If you swung the rear suspension arm out of the way you would not struggle to fit the engine. You can then fit the driveshaft and refit the 2 hex bolts after. But great vid !
@jasondobbs7911
Жыл бұрын
Agreed - dropping the rear swingarm assembly out of the way makes the engine in and out a piece of cake - and it only takes a few minutes to do that. (you just need a really big socket and Allen wrench)
@keithbennett1359
3 жыл бұрын
Just a heads up on engine removal/install , the swing arm pivots are supposed to be removed so you can slide the swing arm / rear axle back to easily clear drive shaft u-joint.
@soulstitch18224
3 жыл бұрын
Mine just did the same glad you had same issue and pointed out how to fix it looks to be a simple fix just some long hrs to take engine out
@mustie1
13 жыл бұрын
nice vid, now your going to spend another $90 on grass seed,,,
@jasonb1761
5 жыл бұрын
Can you replace gears without removing the whole engine
@BigjermsGarage
13 жыл бұрын
@jasonmushersee Yes, just enough wear to cause a problem. We replaced the fork and the shift ratchet so I don't know which one it was exactly, but together the wear was the problem.
@jasoncoleman476
Жыл бұрын
Hello bigjerm I'm in the middle of doing the same thing on a phoenix that I had purchased but in your video you found a ball bearing in the bottom of the case I also had that bearing fall out when draining the oil where did that bearing come from
@BrianWhalen-s1l
Ай бұрын
The ball came from the spring loaded bolt that is a Allen key next to your drain bolt it to keep the bike in gear
@qapsukalek
7 жыл бұрын
There's a hose fitting by the starter where does the hose connect to from there ?
@airfox023
13 жыл бұрын
you think i could just weld that stuff together to get it to engage? i have the same problem with mine.
@larryminnifield2890
9 жыл бұрын
Thank you so much for sharing I have the phoenix and the same problem but now I think I can fix it
@markpaezjr1318
5 жыл бұрын
I have a head gasket on this bike that has blown can you do a video on how to install it thanks mark
@michaelgaris3309
4 жыл бұрын
Have a 200 four wheeler that won't stay in gear what is the problem
@jasonmushersee
13 жыл бұрын
So the fork was worn just enough it would'nt engauge?
@2305macleod
5 жыл бұрын
Hi you dont happen to have the part numbers? Thanks
@Mikebrook7810
10 жыл бұрын
were did you get your parts . just got a polaris phoenix for free and it is not going into drive . goes into reverse just fine but when it is in drive it jumps and you can here a grinding. any help would be awesome . i did subscribe. thanks for your time
@BigjermsGarage
10 жыл бұрын
Cheap cycle parts - Google them
@Mikebrook7810
10 жыл бұрын
awesome man . thanks for the fast reply . they have just what i need . thanks bro
@krzysztofgrudzinski3388
3 жыл бұрын
Where this steel ball should go?
@BrianWhalen-s1l
Ай бұрын
Goes inside the spring loaded bolt
@GooGun
3 жыл бұрын
I opened the transmission and bought the replacement parts but I have no idea how to remove the shift ratchet. Can you please let me know how you were able to replace it?
@BrianWhalen-s1l
Ай бұрын
Removed the Allen key
@jesusalmonaci6471
4 жыл бұрын
How much it cost for labor and parts
@zackhurley9148
4 жыл бұрын
Can you post the whole video all of it in a separate link? From start to finish I ended up taking the transmission case off but if I have to do it again I was going to take pivot bolts out also doing it by myself
@briangonzalez1101
2 жыл бұрын
Plz
@crapalator
8 жыл бұрын
thanks for your time.
@BigjermsGarage
8 жыл бұрын
No problem
@thomasgarvie6558
8 жыл бұрын
I am not too mechanically minded but I need to change the starter motor on my polaris phoenix 200 and i am not sure where it is and what it looks like have you any videos or photos that would help,when i was a lot younger i used to play with engines but it has been about 25 years since i touched a spanner
@TWM1122
3 жыл бұрын
@@BigjermsGarage I now have a 2006 sawtooth 200 auto, same as the phoenix with trans grinding when accelerating. There's small shavings in the oil. I've got the motor out and taken all the bolts out of the trans cover but still can't get it off. Am I missing something?
@CurtisHoltgeterdone
6 жыл бұрын
I replaced both shift ratchet and shift fork..all seemed great..but now at high rpm the shifter jumps out of forward..when the rpms drop it goes back into gear...any idea what I have done wrong?
@tatianagrieff6002
6 жыл бұрын
Curtis Holt did you find a solution? Mine is doing same thing
@trailpros4435
4 жыл бұрын
Did you figure it out? I believe it pops out because the little ball fell off the spring when you put the cases back together
@insectosaurus1
11 жыл бұрын
thanks for the vid i have the same bike and just fixed the same problem fall last year
@carminekira175
9 жыл бұрын
How did u keep the ball bearing in place when u put the cover back on
@rlourdes118
6 жыл бұрын
Did you happened to figure this out? Or I web page that could help me out?
@rlourdes118
6 жыл бұрын
Please
@airfox023
13 жыл бұрын
you think i could just weld that together for it to work again? i have the same problem.
@abrosius1
5 жыл бұрын
Did you end up welding this? We have replaced twice. I suspect the ratchet gear doesn't engage well because each time we have replaced the ratchet gear and fork they were barely worn on the forward gear side.
@TheSaltyGames
9 жыл бұрын
any one know how much it costs to get fixed at a mechanic?
@insectosaurus1
11 жыл бұрын
what kind of sound?
@aronomarortizruiz
13 жыл бұрын
my 09 phoenix have a sound when i acelerate on accidented terrain
Not Sure how you got this engine out without at least removing the swing arm nut on the drive side there was no other way this video is useless so many things skipped
Пікірлер: 49