Thanks Julian sooooo much for your brilliant 'easy to follow' video. Went onto eBay bought refurbished Suprima 70 controller (£110) and arrived, fitted, hey presto - warm showers and heating now back in the house. 10/10. Orrrabest - Tam fae Glesga :)
@johnnydxxx
2 жыл бұрын
Thanks Julian, Ordered refurbished one from Ebay. Came next day, 10 minutes to swap out and boiler fixed. Saved me a fortune. Cheers!
@michaelgolf6941
Жыл бұрын
Brilliant explanation of how the Suprima boiler works. Even if your not a DIY guy at least you know what the heating engineer charging you for. It's best to have an understanding of your system when making decisions that will cost you money. Well done and thanks for the video.
@Neo-mw1pp
Жыл бұрын
Have my Suprima 50 now for 20 years, in that time ive replaced the PCB 7 years ago and the cast iron heat exhanger that rusted from the inside out about 4 years ago from not cleaning the system. I drain the system now every year or two pre-season and add new inhibitor. I expect another 10 years plus out of the old girl yet, great boiler!
@tonyhealey8977
Жыл бұрын
Good fix at a good price. I have a suprima 70 that failed. I re soldered all joints on the circuit board which cured my fault. I read that they reduced lead content in their solder which caused dry joints.
@michaelnixon4856
2 жыл бұрын
Concise well explained and useful video with exactly the same error as on my potterton suprima 40. Now off to order the exchange PCB 😄👍
@godfreydesilva5222
2 жыл бұрын
Excellent video. It does give a message how to check the boiler. Thank you.
@Thereishope664
8 ай бұрын
My Potterton Suprima is like Triggers broom. Three fans, two igniters, I air switch, I heat exchanger. But no PCB. Its 19 years old and going like a train.
@jagjitghattaure1670
Жыл бұрын
That was a brilliant demonstation of the problem. I am having the same problem with my boiler. And would be so please if someone could help me sort it. I thought it's the pump so I have purchased the pump. And wish to fit a magnaclean too and change the two valves.
@tokomac7728
2 жыл бұрын
Yes it is working…what about safety devices in an case of flame loss in an case gas valve still open ….as trained gas safety people we must check flame rectification device is it putting boiler in safety locking mode (red light)????!
@TheAngryengineer
Жыл бұрын
"And worst of all, it's Didcot"?? How very dare you?! 😂
@peterstubbs5934
2 жыл бұрын
Good video although I have the opposite problem.. Intermittantly (but often) the boiler stays ON and wont switch off, obey the thermostat or the timer. The only way I can stop it boiling us alive is to switch off the power to the boiler.
@karimachandler2409
2 жыл бұрын
i have the exact same problem - did you get anywhere with yours? Thanks
@doitcom
Жыл бұрын
Hi Peter. I'm having a similar issue. The boiler is turning on randomly and heating the house and ignoring my HIVE completely.
@gingerrussell
Жыл бұрын
I think I had the same issue. Went out and heating stayed on all day. Ended up replacing the motor switch thing located above the pump. Seemed to do the trick. Product code 76959 on Screwfix. Old one was stuck open.
@doitcom
Жыл бұрын
@@gingerrussell my boiler went pop on Friday. So new combi being installed currently :(
@Paul-ys8wg
2 жыл бұрын
Great vid ...thanks what company did you use on ebay. I have similar issue on suprima 40 and looking at the advanced exchange service on ebay. thanks
@julianjones7914
2 жыл бұрын
Hi. Thanks. It was Adlink UK. Rgds
@mikeahern3999
6 ай бұрын
Thank you that was excellent.I have the exact same boiler and much the same problem could you possibly give me the name of the company you purchased the unit from .Thank you ,much obliged. Mike
@lemonhead113
Жыл бұрын
I have a question. My boiler seems to be on alllll the time. Why is that? I want to cut my gas bill. Do I just turn it off when not required?
@as33edsnwnw
2 жыл бұрын
Hi Julian, I think I have the same problem, please would you tell me how. An I get mu module repaired as you did? Many thanks for your video
@garryhills8648
Жыл бұрын
Yes mine was pcb there a man on eBay who solders joints With lead solder as manufacturer doesn’t use lead solder
@dukedepommefrites8779
Жыл бұрын
Thanks Garry, why is lead solder important? Pls could you say who you used. TIA
@garryhills8648
Жыл бұрын
@@dukedepommefrites8779 Hiya it’s because the solder is not strong and cracks and the board has intermediate Issues. He also bridges it too. I will have a look on eBay for you Regards Garry
@garryhills8648
Жыл бұрын
Hiya I have found him on a email
@dukedepommefrites8779
Жыл бұрын
@@garryhills8648 Many thanks Garry, ordered a refurb now.
@garryhills8648
Жыл бұрын
@@dukedepommefrites8779 great news I fitted that ten years ago never had a problem I had to change the fan housing quick easy job £70 and a year warranty all working great and no problems
@margiemcgillivray5063
Жыл бұрын
Thanks. It worked for me👍
@Moodymongul
2 жыл бұрын
I have this exact boiler. Can anyone tell me how the cover should be opened (where the fan is located). The boiler I have here seems to have a cover thats been wielded on by the last guy ;) I just wanted to check the 'correct' way to remove (there are no screws showing on the cover) Thanks
@Moodymongul
2 жыл бұрын
np. figured it out. You have to remove the outer casing, surrounding the pcb assembly, first. Doing that, gives you access to the two screws that hold the main cover in place (the cover that hides the fan etc)
@moolindabumble9251
2 жыл бұрын
Mmmm my plumber changed the PCB board and it still isn’t working. It flashes amber green, keeps clicking and then flashes red. It’s very, very annoying. 😭
@user-yw6qb9tt7t
Жыл бұрын
Could be the pump. My pump went. They have a shelf life. The boiler fires only for about a minute and the heat just reached the pump but as it was not being pumped and circulated the overheat thermostat on the boiler operates and stops the boiler from boiling as the heat is not going anywhere where it should and the boiler senses this and will overheat hence the name of the safety device. Overheat thermostat.
@toffmcman9505
Жыл бұрын
Changed my pcb as well but still turn in and goes off after couple minutes, I guess is short cycle tho . Pump working fine as there is no noise and I can hear the water circulating in the system , some I hear airbuble sounds I did bleed the rads but it’s still has same problems
@ronnieroo227
Жыл бұрын
Dear wonderful Potterton gentlemen, l have been told I need to check my water pressure on my Potterton Suprima boiler? I told him there isn't a visible one, could you please tell me where to find it? (PCB board easy enough, l have done 3 on our 20 year old boiler) .
@andyliv78
Жыл бұрын
There isn't one. It's not a combi.
@user-yw6qb9tt7t
Жыл бұрын
If the system is unvented meaning an expansion vessel has been installed in place of the loft header expansion and central heating feed tank the system will have a pressure gauge installed but separate from the boiler.
@garywilson6047
Жыл бұрын
Which seller was it you bought the pcb from? Thanks.
@theeroom
2 жыл бұрын
Question: can I increase the boiler flame to heat up the house quicker? Or is there risk in causing issues
@ronnieroo227
Жыл бұрын
Yes, it's a screw type fitment right at front under the second screwed closed cover. Our engineer did it after fitting new gas valve.
@dukedepommefrites8779
Жыл бұрын
Hi Julian, many thanks for the video. just wondering how the PCB is behaving after a year? Our boiler is 20 years old, ok til recently, would you know why these faults start to occur over time, believe faulty soldering is an issue but why only shows up after say 20 years.?
@dukedepommefrites8779
Жыл бұрын
Glad to hear. Spoke to a gas engineer across road, he says not worth upgrading to new condensers. Apparently not serviceable, the old pottertons etc can nearly always be repaired.
@gregchrisp2177
2 жыл бұрын
can you make a video on how to put into service mode please
@julianjones7914
2 жыл бұрын
Sorry, Im too busy to do that at the Mo!
@mechtechmechanical1571
Жыл бұрын
common knowledge in the gas world that the pcbs fail
@user-yw6qb9tt7t
Жыл бұрын
On these boilers which are great otherwise
@chriswareham5763
Жыл бұрын
It is against the law to remove anything from the boiler you must be gas safe registered It’s there for a reason!
@ravindersidhu9417
2 жыл бұрын
You have to be gas safe to work on boilers
@julianjones7914
2 жыл бұрын
My understanding from 2019 regulations is that you can carry out work on your own boiler providing you do not interfere with the gas carrying components! Furthermore, the last gas safe operative that did work on my gas boiler left it in a very dangerous state- so beware who you employ even if they seem to be qualified!
@sambda
2 жыл бұрын
Only on the gas side - you can fix the electrics yourself.
@travimad123
2 жыл бұрын
@@julianjones7914 Do you have a flue gas analyser? Checks need to be carried out to meet Regulation 26.9 when work carried out on boilers.
@julianjones7914
2 жыл бұрын
@@travimad123 I don't touch the gas so not relevant!
@nikolayginev
2 жыл бұрын
@@julianjones7914 The regulations state that you cannot remove the front cover of the Boiler if you are not qualified Gas Engineer.
@leightonedwards1322
Жыл бұрын
Shouldn’t be taking the cover off the boiler you have to be gas safe registered, read the regs, if the cover is not correctly fitted back on it will be in safe, another thing is you can’t test a pump by putting mains to it, how can you tell if the propeller is working? Is is why we spend thousands of pounds of course to be qualified! Leave to the experts and come of giving people advice, you will cause a major problem
@user-yw6qb9tt7t
Жыл бұрын
TBF he did not touch the combustion chamber. Wiring in mains to the pump was a temporary test to see if it worked. It was obvious it worked as hiw would the system have stayed on at all if it didn't as the overheat thermostat would have stopped the boiler working fairly promptly if it didn't. You have to wonder what advice the well qualified boiler servicer gave though !
@hoppy1970
2 жыл бұрын
Unless you are gas safe registered, it is illegal to "disturb a module that controls the combustion process". I believe it's a maximum of £15000 and two years in the pokey. I suggest you delete this video.
@julianjones7914
2 жыл бұрын
I can only guess as to why your comments are so incorrect and misleading! If you contact GasSafe, they will confirm that the work I have done is perfectly legal!!
@RoobieRoo2
2 жыл бұрын
@@julianjones7914 Again you are correct. If the work required only involves the replacement of a non-gas component such as a water circulating pump or central heating control valve, housed within the boiler’s decorative casing, the work could be undertaken by another competent tradesperson e.g. plumber/electrician. Providing the work could be undertaken without having to break a combustion chamber seal!
@garywilson6047
Жыл бұрын
@@julianjones7914 Hi. Can you remember which seller you purchased the pcb from please. Thanks.
@user-yw6qb9tt7t
Жыл бұрын
All electrical work except Part P work which is basically Bathroom and then in the zones, consumer unit changes and new circuits can be conducted by anyone as long as they are competent. This bloke sure is.
@hoppy1970
Жыл бұрын
@@user-yw6qb9tt7t This is NOT electrical work as per BS7671. Any component that affects the combustion process must ONLY be worked on by a gas safe registered engineer. In the case of the control module, Regulation 26(9) MUST be carried out after replacement. I am a gas engineer since 2011 and electrician since 1990. Thanks.
@cowardsallaround98
2 жыл бұрын
Do yourself a favour and get a new boiler and watch your gas usage go down A 1995 boiler is a danger 26 years old are you sure
@Neo-mw1pp
Жыл бұрын
Incorrect.
@user-yw6qb9tt7t
Жыл бұрын
These boilers and the cylinder system are work horses and rarely malfunction and then it is a simple fix. We spend more money fooling with combis and servicing over their life span. Boilers have become like cars. Leave it to the experts so they can mint it
Пікірлер: 75