Thank you. Thank you. I appreciate you saying this applies to Hayward also as this is my filter. Have a refreshing summer!
@truelightpoolsllc4441
Жыл бұрын
Sure thing, glad to help.
@Will-ik3sz
2 жыл бұрын
I have a good one for ya, why does mine on my TR60, backwash when the t handle is down? I run in filter mode, with the handle up. Is there an issue with mine?
@truelightpoolsllc4441
2 жыл бұрын
Yes, many large sand filters run their filter valves the way you describe, up is filter mode and down is backwash. Not sure why, but it's that way on commercial valves. Maybe it's just the way they plumb it.
@MrMusic55123
2 жыл бұрын
I left it in the backwash position for several month and it's now rusted and don't to push inside, any idea on how to fix?
@truelightpoolsllc4441
2 жыл бұрын
see if you can spray WD-40 in the chamber to move the piston up and down. If you can't get the piston out, you may have to replace the whole T valve assembly by plumbing in a new one.
@Jay-bi8kn
11 ай бұрын
Is it necessary to lock this pull-push valve? Mines pretty stiff so I just pull and push when backwashing
@truelightpoolsllc4441
11 ай бұрын
It's usually fine to do what you are doing.
@zazarays
3 ай бұрын
Thx
@truelightpoolsllc4441
3 ай бұрын
No problem
@TrevorLashley-bl6ji
2 ай бұрын
Mine shoots sand back into the pool after a backwash do you know what I’m doing wrong
@truelightpoolsllc4441
Ай бұрын
Probably something is broken in the filter.
@DavidPerez-bn6vr
2 жыл бұрын
How do I change the T-Handle? Mine broken as I was turning it.
@truelightpoolsllc4441
2 жыл бұрын
Have to unscrew the middle screws that are holding it in and pull piston assembly out, then replace complete middle piston assembly.
@KENPACHI1K
2 жыл бұрын
Order part on Amazon. Take out metal pin, replace, put metal pin back in
@truelightpoolsllc4441
2 жыл бұрын
@@KENPACHI1K Yes if just the handle part.
@FairySkyler
Жыл бұрын
I don’t have a push pull valve but nice video
@truelightpoolsllc4441
Жыл бұрын
Thanks!
@sallyville3442
2 жыл бұрын
How can i vacuum to waste with that valve?
@truelightpoolsllc4441
2 жыл бұрын
You can't exactly, the 2 positions are only filter mode and backwash mode.
@DFWJon
2 жыл бұрын
@@truelightpoolsllc4441 So, I’m assuming that you can NOT remove the filter (not physically removing but just bypassing the filter) from the system by changing the setting and just recirculate the water with a slide valve??? I would need a multi-port valve in order to do that, correct??? Thanks in advance.
@truelightpoolsllc4441
2 жыл бұрын
@@DFWJon That’s correct, it’s filter mode or backwash mode with a slide valve.
@Will-ik3sz
9 ай бұрын
What I did was remove the top on my TR60, removed the diffuser, made and installed a ELBOW that threads onto the pipe the diffuser was threaded on, and extends above the top of the filter, then attached my backwash hose to that elbow. Feed the hose out to my alley, and then hook up my side port hand vacuum. Set it to the side port, and put the slide valve in filter mode and vacuum. Water comes out the hose, dirt and all! Works great, just a pain to have to do it this way vs a multi-port valve.
Пікірлер: 23