Not all bearing with abs have one metal side. There are ones with plastic on both sides. A small piece of metal will tell you which is the magnetic side and that will be where the abs sensor rides across
@michaelovitch
Жыл бұрын
Yes, they sell a sort of card with iron powder in a transparent sheet wich reveal the magnetic track on the bearing's side.
@MrThetaphi
4 ай бұрын
Thanks for sharing this! At 4:23 you are tackling a common problem - the inner race almost always doesn't come off. You are using a cutting wheel on your angle grinder in order to vertically split the inner race, whereby it is hard to not cut into the hub (which you did, as is visible at 9:34). Here, I have used a different technique for some 40 years, which is safer: I use a grinding wheel on my angle grinder, tangetially grinding down the inner race (parallel to the hub's axis). It will show a crack, once it is ground down to about half a milllimeter, it comes off easily and the hub is unharmed, almost no hammering needed. I hope that makes sense.
@michaelovitch
4 ай бұрын
Yes it makes sense,and thank you for the advice,i will try that We didn't damage this hub,the person before us did lol The bearings were replaced already on this car. however i damaged one once.
@ringwormts115
2 жыл бұрын
Very good video , i bought a 12 tonne press recently , well worth it
@michaelovitch
2 жыл бұрын
Thank you Yes, a press is really useful : )
@Hamid-az
7 ай бұрын
WD- 40 😂 please don't kill yourself 😂
@michaelovitch
7 ай бұрын
When i press the bearing ?
@josefranciscoesquertalaman3827
8 ай бұрын
Presente en las aventuras de mecánica automotriz cordial saludo desde NAVOJOA Sonora México 🎉
@michaelovitch
8 ай бұрын
Bonjour desde cerca Lyon en Francia : )
@markballenger513
3 жыл бұрын
Hes got those skinny press plates on edge......needed that yesterday
@michaelovitch
3 жыл бұрын
You can buy them online for relatively cheap. There are a bunch of shapes,sizes and thickness. What did you work on ?
@BILLCHRISTOY
4 жыл бұрын
Great lesson,thank you
@snells-window
5 жыл бұрын
Excellent video. I need a press. Thank you Michael
@neik1976
4 жыл бұрын
Oh you moron there's no brain in General
@jaggass
5 жыл бұрын
No sweat or tears but blood.
@michaelovitch
5 жыл бұрын
For sure,those bearing don't like to get hit.
@canuckfixit7722
4 ай бұрын
What size press did you use? 10T, 12T?
@michaelovitch
4 ай бұрын
It's a 20T but i never used it full pressure on a bearing. I bought this one because it's tall and you can slide the shaft on both sides in case you have a weird hub shape to press a bearing in.
@cjskrome3228
4 жыл бұрын
Très bonne vidéo. Jusqu'à combien de tonnes va votre presse hydraulique ?
@michaelovitch
4 жыл бұрын
Merci, 20 tonnes,mais ce n'est pas une absolue nécessité ,10 tonnes suffisent largement la plupart du temps. La place disponible pour poser les pièces à presser est souvent plus importante que la force qu'elle développe.
@cjskrome3228
4 жыл бұрын
@@michaelovitch Merci🙏🙏
@davidcornuault8081
5 жыл бұрын
Salut super la vidéo et un gros pouce 👍👍👍👍👍
@michaelovitch
5 жыл бұрын
: ) Merci !
@blackmesa27
4 жыл бұрын
je pense qu'en laissant du liquide de frein ou du degrippant agir quelques jours ça aurait été carrément plus simple 😁
@michaelovitch
4 жыл бұрын
Oui,mais on avait que quelques heures... : )
@elmoz122
2 жыл бұрын
$30 bucks saves you a lot of headache
@michaelovitch
2 жыл бұрын
I don't understand.
@canuckfixit7722
4 ай бұрын
@@michaelovitch $30 for a shop to do this for you. Well, I'm in Canada and its more like $100. Do this two times and the press pays for itself.😏
@michaelovitch
4 ай бұрын
@@canuckfixit7722 Yes,that's why i bought a press. I did a bunch of those and it paid "itself" already.
Пікірлер: 36