I like that top idler, gives the belt more contact patch on the blower pulley
@BruteSpeed
3 жыл бұрын
Awesome video, thanks for taking the time to make it!
@Ultrajamz
Жыл бұрын
I cant get it fully loaded by hand, it becomes too hard to do (using a ratcheting wrench) and if I keep tightening the tensioner eventually I can’t really tighten the 9/16 and it seemed cockeyed. I’m thinking my belt has lost some tension so even though I’ve cranked it quite a bit or possible a shop has slightly bent the bolt in a way I can’t see? I’m thinking I need to have a shop correct this when I decide to replace all the belts in the car.
@angelo_giachetti
2 жыл бұрын
1996 i had P600B on a 5.0 Mustang with a 12 rib tight as drum. That was a good unit.
@ProChargerSuperchargers
2 жыл бұрын
The old faithful unit from decades ago! Glad to know you enjoyed it!
@GrabberBlue5.2
3 жыл бұрын
helpful vid. any chance a CARB kit is coming for the GT350?
@joshuas.4967
2 жыл бұрын
8:37 - Yeah that's real good! Best part.
@nemesispoe8904
9 ай бұрын
I need more content like this! Thank you
@JimmyJimenez
Жыл бұрын
man, this video is so helpful. thank you
@ProChargerSuperchargers
Жыл бұрын
Glad to hear it!
@vincentdelucia8078
2 жыл бұрын
Well, this is fine and dandy, but what do you do on a application like a sn95 mustang, where there is no adjustment on the tensioner!?
@montoyeaprice9779
Жыл бұрын
Ditto...d1sc 04gt what can be done our tensioners suck
@damico678
2 жыл бұрын
What does the preload do for the supercharger and is the tighter the belt the better?
@philliptomlinson3877
2 жыл бұрын
Can you explain how to do this on P1x CARB kit on a 2018 mustang GT? The bracket is a totally different configuration from a tuner kit.
@southsidetv1731
2 жыл бұрын
I have your original tensioner on my F1A setup on my 93 LT1 Camaro, can I switch to your new tensioner
@andy2much4u2handle
Жыл бұрын
What about the D1sc Procharger what's the best way to do that manual tensioner to get as much belt life as possible. My belt I just took off when I pulled the motor out of my car basically had no ribs barely left on the belt itself. Thanks!
@AtticAZ
3 жыл бұрын
So let me get this straight, Eric. After you set the tensioner and lock down the 3/4” (19mm) bolt and 14mm, you are supposed to back off the 13mm a bit!? I never heard this.
@ProChargerSuperchargers
3 жыл бұрын
Correct. The top nut shouldn't really have any tension on it. Since at that point it's not doing anything. Otherwise, if the tensioner loosens up for some reason, it could bend that threaded shaft.
@slyr1
3 жыл бұрын
Is Procharger going to make a heritage blower that is louder like an F1A-94
@rawlow1000
2 жыл бұрын
hi can you do a video on crank support on gt350s what gonna help so crank dont snap
@ftw9338
5 ай бұрын
gates rpm belt is discontinued
@fawazhome2460
Жыл бұрын
Hi sir, I have a corvette c7 with the LT1 416 stroker engine and I installed the F1A94 procharger with 4.13 head unit pulley and I’m planning to replace the head pulley to 3.85 with pump gas and I couldn’t find a clear lead for the size of the belt that will fits perfectly in my corvette. In addition, my current belt is K080450 could you please advise me what is the best belt number to be fit in my new upgrade? Or I don’t have to change the belt just tight it with the procharger tensioner?
@rustinpenner5661
3 жыл бұрын
Do u use the factory air box with most of these kits?
@lilboss82
2 жыл бұрын
which belt would you recommend for most manual tensioner applications?
@ProChargerSuperchargers
2 жыл бұрын
If you can run a Gates RPM that is preferred, otherwise virtually any belt will work.
@lilboss82
2 жыл бұрын
@@ProChargerSuperchargers thanks for monitoring these comments and responding!
@AtticAZ
3 жыл бұрын
How come you guys don’t do something similar to Griptec pulleys? I use a Gates RPM version belt and had it guitar string tight and was still seeing a bit of slip on a 3.70 pulley. I switched to their 3.625 pulley and all is great. I even have less tension on the same belt. 🤷🏻♂️
@ProChargerSuperchargers
3 жыл бұрын
Griptec is a patented process. It works very well, however, depending on the application we have no issues making 1000hp with standard belts and 8 rib pulleys.
@AtticAZ
3 жыл бұрын
@@ProChargerSuperchargers all good. I was just curious. 6 rib can be a pain. 👌🏼
@SrtHemiPower
2 жыл бұрын
@@ProChargerSuperchargers when are you guys coming out with new head units
Пікірлер: 33