Dyna polymer sand is the best sand! Great job guys.
@michaeljuers574
9 ай бұрын
Nice job but if you put it in 5 or 6 years ago it doesn’t seem to last a decade or more. 🤔
@teeb9969
Ай бұрын
I screwed up and left too much sand on bricks and I got sand still all over my bricks with sand
@Keramagic1
3 ай бұрын
Great video! We just had our old poly sand replaced 2 weeks ago. The seal wasn’t placed yet and we thought it was safe to give the pavers a wash, before setting down the seal. Unfortunately the sand washed out some of the paver joints and we’re going to have redo them. Will we have to take out all that sand again or will new poly work with what’s already there?
@CesarMartinez-tp4bx
Жыл бұрын
What’s sealant brand did you guys use ??
@rand49er
Жыл бұрын
After power washing our brick patio to remove weeds and moss between the pavers, I followed that up with a cleaning using a Zep cleaning product and a thorough power washing again. Yesterday, I broomed polymeric sand into all the cracks, used a leaf blower to lightly rid the surface of any remaining surface dust, then applied a nice misting of water over the entire surface. It's been dry overnight with no rain, and I have a great window of time this afternoon. Ques: Can I apply a sealer after only 24 hours of dry time?
@AamasonryCa
Жыл бұрын
Yes, you can apply your sealer 24 hours after.
@rajeshkumar27rk
4 ай бұрын
Hi A question, how much area did you guys covered and how much extra you guys charge for polymeric sand and sealing
@ryanreid1688
4 ай бұрын
Thanks! What kind nozzle?
@domenickmedia7871
Жыл бұрын
Is it worth trying to color match existing polymeric sand if you don't know which product was used? (5-10% got blown out when we cleaned our pavers with a pressure washer). Have you had any luck doing this, or should we completely replace the sand like you have done here?
@AamasonryCa
Жыл бұрын
No, new product won't adhere to the old. You have to remove the old polymeric sand completely by power washing, and make sure the cracks are fully dry before adding new sand and you need to tamp it again and again during the new sand application process so it makes its way down. You then brush off the excess, with a push broom so there’s no polymeric sand sitting on the stone, and then a light sprinkling of water (you can use a watering can or a light sprayer hose pointed upward, sprinkling down on the polymeric sand until saturated) for the best results.
@domenickmedia7871
Жыл бұрын
What PSI do you recommend for pressure washer to remove the old polymeric sand?@@AamasonryCa
@doomslayerforever2858
Жыл бұрын
Man that job must have cost 4k atleast way more then $2 sq foot
@ryanreid1688
5 ай бұрын
What PSI pressure washer did you use to remove poly sand from between the pavers? Was it cold or hot water system? Any concerns with damage to top of pavers from the pressure washer? Thanks!
@AamasonryCa
4 ай бұрын
The pressure washer is 3600 but the nozel depends on the pavers. cold water.
@AamasonryCa
4 ай бұрын
The pressure washer is 3600 but the nozel depends on the pavers. Cold tap water is what we use.
@UnderPressurePressureWashing
4 ай бұрын
@@AamasonryCadid you use any stripper? If so what brand?
@cuarto5748
5 ай бұрын
if so, you can't powerwashing the bricks anymore. powerwashing will remove plymeric sands
@shirleycarter465
Жыл бұрын
Hi! I replaced my polymeric sand 4 days ago and immediately it looked like it was peeling and it never set up. I used polymeric sand that I had saved from initial job 3yrs ago so I don't know if I added too much water or if the sand was too old. Can you tell your thoughts
@AamasonryCa
Жыл бұрын
Hi Shirley, Your result may be due to not removing enough of the polymeric sand by power washing or over saturated as you noted in your comment. A light sprinkling with a watering can is sufficient. If you are in the GTA region and require assistance with cleaning out the polymeric sand, this is a service we offer. Best, Corrine A&A Masonry 416-236-8721
@shirleycarter465
Жыл бұрын
@@AamasonryCa unfortunately I am not but your response has helped me figure out what happened. Thank you
@cpringle365
Жыл бұрын
@@shirleycarter465 that’s good to hear! Good luck, Shirley!😀
@JoshuaSkibinski
Жыл бұрын
What type of product is best for sealing? I assume the same as you’d use for stamped concrete?
@AamasonryCa
Жыл бұрын
There are many products with different qualities. Contractors usually have access to the best products through trade suppliers.
@CesarMartinez-tp4bx
Жыл бұрын
Can u please mention a few ? Thanks
@AamasonryCa
Жыл бұрын
@@CesarMartinez-tp4bx We get a commercially only available sealer but I believe Home Depot has many sealers to choose from. Not having experience with them I can’t really recommend one over the other.
@CesarMartinez-tp4bx
Жыл бұрын
@@AamasonryCa here in Ct some of us have access to commercial companies that sell to homeowners which is why I asked about sealers/brands you would recommend.. I will be avoiding the local box stores by all means ..
@AamasonryCa
Жыл бұрын
@@CesarMartinez-tp4bx our supplier is a local manufacturer here in Ontario who creates products for our environment. Perhaps you can find someone similar in your local area.
Пікірлер: 29