What happened to you guys? This videos are so helpful
@mrbriancandoanything709
2 жыл бұрын
Take out the front drain plug and replace with a regular plug and you can tighten it down below flush for maximum clearance.
@hobonickel840
2 жыл бұрын
Thanks..I had a question..you did all the stage one mods, gov delete, did you change valve springs? Can I do stage 1 and change springs to #18 without swapping flywheel ...why do I keep hearing that you need to go to bullet fw on these hemi's?? Thanks
@CJDEM
4 жыл бұрын
Just found your channel, I’m buying mini bikes for my boys this Christmas and you guys are awesome. By far the clearest information on the upgrades. Thanks and keep it up!
@LetsBuildThat
3 жыл бұрын
Thank you Doug.
@jeff2.088
Жыл бұрын
can you share the list of parts you used?
@JacksonRuby
2 жыл бұрын
Hey just wondering what cluch are you guys using
@chriscollison933
3 жыл бұрын
All the 212 I’ve ever delt with I’ve never done a clutch backwards? How did that work out? I’m curious cause it’s good thinking honestly!
@LetsBuildThat
3 жыл бұрын
Works great.
@hondalifestyle780
3 жыл бұрын
Hell yea im in the process of installing a 212cc on my mini bike that came with a battery and I couldn’t find any videos on how to do it and this are going to be perfect thanks guys
@LetsBuildThat
3 жыл бұрын
Awesome... have fun with it!
@mrbriancandoanything709
2 жыл бұрын
What’s a bad boy?
@uppairkk1811
3 жыл бұрын
Do you have to buy individual clutch when you buy these Predator 212
@LetsBuildThat
3 жыл бұрын
Yes, you have to buy the clutch separately. The Predator 212 does not come with a clutch.
@higbieartroom8011
2 жыл бұрын
Hi! Can you share a list of all the parts that you used in the build and where you purchased them from? Thanks in advance!
@williechestnut7133
3 жыл бұрын
Very well executed
@LetsBuildThat
3 жыл бұрын
Thank you.
@alonzofisher1022
3 жыл бұрын
Why my rear wheel doesn’t roll its very very hard for the rear wheel to roll
@LetsBuildThat
3 жыл бұрын
Chain may be too tight.
@randymanuel8932
4 жыл бұрын
What exhaust header is that? I'm doing the same thing and want something like that
@LetsBuildThat
3 жыл бұрын
Purchased the exhaust off Amazon.
@patrickcarney3110
2 жыл бұрын
@@LetsBuildThat Mind sharing a link to it?
@lil_krapiton
3 жыл бұрын
Why did you use 3/4 inch spacers in the back and 1/2 inch in the front?
@runit5772
3 жыл бұрын
Remove front drain plug & apply lock tite.. snug it back in & use a cut off wheel to cut the head of the bolt off. You can almost make it flush to the engine. Gives you enough room to wiggle/mount the engine flush onto the mounting plate. To change the oil use rear drain plug. You will need to shave the plastic housing a little behind the choke & fuel levers.. line it all up with clutch & sprocket.. 👍🏼 Built close to 20 of these monster moto/motovox.. Also grade #5 bolts.. a must!! Nice video by the way..
@JTDontForgetMyMoney
6 ай бұрын
man i have watched these videos and i am just trying to figure out if it 𝘤𝘢𝘯 𝘣𝘦 𝘥𝘰𝘯𝘦 with the origianl chain and clutch?
@LetsBuildThat
6 ай бұрын
No, it cannot be done with the original chain and original clutch. The output shaft on the 212 engine is larger than the output shaft on the stock engine; therefore the original clutch will not fit and cannot be adapted. The original chain is too short and must be lengthened to accommodate the new components. I suppose it may be possible to reuse your original chain and add a few links from another chain (be careful to match sizes) and add an additional master link (that's code for "add an additional failure point").
@MSCSphoto
4 жыл бұрын
If you made the rear spacer 1" maybe the exhaust would clear the fender?
@robhazelet5657
4 жыл бұрын
Awesome video! The 212 doesnt seem to fit with the spacers and the factory muffler. Thinking about cutting off the front oil plug to slide the motor all the way up still and it should work with the factory muffler and no spacers. Any other way to do it without cutting the frame?? I do not want to put an aftermarket pipe on it.
@robhazelet5657
4 жыл бұрын
Answer: yes you can. I cut off the oil plug head on the front. Also had to notch out the heat shield on the muffler to fit around the frame. Did not have to modify stock air box.
@darrellmusselwhite6948
2 жыл бұрын
What exhaust pipe did you use on the build? Thanks I used your video to build mine 😂
@jsherman999
4 жыл бұрын
Great videos, very detailed. If you install the 212 stock without the stage one kit, do you still need the spacers? Thanks
@LetsBuildThat
3 жыл бұрын
No need for spacers
@tk429
3 жыл бұрын
When talking grade 8 vs grade 5. What about stainless bolts? They usually come in about as strong as grade 8.
@travisedwards8538
3 жыл бұрын
Where do you install the extra spring for the throttle linkage
@CCBZRG
4 жыл бұрын
I have a HRM billet aluminum adjustable motor plate, do you have any recommendations for how to properly mount it and where to drill holes on a MM 105 frame?
@MSCSphoto
4 жыл бұрын
HRM billet aluminum adjustable motor plate? Link please?
@rashidward1369
3 жыл бұрын
Hey guys can I use the same chain from the moto80 once I put the predator 212on?
@spencerheiner5056
4 жыл бұрын
also noticed the bolt that holds in the clutch is not the same as the one removed from the 80cc. Do you know the bolt size the predator 212 uses?
@LetsBuildThat
4 жыл бұрын
5/16x24 (fine pitch).
@rodmaples8196
3 жыл бұрын
I used a piece of marine plywood instead of the metal spacers to raise the engine so I could add a torque converter instead of the cent clutch. I also mounted the fuel tank in front of the seat on top so it's easier to access the fuel cap. With the torque converter the bike will raise the front wheel if you open the throttle too quickly. The plywood seems to decrease vibration.
@vividcarson5916
3 жыл бұрын
good job guys
@LetsBuildThat
3 жыл бұрын
That's quite a swing - You like the video, then you want to cancel us with BLM by inviting them to our page, then you talk about my sibling's anal sphincter. Bro, we are glad to entertain you, but these comments are nearly impossible to follow. Maybe edit them up for clarity.
@ChrisBusy
3 жыл бұрын
good stuff guys... what's the best way to maintain easy starting when taking the Predator 212 to a stage one level?
@dabosssr24
Жыл бұрын
Should start easy after stage 1 if everything is assembled and installed correctly
@charlesromstadt5308
4 жыл бұрын
Your final install video won’t play, need to know how you mount the motor
@LetsBuildThat
4 жыл бұрын
plays fine on my end.
@ricardomorin4260
3 жыл бұрын
What kind of header pipe is that
@MetrosFinest
4 жыл бұрын
What size spacers did u have to use for the lift of the motor??
@MSCSphoto
4 жыл бұрын
He said it was 1/2 inch front and 3/4 inch at rear.
@eddiecarino4587
3 жыл бұрын
Was that a 3/4 clutch? Better yet what size?
@therealdjbamnyc2391
4 жыл бұрын
so you use the same clutch from the mm80? n yea great step by step video
@LetsBuildThat
4 жыл бұрын
BAM NYC , no the MM80 uses a smaller clutch, a 5/8 id. You will want a 3/4” id clutch to match the crankshaft of the Predator 212.
@therealdjbamnyc2391
4 жыл бұрын
@@LetsBuildThat any suggestions or other specs I might need to know other than 3/4 clutch
@LetsBuildThat
4 жыл бұрын
@@therealdjbamnyc2391 , Make sure your clutch matches the crankshaft of the engine you choose. The HF 212 Predator is 3/4". The centrifugal clutches work with a spring that compresses the shoes inward. These shoes are thrown outward by the rotation of the engine, and when the engine is spinning fast enough the shoes overcome the force of the spring and push outward on the clutch bell. A lot of stop and go riding will heat the shoes and bell. You will have an issue if you get the spring too hot as it won't pull the shoes back in so your clutch will be "engaged" any time the engine spins. Choose a clutch fits your budget and desire - you can spend 20 dollars all the way up to a few hundred dollars. I like the 20 dollar ones, they work well and if you tear one up they are cheap (enough) to replace.
@taddmeyer7697
3 жыл бұрын
what clutch did you use? I'm doing this exact swap!
@LetsBuildThat
3 жыл бұрын
You need a 12 tooth 3/4 inch bore clutch. The clutch from the 80cc motor won't work.
@nicholasgonzalez4125
3 жыл бұрын
35 chain?
@LetsBuildThat
3 жыл бұрын
@@nicholasgonzalez4125 Yes sir.
@TheRomeNi99a
3 жыл бұрын
Hey guys i bought one of these designs from someone and fell on the bike 😅. Not to hard but long story short, the engine now has trouble starting up and when it does, it either dies after idling for a few seconds or dies immediately after pressing the gas. Spark plugs have been changed
@beentheplayersway
2 жыл бұрын
Has is ever set outside in 🌧️ in rain?
@beentheplayersway
2 жыл бұрын
What type of engine is it the original or a swap
@TheRomeNi99a
2 жыл бұрын
Thanks for the reply! It just needed gas 😵💫
@spencerheiner5056
4 жыл бұрын
Good video guys
@earlblumpkins9111
3 жыл бұрын
Can you use the chain from the 80cc motor on the new 212 clutch. Tryna get a parts list for all i need. Im not gonna go stage 1. Gonna keep.it simple.
@LetsBuildThat
3 жыл бұрын
You need a new chain.
@ronalddennis333
3 жыл бұрын
Can we get a part list
@wilde.coyote6618
3 жыл бұрын
These guys are great. They pound iron, and work modifying mini bikes. Good work fellas.
@Nouri_TV
3 жыл бұрын
Sweet duo man.. Liked the vid & subbed
@nwader
3 жыл бұрын
Very very good video....I'm going to save this one and follow you guys exactly. It's videos like this that gives me confidence in doing jobs I wouldn't otherwise attempt. Keep up the great work.
Пікірлер: 74