SUPERB EXPLANATION OF MAXING OUT THE ENGINE WITH THE UNLOADER VALVE
@sivucit
7 ай бұрын
Brian, do you recommend AR pump over AAA pump. I am buying after market washer and it has honda GX200 WITH AR pump. all dewalt one has AAA pump. Need your help pls.. yes CAT would be better, but i could find only AR
@Brian_the_repair_guy
7 ай бұрын
I prefer General, AR then Cat in that order.
@sivucit
7 ай бұрын
@@Brian_the_repair_guy thanks I see AAA is junk
@sivucit
7 ай бұрын
to remove sticking pump from engine use a bolt and on other side add a nut then simply tigthen it, ,that is how we do in automotive hub removal on siezed one..
@Brian_the_repair_guy
7 ай бұрын
That works, the casing on the pump is not very strong, I have had them push through the pump housing
@chrissaucedo4095
Жыл бұрын
Can I upgrade the pump on a Dewalt pressure washer dxpw4035 model I would like to put a bigger pump but don't know what I can use any suggestions
@Brian_the_repair_guy
Жыл бұрын
If the engine is a 13hp then you can put most commercially available pumps on this machine
@gilbertocruz-jimenez3661
2 жыл бұрын
Hello Brian, I’ve noticed a small shift between the pump and housing, kind of loose, don’t think this is normal. Can this be adjusted, how? The pump is fully functional. Thanks, Gilberto
@Brian_the_repair_guy
2 жыл бұрын
Exactly where is this shift at? I am not clear on what you are referring to.
@greggcarmichael9933
Жыл бұрын
Thank you Brian. The video is a big help. I have a pump that needs replacing and the cost of a new Comet 2527 is so high I am considering a used but different model that a previous owner says still works. Are the mounting flanges on all pumps built the same to fit exactly to the four bolt holes?
@Brian_the_repair_guy
Жыл бұрын
The engines have several mounting holes. They are universal. You may not use the exact same holes, but the flange will line up on a set and you may need different size bolts.
@peterrichardson8115
2 жыл бұрын
On a machine that’s is this old and obviously used quite heavily can I ask why you didn’t replace the key as this often gets worn due to shock loading when trigger is pulled, also I found it was best to use “Copper Slip” grease on the shaft when reassembling. Pressure Washer engineer with 20 years experience and used to build my own machines to customers specification
@Brian_the_repair_guy
2 жыл бұрын
32 years of repairing machines, average about 25 machines a week. I have never had a machine come in with the key sheared. Not going to say it does not happen, just never been an issue with washers. There is no real "shock load" on a washer. When the trigger is pulled, the pressure from the pump does increase, but it isn't causing that much stress on the key. Wouldn't hurt to replace the key and to use anti seize.
@LuisFelipe-uf3xo
Жыл бұрын
Amigo tenho um motor Honda gx340 11 HP da pra colocar uma bomba de 4000psi?
@Brian_the_repair_guy
Жыл бұрын
sim, pode ser necessário ajustar o descarregador. quando o motor funciona muito, você precisa diminuir a pressão
@braceyourselforthopedicbra8491
2 жыл бұрын
Hello Brian If I take a pic of my pump can you guide me to which packing kit and valve replacements I need for my pump?
@Brian_the_repair_guy
2 жыл бұрын
I can try.
@michaelandrade47
3 жыл бұрын
Hi Brian, i just got into pressure washing as a side gig. I have a Simpson 4400 psi machine that needs a new pump. Any idea where I can find replacements?! Thank you in advance.
@Brian_the_repair_guy
3 жыл бұрын
Sherwin William's can order pumps. If you have an issue figuring out which pump, let me know.
@achillesjoe1447
2 жыл бұрын
Hi brian.. my machine has low water pressure when we use it ..I already replaced the seal inside the pump.. I also detected that the regulator did not function as usually.. is there any percent that the regulator is the cause?
@Brian_the_repair_guy
2 жыл бұрын
Check the 6 valves to make sure there is no small debris in the valves before you replace the unloader (pressure control)
@platinumhawkpw
Жыл бұрын
Thx for this I was wondering about the set screw
@Brian_the_repair_guy
Жыл бұрын
Glad to help
@co_rust
11 ай бұрын
need tips for a broken set. Screw on a pressure washer pump act disassembled him as much as I pretty much as much as I could on it
@Brian_the_repair_guy
11 ай бұрын
I am not sure what problem you have
@co_rust
11 ай бұрын
@@Brian_the_repair_guy Don't worry, just got the pump off. I'm a very excited right now!
@every_thing_wood1251
Жыл бұрын
Do you have to drain the oil?
@Brian_the_repair_guy
Жыл бұрын
Can you be more specific with your question?
@markharris9055
3 жыл бұрын
We talked a few weeks ago and you assist me in repairing my pressure washer. It’s running again but it leaks from the bottom?? Any insite
@markharris9055
3 жыл бұрын
I can see it leaking around the ceramic plunger
@Brian_the_repair_guy
3 жыл бұрын
@@markharris9055 did you replace the packings in the machine?
@markharris9055
3 жыл бұрын
@@Brian_the_repair_guy I replaces all the packing in the head. The three that go inside and the one on the brass ring that goes inside. I also replaced the plunger. The only one is didn’t replace is the low bearing o-ring that goes on the outside of the brass ring
@Brian_the_repair_guy
3 жыл бұрын
@@markharris9055 did you use all of the seals in the kit? If not, use all the seals. If you did, then you may have damaged an O ring during installation
@markharris9055
3 жыл бұрын
@@Brian_the_repair_guy I used all that it came with. The o rings you have to buy separately and there out of stock. But he did give me the size of the ring.
@littleofthislittleofthat9088
3 жыл бұрын
Hey Brian I have a Pressure Wave rkv 3.5 g37 3600 psi it is leaking water from the bottom of the uploader. Do I need to put a new pump on it or can I replace a couple parts? No loss of pressure yet. Also how do I know if it’s a 3/4” or 1”? I don’t wanna replace the whole pump if I don’t need to but I don’t wanna tear it up trying to fix it. Thanks a lot! Debra
@Brian_the_repair_guy
3 жыл бұрын
I am not sure what is wrong with the unloader, I can't see it so I don't know what parts you would need. If the unloader is bolted on the side of the head with 2 large bolts, you can unbolt and replace with another unloader. They sell for about $80. Fairly easy to replace. I would need the model and manufacturers name from the pump itself. You can determine the shaft size by measuring the shaft after the pump is off. Most 13 and all HP are 1". 8 HP down are 3/4" 9 and 10 HP you have to measure the shaft
Пікірлер: 42