This is the first time I heard someone talk about the residue that is left in the open area of the stencil...I really needed that tip at the end..thanks.
@tainoink
3 жыл бұрын
Your welcome 🙏
@maybeimar0b0t
Жыл бұрын
This is by far the best tutorial I've been able to find on KZitem. Thank you 😊
@jimkozikis892
3 жыл бұрын
Thank you for sharing your experience. Folks like you help the folks starting out.
@tainoink
3 жыл бұрын
I love to support our community
@sgtteabags1537
3 жыл бұрын
I used to have issues with the water streaks pouring into the design, I realized that the mistake was in drying the screens on their sides. I made the adjustment and started drying the screens flat on the ground, what I do is, I use 4 small containers, and I put the screen on them raising the screen above ground and I put the fan next to them. The excess water pours down off the screen instead of streaking down like it would when dried on their sides. Hope this helps.
@kristmadsen
Жыл бұрын
It's likely the screen wasn't fully cured, or under exposed. That residue he is talking about is emulsion that ran into the stencil. After drying the screen hold it up to a light and move it around , if you see some shiny (greasy?) looking spots in your stencil than you need to wash those out somehow .
@winstonriebeek1972
3 жыл бұрын
A lot of information in fourteen minutes. Keep it up John. 👍🏿👌🏿
@tainoink
3 жыл бұрын
Thanks, will do!
@lindsey540
Жыл бұрын
Best video I’ve seen this far! Looking for the little details that matter for better prints & avoiding those annoying pitfalls. Thank you. You now have a new subscriber 😊
@locallegendprinting
2 жыл бұрын
Thank you for ur vids. Helps so much.
@phototec
3 жыл бұрын
You the man, love your videos....Thank God for you!
@tainoink
3 жыл бұрын
I appreciate that!
@sounderson672
3 жыл бұрын
Thanks, man, you make the tedious part of the screen printing simple/fun. Great video.
@whitetiger8743
3 жыл бұрын
You're da reason I've taken up screen printing.. Watup from Australia.. Can we clean out the image and reuse the inkjet transparency sheet? And it would great if you could show us beginners how you mark your plates. Always love your work.. God bless❤️
@99SBX
Жыл бұрын
Your channel is awesome! Very informative. Thank you!
@keveromzito6849
3 жыл бұрын
Am new to screen printing Thanks to your videos have learnt. Paul from kenya
@angeladixon6005
3 жыл бұрын
I'm new to screen printing. Great video.
@tainoink
3 жыл бұрын
Welcome aboard! Thanks for watching.
@AshleighP91
3 жыл бұрын
Love your content bro!! its very helpful! I'm starting out on my own venture so watching your video's is very insightful and inspiring! Plus your communication is A1! Keep up the great work! Im sure there are many more people like myself benefiting from your knowledge! I appreciate you bro! Stay safe!
@TheInkBuildUp
3 жыл бұрын
Awesome video. I just recently bought some ink remover and Emulsion remover, a big improvement from my old diy style using gasoline and bleach. But since it was my first time, using these chemicals, I still need more practice. I definitely need some good scrubs, as well, a dehazer.
@freedomlifestyle3842
3 жыл бұрын
I buy my supplies from ECOTEX on Amazon as well. I use their LED Emulsion because it cures in 20 seconds and holds up to water based inks. A dehumidifier in your screen drying area will dry them out 100% in no time. And I mean DRY!!! Hot water clears the design out in 10 seconds. No need for the pressure washer anymore. After washing out the design, lay them flat, so that the emulsion does not run into the design. Pro tip, back to the dehumidifier to dry out faster. . . Hot water tanks are cheap and easy to install inline to your booth. Dehumidifiers are on sale. It's winter.
@tainoink
3 жыл бұрын
Thank you for the info
@TheCleaners63
Жыл бұрын
Great video my guy🏁⚡️
@tainoink
Жыл бұрын
thanks
@sal6688
2 жыл бұрын
God Bless you for these videos man
@superteeprints371
3 жыл бұрын
nice video john great tutorial good stuff
@tainoink
3 жыл бұрын
Thanks 👍
@r-familyhomestead7064
3 жыл бұрын
Great video! Thanks!!
@Binulifestyle
3 жыл бұрын
love from India ❤️🇮🇳
@tainoink
3 жыл бұрын
Thank you.
@esdaesda9997
3 жыл бұрын
Very good thank you
@natezgraphics613
3 жыл бұрын
Good tutorial clean and organized like me! Definitely got a New subscriber!
@tainoink
3 жыл бұрын
Thanks for the sub!
@PamPerryJones
3 жыл бұрын
Tanks again!
@josecarlosgarcia6477
3 жыл бұрын
love from cuba bro🇨🇺
@tainoink
3 жыл бұрын
Big up
@artladz3463
2 жыл бұрын
Where do you buy the 2 in 1 dehazer/degreaser ?
@leviteapparel
3 жыл бұрын
GOOD INFO.
@tainoink
3 жыл бұрын
Thanks!
@barsheenhokes5354
3 жыл бұрын
Thanks for sharing 👍
@tainoink
3 жыл бұрын
Thanks for watching
@justchilling7594
3 жыл бұрын
I find reclaiming and dehazing 6 screens at a time is more efficient do 6 then wash the first one again no wait time needed.
@BordadozOrtiz73
Жыл бұрын
What exposure unit are you using again? I repeat the video twice and couldn't hear it right..Sorry Thanks again
@arashkermajani5571
3 жыл бұрын
Thank you
@tainoink
3 жыл бұрын
You're welcome
@kingmakthegod3060
2 жыл бұрын
Where can I find the svp emulsion? Ryonet switched to another brand.
@chelseabehm5732
3 жыл бұрын
Where do you get your transparent film and what type of printer do you use? Thank you so much for this video. It was very informative!
@tainoink
3 жыл бұрын
You’re welcome 😊 I get my films from screenprintdirect.com and my printer is the Epson Artisan 1430 inkjet printer. They don't make this model no more but you could find them at ebay.
@kristmadsen
Жыл бұрын
I've been using canon ix6820 , it works good. Breaks after about 2 years but it's also $2000 less.
@nubreedapparel6012
2 жыл бұрын
How do you put a mesh on the frames?
@HLE829
2 жыл бұрын
What emulsion remover do you use?
@nanangefendi8619
3 жыл бұрын
What printer,do you use for printing the screen,sir and what kind of ink,,is it regular printer
@tainoink
3 жыл бұрын
Artisan 1430 from Epson. It uses regular ink.
@AshleighP91
3 жыл бұрын
Im trying to look for a printer which is good enough to print on transparent film but i dont want to break the bank if i dont have to. Is there anything specific that i need to look for in a good printer? Any advice would be great bro! Thanks
@tainoink
3 жыл бұрын
Make sure is an inkjet printer and it could print large format like 13x19 film. My advice check on Ebay. Seen a lot of good deals on inkjet printers.
@nelsoncheti4629
2 жыл бұрын
Hello. I have been trying to screen printing but whenever I start cleaning the screen, the image does not show on the screen. What might be the problem?
@tainoink
2 жыл бұрын
Check your exposure time. Plus make sure your screen didn't get any uv light.
@kristmadsen
Жыл бұрын
Might be bad emulsion
@lettysanchez716
2 жыл бұрын
So if we use the home depot light for pir burning, would that work for half tones as well?
@tainoink
2 жыл бұрын
Yes.
@kristmadsen
Жыл бұрын
Get a couple 60-80w black lights off Amazon.
@rolandonarvaezg.195
3 жыл бұрын
jefe, la esquina del marco estaba sucia.
@tengislinkinpark
3 жыл бұрын
7:54 whats the name of emulsion?
@ianbowie8121
3 жыл бұрын
Hey bud ! Another great and helpful video . Question for you , I am looking at an 8 color press but its not top top quality in fact its a Chinese brand . Its looks like its well built and I dont have a lot of money to buy a high end ! Should I go for it ? Or not waste my money ? Its the ASC365 product # 219009 . I'd love your opinion on it please :) Thankyou !
@ianbowie8121
3 жыл бұрын
Oh also this will be my first screen press lol
@tainoink
3 жыл бұрын
It's best to get yourself a good press. A lot of people get into screen printing and because they pick up a low quality press they find it hard and quit and the reason is that they didn't get a good quality press. A good quality press will make your learning much easier. Do more research on that ASC365. Thank you.
@ianbowie8121
3 жыл бұрын
@@tainoink Thankyou for your wisdom and taking time out your day to help me :)
@bzbenjii6409
3 жыл бұрын
Are you from ny
@tainoink
3 жыл бұрын
Bronx New York
@wilmerlens
3 жыл бұрын
just found your channel. How can I get in contact with you?
@tainoink
3 жыл бұрын
Thank you. You could DM me @johntaino on Instagram.
@wilmerlens
3 жыл бұрын
@@tainoink thanks bro! I messaged you.
@RobGraham048
3 жыл бұрын
knowing these things has made screen printing more fun and less tedious for sure.
@flaming6666
3 жыл бұрын
PLZ - never ever put degreaser on your fingers 5:38 or skin - cos to degrease your skin is VERY unhealthy!
@tainoink
3 жыл бұрын
Thank you. I usually put on gloves but now I know it's a must. Thanks.
@flaming6666
3 жыл бұрын
@@tainoink No prob my freind! Stay healthy! ;)
@everyoneisonsteroids2720
2 жыл бұрын
I can’t find that 2 in 1 dehazer/degreaser anywhere. Did they stop making it?
Пікірлер: 78