As a machinist I have to say he’s doing the hemp wrong. You need to roughen up the thread that the hemp holds better. In the scratches it gets a good grip. You can do it with a file or sawblade. Many fittings even have already little grooves in it for that case. Hemp is more mess but will expand in contact with water and make the connection even tighter and better. You can even turn back a little with hemp without getting a leak. Ptfe is cleaner but you can’t turn back. Hemp is still a great material and superior in some cases, even if its used less today. Please show it right when it’s a tutorial, or knowledge gets lost.
@Prokudak
2 жыл бұрын
Thanks for the explanation. When would you use one over the other?
@niklask.5593
2 жыл бұрын
@@Prokudak I would use hemp for things I still need to adjust like water taps. It’s easier to get the direction right. I mostly use ptfe sealing thread or tape for all installations. Hemp I use less because it’s more work, but it’s the longer lasting way.
@littlereptilian7580
11 ай бұрын
What is this grease he is using??
@niklask.5593
11 ай бұрын
@@littlereptilian7580 I don’t know, I’ve never seen it before. Here in Germany we use ,,Fermit‘‘. It’s a grey sealing paste which you put on the hemp. It makes the hemp swell when it’s threaded in and ensure a tight connection which is still adjustable unlike teflon.
@GO-mg7ft
9 ай бұрын
You are in general right but is not wrong but with slightly rough edges will be better. Some valves already have fabricated nails on thread
@user-uh2uw7ey3b
Жыл бұрын
As a plumber i can say both of your tutorials here a wrong. Threads should all be scratched up to grip the sealing material in this case hemp and ptfe. The hemp is too thin and needs to start from the first thread, yes maybe it didnt leak but i doubt it. I only use ptfe tape on threads where one or both of the fittings is plastic, or gas. I use hemp or loctite thread sealing cord on anything metal but hemp is the better option. I apply ptfe starting from the back of the thread and work towards the front. The ammount of wraps depends on the pipesize but i make sure to taper it towards the start of the thread
@nathanbrown19
19 күн бұрын
After reading the comments, using longer bit of hemp, less grease and crossing the thread with the hemp I had immediate success! Thanks all!
@JawellNofine
6 ай бұрын
Interesting video. I am 67 years old, my father was a plumber. I will probably be bombarded with ecologists etc. on this page, but my father always put enamel paint on the threads before applying hemp, and then covered the hemp with enamel paint again before joining the pipes. You know what? the pipes never leaked and no one ever died of cancer etc. My ex neighbour from 25 years ago ( a plumber) saw me threading a pipe with that plastic crap, jumped over the fence and gave me some hemp. told me he would kick my nuts in if he ever saw me using that plastic crap again. I'm using hemp ever since and I'm proud of it. Do it the right way and it lasts for ever!!!!!!!
@allwillberevealed777
2 жыл бұрын
Came to see the comments. Bet this guy finishes one whole roll of paper when he hits the 💩
@ethanwasme4307
Жыл бұрын
cleaner arse than yours at the end of the day, cheap cunt.
@robertopapetta1837
2 жыл бұрын
Canapa a vita su tubi in ferro zincato o altro. Teflon su raccordi in PVC , ottone e altri raccordi con filettatura precisa.
@u_t_d_s_h-1_a
Жыл бұрын
What's the point using teflon tape -- if it is going just rumple-up, break and cannot stop leaks? Plumbers black silicone or pvc (don't know which anymore) tape ---works far more...
@lubomirlokos3474
2 ай бұрын
If tow is used for plumbing connections, it should not be greased, but left to dry!! If the wader finds a hole, the tow will soak up the water and seal it by itself.
@actionA06
2 жыл бұрын
If your going to pressure test that thing you better use both tape and dope , and don't use your bare finger , your just asking for a lacerations
@giancarlominardi2500
2 жыл бұрын
La canapa dei entrare bene nei filetti se no quando stringi il raccordo se ne viene tutta parola di tubista il teflin e fatto bene
@billnaire5220
Жыл бұрын
Hemp is better on galvanized connections.
@solidname9085
2 жыл бұрын
How much tape should we roll around pipe?
@shanemeikle5615
2 жыл бұрын
as much as it takes to stop the leak
@yeastyg546
2 жыл бұрын
75 yards apparently
@rednexican559
2 жыл бұрын
@@yeastyg546 🤣🤣🤣👍🏼
@frankiepezzolla
2 жыл бұрын
4 wraps
@shropshireladoutdoors743
2 жыл бұрын
Enough to fill the threads
@alehustle
2 жыл бұрын
Para eso vendían hilo grafitado o glicerina y litargirio combinados crean una pasta que sella durisimo
@RandyModdSteller
2 жыл бұрын
It was leak proof after the 6th rotation
@RandyModdSteller
Жыл бұрын
😂
@DrMrSmooth
2 жыл бұрын
Nice video mate 👍
@25rsimp
2 жыл бұрын
2.5 - 3 full wraps of PTFE is all you need.
@liquidsnake6879
9 ай бұрын
nonsense
@macp349
2 жыл бұрын
Wow, that seems like quite a build up for both
@davx_yz
2 жыл бұрын
and how is my expectation?
@VitorMadeira
2 жыл бұрын
Excellent video but AWFUL music. Ouch! 😣😣
@codykrueger796
2 жыл бұрын
The first half of it anyways
@stevenyangkun
2 жыл бұрын
PTFE is the best,even your hands is clean
@codykrueger796
2 жыл бұрын
I am guessing the hemp method is old tech
@Retro.Studio
6 ай бұрын
Cold water PTFE is fine, but on on warm water like your central heating use hemp with hemp grease
@patrixo8181
20 күн бұрын
Pod włosem nie daje się pasty😮
@wheelinndealin
Жыл бұрын
No reason to run tape all the way down the treads, it’s not like you are going to bury every thread when you tighten this nipple and if you do you’ll probably pop your fitting. Also super sloppy tape application, it should be uniformly and kept tight.
@user-zv1bu5py4m
2 жыл бұрын
Паклю лучше промазать казанским автогерметиком, импортные для этого подходят хуже - это 100% герметичность и никаких проблем в дальнейшем при необходимости откручивания.
@aneestahir8308
2 жыл бұрын
G nae d_seat kar ka na-ahal karna chahye tha
@the4thpossum329
2 жыл бұрын
The music sounds like auto tuned farts
@santehnikus
7 ай бұрын
Смазки много не быват😊
@user-ph2mt5qk9u
2 жыл бұрын
Лён так никто не наматывает. Это не правильно!
@user-yl8uh2ij1q
2 жыл бұрын
А ещё резьбу в тиски не зажимают.
@nathanbreon1021
2 жыл бұрын
Pipe dope
@amitpunjani1426
Жыл бұрын
I don't think if anyone who wants to learn plumbing etc will want unnecessary music in videos
@ivanjancek7893
2 жыл бұрын
The white tape is shit,,,, by steel pipe,,,
@ThatSB
2 жыл бұрын
Teflon way easier
@vjekoslav20
2 жыл бұрын
KUDELJAAAAA
@myogi6029
2 жыл бұрын
Masudnya apa oi
@user-zo4gz1vc3m
2 жыл бұрын
Если промазать Лен масляной краской то будет надёжно на десятилетия, проверено временем.
@user-uo8xk8ud6b
2 жыл бұрын
10 витков.
@arturtoficki7484
2 жыл бұрын
Japierdykam.... Taka prosta czynność a podstawowe błędy...
Пікірлер: 63