried too fast. any suggestions?
@Evillt1
4 жыл бұрын
12 year old girl on my street did the exact same thing to her bike last week!!!!
@sN1P3Rxb3AsT1257
9 жыл бұрын
+Gerry B What other kind of tape is there besides the masking tape you were peeling off?
@eckonalt
9 жыл бұрын
I mostly use painter's tape. But some automotive stores have some specialty masking products. Check out dip your car.com
@eckonalt
9 жыл бұрын
Gerry B dipyourcar.com
@yoyo3028
4 жыл бұрын
Is there an edge between those two colours which you can see and feel? Like difference in height
@eckonalt
4 жыл бұрын
Slight
@deadlyhydra
8 жыл бұрын
That Looks very good
@timwilliams5144
8 жыл бұрын
with the edges of the dip being exposed like that was it any less durable?
@eckonalt
8 жыл бұрын
+Tim Williams not at all
@kyelermorgan5345
8 жыл бұрын
it would of popped and been more vibrant with a base coat of white
@starvator
8 жыл бұрын
looks really nice. I might add somethinglike this, i've only dipped my a4 rings
@djkary4ever
8 жыл бұрын
Looks great!👌
@Marcikutyaful
9 жыл бұрын
Not too large and not too small, Nice. The masking was insufficient...
@Alex-wm3pn
8 жыл бұрын
I actually really like how it turned out.
@WhiteGravey
7 жыл бұрын
lol at overspray did you really not see that coming?
@kevinrex9696
8 жыл бұрын
The shaking of was overkill
@WisteriaBerlitz
9 жыл бұрын
not bad, I like it
@leonardoavila4275
8 жыл бұрын
Una pregunta maestro . quiero pintar las micas de mi auto con esa pintura plasti dip . se puede .
@JoseMartinez-ii9pf
7 жыл бұрын
Leonardo Avila SI de puede
@jrgen4672
9 жыл бұрын
That turned out to look too damn good :)
@nesco7615
4 жыл бұрын
Hey bro how long did it last
@OneCheapEric
8 жыл бұрын
Looks great man!
@Spartan117A51
8 жыл бұрын
hey man when you do the coats how long you wait in between because my car came out okay but nowhere as good as I know It could be?
@eckonalt
8 жыл бұрын
i waited around 20 minutes in between...
@SonOfaAsian
8 жыл бұрын
Did you paint this over black plasti dip?
@eckonalt
8 жыл бұрын
yes I did it over matte black
@nutty13132
8 жыл бұрын
hello. what is you masking tape? My tape is attache pastdip thank you
@1SIK500
8 жыл бұрын
+บวร อัครวิไล Blue painters tape
@mrklimczyk
8 жыл бұрын
Looks awesome
@goldenTym
9 жыл бұрын
I think it would look sick if you did the rest of the back end the same black.
@chrisaquilano1688
8 жыл бұрын
ya dude deffinatly make the strip bigger, looks sick tho
@mrpunisher739
8 жыл бұрын
nice design! double like haha
@REALthugnasty
8 жыл бұрын
I think it should be smaller. like so small you can't see it. gotta make your own lines bro, not just paint an entire panel.
@lucasmuller9239
8 жыл бұрын
+Grant K you've obviously never done graphics on a car have you. Because if you don't follow the lines or the flow of the car it looks like garbage. If it doesn't flow it looks tacky, and plastidip gets too much hate for looking tacky because of the inexperienced morons that use it like a toddler with finger paint
@vladymartinez1232
5 жыл бұрын
@Grant K 🤣🤣🤣🤣
@enriquepenanieto4701
8 жыл бұрын
nice work!!
@JoshsFavorites
8 жыл бұрын
looks bad ass, I might do something similar with mine - good stuff
@nicholaswarren48
2 жыл бұрын
Dip is probably gone by now but if you re-do it it would look sick as he'll with a red gas cap for an accent
@tgo.382
9 жыл бұрын
looks good
@kendricksojka9759
9 жыл бұрын
Asome
@skynetHI
8 жыл бұрын
put the stripe in the middle of the black stripe
@jamesdang3291
7 жыл бұрын
So sick. I'm doing this to my car.
@NunoRVOliveira
8 жыл бұрын
Anyone knows where to buy aerosol cans of plastidip in europe? Can't seem to get them under 20USD each and everyone says they are super cheap... Am I too optimistic or does this really cost 20 USD per can? And how much can a can do? 4 coats on a car door, 2 doors?
@eckonalt
8 жыл бұрын
do you have amazon there if so that is where i get some colors.
@NunoRVOliveira
8 жыл бұрын
+Gerry B thanks for the reply. We have Amazon but it's either expensive or they don't ship to Portugal. Seems I'll have to get them from UK friends. But the best price still close to 14USD per spray can...
@eckonalt
8 жыл бұрын
Try this website www.dipyourcar.com/
@ahmett9289
8 жыл бұрын
So Cheesy I could make a sandwich.
@IsmaGonzalo
8 жыл бұрын
It's durable in washings?
@eckonalt
8 жыл бұрын
yes..I go through the car wash with no problems
@Logan5874
8 жыл бұрын
Nice
@DavidODST
8 жыл бұрын
I really like this man
@Racerboy535
7 жыл бұрын
Don't mean to be a troll but your spray technique needs some work.
@jdamage5002
8 жыл бұрын
biggest blinker light ever..
@AceNikeSb93
5 жыл бұрын
wtf is this need for speed underground
@eckonalt
9 жыл бұрын
Corey Longenecker i did re-badge. I purchased the K5 and other's from the link below www.k5optimastore.com/ in Korea the optima is known as the K5 The graphic in the middle is my family crest..I had a local graphic guy print it for me.
@litonavera777
6 жыл бұрын
can you turn on the volume of your audio a little louder please, we can't what you're sayin...
@vct33
8 жыл бұрын
I think it would look good with a red fuel door too.
@ndk2k4
9 жыл бұрын
now sprinkle some rice on it, and youre done.
@dariusdaves3164
8 жыл бұрын
looks dope
@akarim909
7 жыл бұрын
RICE, RICE BABY
@n8rad3
8 жыл бұрын
No mask?
@emmanuelalcudia8394
8 жыл бұрын
nice
@kinggeneral3189
7 жыл бұрын
looks kool 👍👍
@ostenhooker5228
7 жыл бұрын
keep the overspray
@zetty8977
9 жыл бұрын
ur insane for not covering the rest of the car with something.
@nycaight
8 жыл бұрын
Dope as is homie 👍🏾👍🏾
@austins.5542
8 жыл бұрын
its going to come off when you fill up. i know, i had it happen to me.
@chris.5434
4 жыл бұрын
Austin S. Cuz you don’t know how to pore gas... if you drip gas on dip yes it will peel that’s pretty obvious
@marcodoz
8 жыл бұрын
what a way to mess up a cool ride!
@GameHEADtime
8 жыл бұрын
nah bro if anything its plasti dip protect paint from dirt and rust etc everything car are lucky to have all this stuff to have it last longer it could be worse if it were can of paint spray...like they used to do when plasti dip wasnt so popular....
@stevenvigoa2710
6 жыл бұрын
you have streaks in your black ... iam not a big fan of this red
@soullessone4681
7 жыл бұрын
that's not how you thoroughly mix a can of spray paint
@soullessone4681
7 жыл бұрын
long strokes up in down is the wat to go
@windwave42
9 жыл бұрын
How long in between coats sir?
@eckonalt
9 жыл бұрын
maybe 10 minutes,give or take
@TheBalcerman
8 жыл бұрын
Terrible. And that over-spray caused by bad masking is just super lame. Disaster. I'm being honest. That's exactly what I would say if my best buddy would do that. Well. I will probably slap him in the face as well. As for the job? Lines are not straight, both sides looks totally different, and that over-spray. Oh, and it looks tragic but that's just my different taste. No point to discuss what is the reason of doing that kind of "modification".
@walkergillette3918
9 жыл бұрын
there was over spray, because you were to careless
@eckonalt
9 жыл бұрын
CRAVEN MOREHEAD it was a little windy that day. idealy it would be nice to have an indoor location to use ,but with plasti dip it is easy to get the overspray off with a little Goo Gone.
Пікірлер: 192