6 yrs later, this video is still helping us in the trade advance ourselves.
@olinzuercher6344
5 жыл бұрын
As an amateur who's never had much instruction, I find this kind of video to be very helpful.
@joepie221
5 жыл бұрын
2 step indication is the only way to be sure you have a good part if you have to flip it.
@toddanonymous5295
8 жыл бұрын
Joe, I don't know what is more valuable, your exceptional teaching ability or the great hints you give all of us. Thank you so much for sharing your skills with us.
@joepie221
8 жыл бұрын
My pleasure. Thank for the feedback.
@susanss70spartymix77
6 жыл бұрын
I always thought his background music was the best.
@oddjobbobb
4 жыл бұрын
So so true!
@kennethnevel3263
3 жыл бұрын
Some people take their knowledge to the grave and never share it and it is lost . You share it and people learn from it and take it to the next level and do better work .
@walterkoepisch
7 ай бұрын
😊😢😮😅😮😮
@MichaelLloyd
7 жыл бұрын
I'm only a hobbyist but I am very appreciative of that instruction that you give. Clear and concise. Can't beat it
@johntenhave1
4 жыл бұрын
I have owned and operated a lathe for more years than I care to admit ( ok 50 yrs...) and you taught me something i had never considered and something I never knew. Thank you Joe.
@joepie221
4 жыл бұрын
Thanks for watching.
@jimmilne19
8 жыл бұрын
Absolutely clear instruction, and I'll be doing these checks from now on every time. You are a fine educator and as a new machinist I so appreciate you sharing so freely what you know. And, what great topics, so very useful. Thanks Joe for this one too.
@joepie221
8 жыл бұрын
Glad to help Jim.
@loneflwolf
6 жыл бұрын
sorry does this work no response
@timclayton9038
4 жыл бұрын
Thank you Joe love you videos I’m putting them in a folder for when my grandchildren are old enough to want to learn, I so hope they want to be craftsmen. TC
@christopherruble3913
6 жыл бұрын
I trained as a machinist 40+ years ago and am still glad that I found your site, as well as Stan Zinkowski's and Dale Derry's. I am learning a ton of stuff from you guys that I never learned back then. Keep up the great work, Joe!
@jeffryblackmon4846
7 жыл бұрын
Once again you've explained more than I realized there was to learn. THANKS!
@stevejackson5062
7 жыл бұрын
School trained but never worked in the business so I'm dumb as a rock. Have a well equipped hobby shop and am learning more from your instructional videos than I did in 2 years of night school. Can't thank you enough. Wish I was closer - I'd sweep your floors.
@EarthSurferUSA
6 жыл бұрын
I know what you mean. I got out of school (for the first degree) and got a job, quickly learning I did not know much. 20 machine shops later, I found out my last 5 bosses did not know much. :) Self employed now, and loving ever second of it. If you do want to get a job, (treat your jobs as a education you actually get paid for), I advise 2 things to accelerate your learning a great deal. 1) Never get a union job. In manufacturing, they have less skill than you do now, and never get much better. Can't start your won business that way. Today, because the talent pool is shrinking, non-union jobs are paying more than they ever did, but don't expect good pay until you have the experience. 2) The best place to work and gain skill is a "Job shop" where they work with a lot of different kind of materials and processes. The job shops are were the union shops send the more difficult work in many cases. You can learn some things with high volume production, but a job shop, you are doing something different every day, (usually). They can be tough to work for, but after about 3 shops, you will gain the skill to be able to be attractive to any shop who is hiring. I was a "job hopper", and that is often looked down upon, but most people looking for a new job were not "lifers" at any shop, so that is the choice a employer has. I earned some sill at ever job I had, (and thankful they all hired me,---even when I got fired; big mouth usually), but I earned a ton of skill working for any shops. Now my hobby turned into a business, and my machining skill set me apart from almost all of my competition, (modifying small gas engines for racing). I have to tell you,---it feels great making more money than any union worker in the world. :)
@commanderboom206
6 жыл бұрын
nice to see you around Doug
@aquilifergroup
4 жыл бұрын
I’d help sweep too. Thanks
@richardallred4243
8 жыл бұрын
Last year I purchased a1984 lathe from a friend,s wife after he developed mental issues. I am self teaching with the aide of You Tube postings as he is unable to help me with any of the basics. As such I have been struggling with some of the runout issues you describe for over a year. I was thinking I had twist in my ways. I have checked and re-leveled and checked again and again using plumb bob methods and precision levels. It would look perfect but I still had accuracy issues with a thru hole not being centered on the back side. After seeing this video I feel certain I can make it work properly. I plan to watch all your postings and am certain I can learn much from you. THANK YOU The light has finally dawned!
@joepie221
8 жыл бұрын
Thank you Richard.
@okaygotit6509
6 жыл бұрын
Great video! I've been a machinist for about 20 years now and this is a very good way to show somebody that's coming up in this trade how to think about late work critically.
@georgebear4557
5 жыл бұрын
Who are these 27 people who dislike your video? What's there to dislike? Your instructions are simple and concise. I was about eight years old when I first worked on a lathe. I'm fifty-two now and you still have shown me some techniques that are new to me. Fantastic channel. Please keep up the good work. You are an inspiration. Bet those twenty-seven people don't know what a lathe is, let alone made a video for KZitem.
@HaqqAttak
5 жыл бұрын
27 people bumped the dislike with their hand without knowing it on their phone.
@chrisbuschendorf3155
4 жыл бұрын
Joe, i went to a trade school as a high school back in the 80's went through an apprenticeship and got my mold making papers. Before the Internet a trade school was the only place where you could learn the things that you are teaching. I wish that I had the opportunity that people have learning from the lessons that you are teaching. Your doing a great job and providing a good service to the young ( or old) people learning about machining. Keep up the good work
@bozo28able
3 жыл бұрын
Joe I have seen so called machinist's who have run lathes for over a decade who didn't know or understand what you just explained. They would remove a 4 jaw chuck and bore soft jaws on a 3 jaw chuck for a 1 off part. I have almost 50 years in the trade and I am really glad to see you teaching the trade. Thanks!
@joepie221
3 жыл бұрын
Happy to do it.
@stoffel89
6 жыл бұрын
Best advice ive been given in a looong time. Will never forget it and allways use it. Not all are willing to share their advice. And those stupid enough not to follow good advice and share it even more are not making the world any better. Thanx again. Your videos are awesome. Wish i had a machine shop... One Day. Maybe...
@StuartsShed
2 жыл бұрын
Joe, I just used this technique today - I was going crazy trying to get a part true - making an offset bore through a part. Well, the bore axis I was starting with was not parallel to the OD of the part. Happily I had stock left, so I trued the face, clocked the length of the OD as a check and then bored the hole. Fixed - thanks for making all this info available.
@martinwhittaker9860
6 жыл бұрын
Joe I’v said it before ,but I have to tell you I have spent 50 years in engineering and trained as a toolmaker in the U.K. and just love you videos and learn or maybe relearn. So much from you. You’re manner of presentation is superb. SO PLEASE DO KEEP YOUR VIDEOS COMING I’m just one of your many grateful viewers. Martin from the U.K.
@geoffbrumpton8544
4 жыл бұрын
Thanks Joe, I don’t have the time to reinvent the wheel so I find a few minutes watching your videos is a huge time saver for this lathe novice. 👍
@joepie221
4 жыл бұрын
Glad to help
@steventhompson3507
Жыл бұрын
Following your video on thread cutting in the lathe away from the chuck enabled me to improve my thread cutting so much. Cheers Joe
@joepie221
Жыл бұрын
Great to hear. Its a good technique.
@boydmason4476
7 жыл бұрын
I am a professional engineer in my 50's who bought a lathe and mill and other machine shop equipment to learn machining and take it up as a hobby before I kick the bucket (also I've grown tired over the decades of hearing the trades tell me how little engineers know). Your videos are making my new hobby incredibly enjoyable and saving me a lot of frustration. Thanks Joe.
@joepie221
7 жыл бұрын
Thanks for the comment. Ask a question if you hit a wall. I'll answer you.
@takedeadaim8671
Жыл бұрын
I’m getting some of these earlier videos in my feed, always great reminders. I do special purpose tubes with a spiral hole down the middle the OD has to coaxial to the hole as does the threaded feature on one or bot ends. In addition to that the faces on the ends must be perpendicular to the hole. They are long so I either use a thin shop made chuck on the outboard end of the spindle to help support and align the job. A precision ground rod with various bushings are used to “reach “ down the hole from both ends create additional points to indicate. I might take a jump into this and make a video of the process. This set up can take some time as toy showed where you adjust in one point it affects another.
@AnthonyGriz
4 жыл бұрын
I've decided I don't need a therapist anymore, just need to watch more of these videos! Thanks Joe, another awesome video, and greatly appreciated!!
@joepie221
4 жыл бұрын
Glad you like them!
@HanstheTraffer
6 жыл бұрын
I just bought my first lathe. Haven't operated one since high school 50 years ago. Thanks very much for sharing. I plan on watching more of your videos.
@joepie221
6 жыл бұрын
Feel free to post questions. I'll answer as time permits.
@BillyTpower
8 жыл бұрын
Holy Crap Joe, you just turned a light bulb on for me... I think.lol... last week I was drilling then boring a 4" piece of 1" od stock. I could not figure out wtf was going on because the bore was oversized on each end but tight in the middle... I now think I know why.. Thanks man, you rock
@t.l.c.5510
6 жыл бұрын
Finally, a video that makes sense. Much appreciated
@roadshowautosports
Жыл бұрын
This a subscriber from the future thanking Mr. Pie for this video 6 years ago!!!!
@Spurioushamster
7 жыл бұрын
Seriously some of the best lathe advice I've heard. Great video.
@johnbrink53
6 жыл бұрын
Thanks for doing this for everyone!! So many teachers right now don’t show anyone anything ! They tell everyone to look it up.
@RumpLeINtiLINsKinnIN
8 жыл бұрын
Just found your channel. I must say it is one of the best machining instructional channels on youtube(and I watch them all!) The way you explain things and give the reasons WHY you are doing something instead of just saying "DO THIS" is great. Your explanations just click with me more than other channels. Thanks
@joepie221
8 жыл бұрын
This kind of comment really makes my day. Thanks for watching. Feel free to ask a question if one comes up.
@colibriguitars
3 жыл бұрын
Come on Joe!!!! i really like to learn a lot of stuff, last year a learned a little about drawing plans whit Rhino... i like to learn watching tutorials.... But your videos are the best tutorials ever!!!! me, as a craftman (i´m a guitar builder) there is some people that ask to teach them... i always say: what do you know about? they say "nothing"... i ask Why?? becouse there is no info anywhere..... Sucks! if someone really wants to learn something there is a lot of info around in this time!!!!! and your videos are some of those GREAT resources to start...... i got a mini lathe 3 years ago, because i wanted to learn.... and looking the right info is the best time spended about... now i can make an Internal combustion engine that runs... and your videos are simply the easiest way to learn! thanks again for all the time you spend.
@AlecSteele
6 жыл бұрын
Awesome info!!
@mrdavidurquhart
7 жыл бұрын
I have so much respect for you and your experience Joe. Thanks for caring about the trade so much that you make a real effort to share with another generation.
@ninalli
7 жыл бұрын
Hey Joe, my no.2 son and I have been watching your films with great fascination. Although I am a pharmacologist of 30 years my real passion is engineering especially as a boy and now as a older man! Being brought up by a grandfather who was a clock maker gave me the interest in engineering. My engineering ambition is to complete a model live steam loco (5") and watching your films has very much given me the understanding I need to work my growing workshop of old but still good equipment. Please keep the films up, we are finding them really great and hugely educational. Thankyou for all your efforts. Dave and Family, Kent UK.
@joepie221
7 жыл бұрын
Hey Dave. Great comment. Thanks. 2 guys you should also check out are Mr. Crispin and Chuck Tipton. If you need a little more inspiration for your project. I'll get off the gun stuff for a while and get back to shop videos, but I do appreciate you guys hanging in and allowing me to check that off my bucket list. Got some good stuff coming. Thanks for watching. By the way....I did my apprenticeship in a company that specialized in precision miniature components for the watch industry. I worked in the toolroom and built positioning fixtures for secondary operations. The parts were so small, a days production would fit in a pack of smokes and had to be weighed to be counted. A 100 parts would stick to the tip of your finger. I've been into fixtures and prototypes ever since.
@tonythomas951
6 жыл бұрын
You are very good! Some people have an ability to convey knowledge and teach and you Joe are one of them. Thank you very much for doing so. You have no idea what a help you are.
@joepie221
6 жыл бұрын
Thank you, Glad to do it.
@patlaird4188
7 жыл бұрын
Joe. I wish I lived in Austin. I'd be at your door everyday begging for a job. My company is so half assed. Thanks for showing how real work is done.
@joepie221
7 жыл бұрын
Thanks for watching.
@BobJones-cr1pl
7 жыл бұрын
Check the shoulder, check the shaft. Get the shaft round , recheck the shoulder, recheck the shaft. I machine on an arbor that I do that on EVERY time. If you don't, sooner or later you'll be in trouble. Excellent video and instruction. And as usual Joe , absolutely right.
@joepie221
7 жыл бұрын
Thank you very much. Gotta have square and concentric for a good part.
@jimnicholson4509
5 ай бұрын
Thanks for that Joe ,now I realise how concentricity can be so tricky, that explains why I had some problems with clock arbors not running smoothly, so your video was much appreciated, thanks buddy. Jim from Australia.
@joepie221
5 ай бұрын
Glad to help Jim.
@ajwhittlebang6977
4 жыл бұрын
I learned to keep halving the error on the DTI until true and worked out over lots of years that concentricity of cantilevers takes the method you explain so well in this video. Have seen some immediately go for 0 and not be able to establish truth as DTI keeps bouncing. Great video as always.
@joepie221
4 жыл бұрын
Thanks. Its good to get a understanding of whats going on.
@bigalremington
3 жыл бұрын
Thank you, thank you! Great stuff, ....a new-bee here. And I thought building homes was something difficult in keeping the numbers correct. I love this new world of making metals fit. Yessah!!
@alfreddeltrecco8987
7 жыл бұрын
have a little home shop now been out of the areo space shop 25years and all i see you do i give you two thumbs up keep it up good job!!! AL
@jimmyjones001
7 жыл бұрын
I have to say this is outstanding information for everyone! I work at a shop that is all CNC machines but these principles definitely apply! A lot of people don't understand what "running true" really means. thanks for the video.
@keithrussell8778
7 жыл бұрын
Another great tip Joe, I am self taught, but tips from pros like yourself really help, once again many thanks, Jack from across the pond
@Jason710.
3 жыл бұрын
Glad I saw this as I wasn't told about whip that I can remember, I may have just forgotten since it was so long ago and just recently got back into machining, either way I appreciate it and thank you joe.
@mrc1539
3 жыл бұрын
That’s an awesome tip that is so easily over looked. Thanks for the reminder.
@slartybartfarst9737
4 жыл бұрын
Joe always watch your channel its gold dust, thank you brilliant craft teaching again.
@gregoryphillips142
6 жыл бұрын
Joe, I want you to know that your effort making these videos makes a difference in my life! I work as a machinist at a shop with old clapped out machines. By using the techniques you demonstrate I make less mistakes and work faster, daily.
@joepie221
6 жыл бұрын
Thanks for the message. I was fortunate enough to align with some tough but very talented guys early on. I'm glad to pay it back.
@razorworks9942
7 жыл бұрын
Hey Joe, I've been a welder/Fabricator (Union Ironworker) for the better part of 40+ years now, but definitely a newb when it comes to machining. Even though I've made some pretty cool things, and fixed a few parts, calling myself a "machinist" is a far cry from that title. Sharing these tips like you said "learn the correct way from the beginning" and you'll make better parts from the Gitgo! I couldn't agree more. Same goes for my trade, just because someone sticks to pieces of metal together with a welder doesn't necessarily make you a "welder"! Thank you again Joe, you are appreciated by a lot of us out here..Especially me. Razor!
@joepie221
7 жыл бұрын
Thanks Razor. Always good to get a comment from you.
@thevideoboy87
6 жыл бұрын
Joe, not sure you're reading this more than a year later. I'm just an electrical engineer and I understand what you said. Just want to say that this is very useful and I will show it to all the guys in our machine shop. Keep posting such great content!
@joepie221
6 жыл бұрын
Thank you. I appreciate you spreading this content around.
@thosoz3431
8 жыл бұрын
Focused , concise and clever, nice. Thanks Joe.
@joepie221
8 жыл бұрын
Thanks Thomas
@desertforgeknifetool2142
7 жыл бұрын
Joe, cant thank you enough for these jewels of wisdom !!!!!! They are taking my accuracy to a new level.
@joepie221
7 жыл бұрын
Outstanding. Take it and make it better.
@niklnikl1
6 жыл бұрын
Thank you Joe! This is something I would have never thought to do. I owe a lot of gratitude for your great educational videos.
@crazymanmichael8386
7 жыл бұрын
just another newb enjoying learning the right way to do things. younhave a freat selection of topics and as others have mentioned, you are a damn fine teacher. please keep it coming!!!!
@Klystron33
5 жыл бұрын
Hi Joe, thanks alot for sharing your knowledge and ideas with us, it's greatly appreciated! Best regards from Germany
@charlesbrewer6552
8 жыл бұрын
Thanks so much for doing these videos. There are a group of you guys doing this stuff, and it ranges from beginner to advanced stuff. It is all GREAT for us home, self taught "would-be" machinists. You guys show us stuff that is "not in the books" and is invaluable knowledge for what seems to be a dying art in the western world. Thank you so much! I put the information given by all of you to use All The Time. Constantly building my knowledge.
@joepie221
8 жыл бұрын
Thanks Charles. Put safety at the top of that list. Make sure the jewelry is off, roll up the sleeves and wear those glasses. Good luck with your projects. feel free to ask me questions if you have them.
@themoose2350
7 жыл бұрын
I am new to machining. I took a job at a fabrication shop that makes large animated water fountains across the U.S. I have only ever used a brake lathe a drillp ress and a bandsaw. I find your videos educational and helpful thank you for sharing your knowledge and experience with us just starting out. better to learn right then try to undo bad habits.
@joepie221
7 жыл бұрын
Agreed. Thanks for watching
@davidjames1007
Жыл бұрын
Thank you Sir, you taught me something today, I am just a hobby machinist but this will help a lot.
@chilavere8974
3 жыл бұрын
Amazing machinist ! Congratulations from France
@joepie221
3 жыл бұрын
Thank you very much!
@swelschwraith
6 жыл бұрын
this is the kind of stuff I wish they showed me in School.... Tips and tricks of how to do things. What habits to establish and which ones to break. THANK YOU FOR SHARING AND KEEP THE VIDEOS COMING!
@speedbuggy16v
6 жыл бұрын
great video, I have seen more than a few people on youtube mess this up, and measuring taper incorrectly. Thanks for taking the time to show us the correct methods!
@jackbonanno8186
2 жыл бұрын
Amazing, you got me on that one, I must have been asleep on that one. Makes so much sense. Thank you. Making notes of that.
@jeremysmith1339
Жыл бұрын
You are an absolute resource sir!
@joepie221
Жыл бұрын
Glad to help.
@hamedhashemi7951
3 жыл бұрын
You are great. love and appreciate you from Iran. 🌹💚🙏
@AtelierDBurgoyne
8 жыл бұрын
Very well done. Short and to the point. Love your presentation style. Daniel
@joepie221
8 жыл бұрын
Thanks Daniel
@trevorlee7945
Ай бұрын
Great lesson learned thanks Joe I never would have guessed that the face could be out of square if the shaft was indicated true .
@joepie221
Ай бұрын
Glad to help
@starfishten
8 жыл бұрын
Thanks Joe the short but very informative section is a breath of fresh air ,also watched the section on tool height to centre was always shown to measure from centre of tail stock or a little bit down ,what u have shown me hear has saved me a lot of head scratching and aggravation as to why i couldn't get my work any better ,thank you so much.
@joepie221
8 жыл бұрын
This step is a giant step towards a better part. Good luck and thanks for watching.
@richardmorton1310
4 жыл бұрын
Joe, love your video even they old ones. Just an old homegamer and your videos have helped me.
@X19-x5f
8 жыл бұрын
Lots of good info. Had to watch the vid a few times and think it through for a while, but now I understand perfectly. Great video Joe.
@joepie221
8 жыл бұрын
Thanks for watching.
@MrMarcaap
6 жыл бұрын
Very clear and concise instructions. Thanks so much for taking the time share these nuggets of wisdom and experience.
@fukcg00gle95
3 жыл бұрын
I've learned so much from your videos. Tyvm
@joepie221
3 жыл бұрын
Glad to help
@gweliver
6 жыл бұрын
Great information, just starting as a hobby (59 yrs old) bought Craftsman 12”x36”, and now a subscriber to your channel with “alerts” on too!
@joepie221
6 жыл бұрын
Shoot me a question if you get stuck on something.
@sixstringmarauder
3 жыл бұрын
Loving all the tips and knowledge you have given us, many thanks brother.
@MagnetOnlyMotors
Жыл бұрын
That was fantastic info, Joe .
@samterian7694
3 жыл бұрын
its amazing how much machining knowledge you have and the best part is you are generous in sharing with us, thanks a lot
@joepie221
3 жыл бұрын
It's my pleasure
@JPGuay
8 жыл бұрын
You are a great instructor ! Tks
@joepie221
8 жыл бұрын
Thank you
@marshallbrooks9897
6 жыл бұрын
The more I look at your videos the more I fine I didn't know great job thanks
@joepie221
6 жыл бұрын
I had a friend that always said " Its impossible to know what we don't know". It took a while to figure out what he meant, but its so true.
@oddjobbobb
4 жыл бұрын
Very informative. Clear instruction as always. Thank you.
@jeremyarnold1979
2 жыл бұрын
Awesome video sr, thanks for everything you do for us.
@robortkristensen3818
7 жыл бұрын
Thanks a lot. Never even knew about those adjustment screws. Now lets check my old lathe.
@joepie221
7 жыл бұрын
Lets hope you have them.
@michaelphillips655
7 жыл бұрын
Just bought a lathe thank you for taking the time to teach
@joepie221
7 жыл бұрын
Good luck.
@dinosspiliopoulos760
4 жыл бұрын
Mr Joe big thank you for all your videos.
@tylerjones3894
7 жыл бұрын
Alcohol wipes/hand sanitizer and (surprisingly) dry erase markers will remove sharpie/permenant markers from dry erase boards. We used to do this on OPs boards while I was deployed, so we could keep somethings (columns and rows) permanently attached to the board and variably information (operations, locations, etc.) removable ... Just in case you hadn't already had this mentioned.
@bigt1ful
7 жыл бұрын
thank you ----- we need someone like one joe i have a machining for 42 yr
@forest-bass
7 жыл бұрын
great, simple, widely-missed point. keep them coming!
@gregdunne1192
5 жыл бұрын
Great tip ,thanks Joe. I always learn things from your video and explanation that help me do a better job.
@joepie221
5 жыл бұрын
Mission accomplished.
@PisTTasha
8 жыл бұрын
Big thumbs up form north Africa . please keep em coming
@joepie221
8 жыл бұрын
Wow. Thanks for checking in. Its good to know how far these videos reach out. Stay tuned, more to come.
@bfflorida2311
5 жыл бұрын
👏👏👏 Bravo... Simple... Correct... Master of the trade.. all in one..👍
@mikesadventuresnz
8 жыл бұрын
Great Joe. Really made sense and appreciate your time helping us. Your tips even work down here upside down in New Zealand. Cheers Mike
@NordicDan
4 жыл бұрын
Getting a lot of good ideas to true up ( to the best of its capabilities) my old Craftsman 109 benchtop lathe so I can refurbish old DC motors. This and your video for truing up a non adjustable chuck have given me a great place to start for ensuring the rotor assemblies from these motors I'm working with are straight and true. Just need to invest in a better dial indicator than the Harbor Freight I've had for almost 25 years, HA!
@joepie221
4 жыл бұрын
Brown and Sharp or mitutoyo
@terapode
7 жыл бұрын
Fantastic. Best hint ever!
@joepie221
7 жыл бұрын
Very important first step. Always.
@armdaMan
7 жыл бұрын
Hi Cap'n Thanks again for sharing and informing us. This explains tons and will definitely assist in proper accurate turning. We never stop learning every day. Cheers aRM
@joepie221
7 жыл бұрын
Good to hear from you guys. Hows the knife project going?
@allengentz7572
8 жыл бұрын
Thanks Joe, I have picked up on the temporary collet video. Thank you again for the information so clearly presented. Please accept a big AUSSIE Onya Mate.
@joepie221
8 жыл бұрын
Glad to hear it Allen. Good luck to you. and.....I gladly accept the AUSSIE greeting.
@schickstead
7 жыл бұрын
Thank you for this video. I am currently working as a cnc lathe operator, and I love to learn new techniques that I can apply to my work.
@joepie221
7 жыл бұрын
This is a good one !
@mathieusteffelaar7219
7 жыл бұрын
Very good information, very useful. I will see what I can do on my Sheldon Lathe of 1952. Greetings and keep going.
@montemontemagni1658
8 жыл бұрын
Brilliant!! It's one thing to buy the tool, quite another to know how to use it! Thank you
@joepie221
8 жыл бұрын
Its the most important tool in your box.
@jeeprenegade1985
5 жыл бұрын
Good video Joe, well explained.
@joepie221
5 жыл бұрын
Its often overlooked, but very important. Thanks for watching.
@WCGwkf
6 жыл бұрын
At work for cnc grinding we have 6 jaw chucks with the 4 adjustment set screws and we call it tapping and bucking ( for buck chucks). If you're indicating on 2 diameters we tap out front away from the chuck and buck it close to the jaws. If there's a face for the datum we indicate the face and buck the OD in. Everything falls into a tenth and works quite well. When you don't have but a couple thou atock removal you don't have room for parts to be wobbling around! Also, when were tapping the part in, we run the chuck at 100rpm ( or personal pref.) And it makes tapping it in very fast. Great video.
@joepie221
6 жыл бұрын
Sounds like you have a good process there. Thanks for the comment.
@russellanderson8954
7 жыл бұрын
Joe, I am hard of hearing but your voice is great on your videos., Thanks Russ Anderson.
@stratocaster1greg
4 жыл бұрын
Thanks for sharing your knowledge. Im always learning and videos like yours are a valuable asset.
@larry527az3
8 жыл бұрын
Hi Joe, I'm a recent subscriber to your channel and I'm learning a lot watching your vids and wanted to say thanks! Great stuff here.
@joepie221
8 жыл бұрын
Thanks for signing on.
@brianjohnson217
5 жыл бұрын
Hi Joe , just watched another very interesting video of yours regarding precision indication on the lathe. You've just reinforced my findings on this subject ( I'm a mechanical engineer ) but self taught machinist. You have my absolute respect regarding all your tutorial videos and anyone who dares to give you a thumbs down does not appreciate what an accomplished engineer you are . Christmas day here in the UK merry Christmas Joe . Brian
Пікірлер: 762