after no display I first did reset. Got diplay but missing stations. I removed and reset the black modules and it all WORKED! Thank you for excellent videos on problem solving.
@Hunter_Industries
2 ай бұрын
So glad it helped!
@simtechmanufacturing
4 жыл бұрын
Spot on video. Wish I had watched it before digging
@clarkpritts1337
2 жыл бұрын
This worked Great! I had 2 stations suddenly not show up. For once I looked at the directions first and Followed them. Ta da! Fixed! And no service call. Thank you So m7ch!
@Hunter_Industries
4 ай бұрын
You're welcome
@randyambrus7937
Жыл бұрын
i reset my 12 station controller and it still only recognizes 4 stations on run mode .but when i enter how long on each station it sees them all, but always reverts back to only seeing 1234 stations instead of all 10 stations..do i need a new controller or what
@johnsonrj74
Жыл бұрын
Exactly the issue I'm having. Hoping somebody can tell us what to do as this didn't work
@cavetownbaits
3 ай бұрын
Same
@Hunter_Industries
3 ай бұрын
Please contact our customer support department here: www.hunterindustries.com/hunter-technical-support-email-request
@hurrific
2 ай бұрын
I'm having exact same issue. How did this sort out for you?
@jjjetplane
Ай бұрын
Did you contact customer support? What was your resolution?
@stevenedwards5356
3 ай бұрын
Worked beautifully!! Thank you!!!!!
@Hunter_Industries
3 ай бұрын
Great to hear!
@Cabledeluz1977
4 жыл бұрын
Thank you! It was straight to the point!
@psir3
2 жыл бұрын
Thank you! This corrected my issues quickly!!
@Hunter_Industries
2 жыл бұрын
Glad it helped! Thank you for watching!
@JimHoy-Rockstar
4 жыл бұрын
Worked perfectly! Thank you!!
@carmenpace5649
2 жыл бұрын
My Pro-C doesn't have a power button inside the control panel nor does anything slide left or right. Do I need to just press the reset button with a pin?
@wegenerwegener
Жыл бұрын
Thank you!!! Very helpful
@Hunter_Industries
5 ай бұрын
Glad it helped
@enriquerojas829
Жыл бұрын
Wonderful, thank you!
@Hunter_Industries
Жыл бұрын
Glad you enjoyed it!
@abdullaiq8610
2 жыл бұрын
thank you so much. very helpful
@Hunter_Industries
2 жыл бұрын
Glad it helped!
@michaelhuser964
3 жыл бұрын
Thank you!
@Hunter_Industries
3 жыл бұрын
Thanks for watching!
@georgelowellohhdgg63nnd96
5 жыл бұрын
Once you reset, do you have to reprogram and set up the unit?
@betterdayz2011
5 жыл бұрын
george lowellohhdgg63nnd I’m wondering this too
@waynebutler7813
4 жыл бұрын
Easy peezy....but I still have a problem. I can reset them, check that all zones are showing, but as soon as I begin programming...I'm back to just the first four zones showing. Could it be the other two modules have gone bad?
@brandonmoore2539
3 жыл бұрын
Special video this one
@Hunter_Industries
3 жыл бұрын
Thanks for watching!
@StevenMcMullin
3 жыл бұрын
my Pro-C will not factory reset no matter what I try????? help
@Hunter_Industries
3 жыл бұрын
Please use the link below to go to our support page to make sure that you are resetting your Pro-C correctly. www.hunterindustries.com/support/pro-c-clearing-controllers-memoryresetting-controller
@genny2287
Жыл бұрын
@@Hunter_IndustriesPage not found!!!
@edward2602
3 жыл бұрын
We have a controller that is stuck on station 38... And turning dial doesn't do anything. Please advise. Do we need to reset? Will that erase all programs?
@Hunter_Industries
3 жыл бұрын
Thank you for contacting Hunter Technical Support. If you want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, you can reset the Pro-C. Resetting will erase the current program data and restart the controller. If your Pro-C controller has blue buttons use the reset below: 1. Press and hold the program button. 2. Press and release and the RESET button on the back of the front panel. 3. Wait until the display shows 12:00 am. 4. Release the button. The controller is now ready to be reprogrammed.
@VALLAMS79
4 жыл бұрын
I tried this and for a moment it detected all the stations but very quickly it reverted back to recognizing only 3 out of 9 stations. What is going on with the controller? I tried power reset and controller reset too but no luck.
@norrisward450
4 жыл бұрын
I’m having the same problem .. I even bought a new panel but it still does not see all my stations ..
@gambit750
4 жыл бұрын
@@norrisward450 on mine it recognizes all of the 7 stations but only one bar on the left while the solar sensor is active. When the solar sensor is on bypass it shows all 7 bars...
@joecontreras415
3 жыл бұрын
Everything was fine for a day after following the directions and stop again. I even replaced the panel but no help. I don't know weather I need to replace the modules or the entire unit. The system is under warranty and no help from Hunter. Hunter warranty is a hassle. They always ask to go to a dealer and dealer never going to honor the warranty if you bought it from an online retailer. I bought it from Amazon two years back from Amazon and I cannot go back to Amazon for a warranty replacement. Sent multiple emails to Hunter and no help. Hunter website is not showing any phone number to contact.
@Hunter_Industries
3 жыл бұрын
Hi Joe, Please email marketingservices@hunterindustries.com with your contact info so we may better assist you.
Пікірлер: 41