After searching for 1.) How to wire a little relay like this. 2.) How to program one. I have to say this is the best video out there! A lot of them go on and on with various circuit board/technical terms. But this tutorial shows how mpjaonline had it wired up, (thats the main thing that helped me past my hurdle!). This video saved my Halloween Prop! Much thanks!
@beknowwhy
2 жыл бұрын
Thank you for making this tutorial so simple and understandable.
@jd70HJ19
2 жыл бұрын
Bought two on sale , no instructions in the box. After attempting to decipher the vendor`s online nstructions for 5 minutes , not well translated from whatever language they were orginally written I might add.I searched for a video hoping to find one coherent and intelligible, I found this video ... I wish I had found the MPJA webstite from the start ..it will be my go to from now on . THANK YOU FOR MAKING THIS TUTORIAL VIDEO , CONCISE EASY TO FOLLOW AND UNDERSTAND , superb job .
@rajivbasak5167
Жыл бұрын
Hello Sir, Thanks for making me understand the connection, means a lot to me, and just because of your demonstration of the connection of this module I am able to complete one of my personal projects, Thanks a lot, god bless you.
@HyoosikLLC
3 ай бұрын
Could not have done i without your video! Thank you.
@maximpulse
Жыл бұрын
You are wonderful! I truly appreciate your complete explanation and also showing how you wired the darned thing!!! Thank you so much!!!
@viper8049
3 жыл бұрын
Thanks, bought a couple of these from amazon and of course, not one letter of instructions. You made it easy!
@windowpane1000
Жыл бұрын
Thanks for this tutorial! It was very clear and it helped me understand how to use this relay. The written instructions that come with the board are super unclear, so this video was quite helpful.
@myturkishlife1777
Жыл бұрын
This is perfect , 3.2 is the program I was looking for 👍😁
@mr.awesome8748
9 ай бұрын
I gotta say, your a life saver😎😎 I have one of these and boy lemme tell you its confusing; however you make it simple and relatable!
@praradable
7 ай бұрын
From Holland thank you for the tutorial! very easy to understand, very clear video! Thanks a lot!! Greetings from The Netherland and have a nice day. Peter
@johnathanmyers7033
2 жыл бұрын
Thank you thank you thank you! I have no experience working with timer relays and as is the case with most small electrical components you can order online the instructions are poorly translated or there are none at all. The available instructions for this particular timer are notoriously challenging to understand and I gave up trying to figure out how to use it months ago. Now after watching your tutorial I can finally use it.
@wangofree
4 жыл бұрын
Excellent. These module type instructions are sometimes hard to follow. Thanks for working through the different programs.
@ducter2001
5 жыл бұрын
LIFESAVER --- Thanks for posting this...
@AJ-Palermo
2 жыл бұрын
thank you! very helpful video. I will definitely be buying some of these from MPJA.
@smknewman
2 жыл бұрын
There is one more function: Hold down up or down button (F1 is normal operation, F2 when powered up relay turns on with no countdown time) Stop button turn on and off.
@James_Bowie
4 ай бұрын
Only on the XJ-801 version
@themarblewurks9492
2 жыл бұрын
Great video! Very well done. Easy to understand. Saved me loads of time. Thanks!
@kelekilla
9 ай бұрын
I was just thinking to smash this item till ifound you!!!😂😂❤❤
@JMSMish
4 жыл бұрын
very well explained, it has been very useful, thanks
@0012dominic
2 жыл бұрын
Thank you so much for this. It's a better unit than I thought I bought thanks to you.
@jasonlaureles9353
5 жыл бұрын
thank you sir, it really helps me to understand the function of this.
@terrains-en-pente527
3 жыл бұрын
1fjdi
@razvanbac6239
Жыл бұрын
You are a life saver. thank you for this outstanding tutorial
@crisdt88
Жыл бұрын
Thanks for the video, best explaining video of this module I've seen so far
@airsoftjunkie5592
5 жыл бұрын
Thank you very much for this awesome video. Just received this in the mail, but had no idea how to program it with no instructions. If you ever do another one, it'd be very helpful to hook something up to the NC or NO side, to demonstrate the on/off function, like a light or fan or something.
@shavkat84
7 ай бұрын
Finally, somebody explained nicely thank you 🙏
@harishmadhu5444
4 жыл бұрын
This explanation was easy to understand. Thank you very much.
@ronaldhietbrink7800
3 жыл бұрын
Dank wel prima uitleg ik heb de stappen gevolgd en heb de schakelingen prima voor elkaar gekregen
@bogoff99
5 ай бұрын
really appreciate this video.. the broken translated instructions that came with it was terrible..🤣 I sussed some features out by playing around but your video helps so much. 👍
@plasticelectrics
3 жыл бұрын
i want to like this upload twice.... just perfect thankyou
@mpjaonline
5 жыл бұрын
Depends on your sensor if it has an adjustable set point (on-off) and a transistor output to act like the switch I used. Plus a separate power source for the delay timer 6-30Vdc. Thank You
@davidosterberg1643
Жыл бұрын
Excellent tutorial. THANK YOU!
@ben200b
5 жыл бұрын
A very handy little timer !...thanks for sharing
@shabirjunior5603
5 жыл бұрын
Thanks dude, that's really helping me
@waynebagnall3611
6 ай бұрын
Very helpful and easy to understand. 👍
@toto6toto
3 жыл бұрын
Thank you sir for all the complete and good information! Godbless you always!
@rajainayat
Жыл бұрын
Wow thanks alot for such nicely explained loved it.
@gaets04
4 жыл бұрын
Finally someone explain it probably. Thank you for that educative lesson. How do you rest the whole thing ?
@mpjaonline
4 жыл бұрын
Sorry I’m not aware of any factory reset program.
@red_zone_art
4 жыл бұрын
@@mpjaonline is it posible to work whit coinaceptors
@walthodgson5780
3 жыл бұрын
You do have to have an external trigger voltage. Simply using a switch doesn't work. When using USB power there's a 3.2vdc across the power terminals but it's not enough to use as trigger voltage. As such I think USB power is only really useful if you are using P3-1 or 3-2.
@ExtremeDIYGuy
4 жыл бұрын
Awesome, thanks! All of the instructions I have seen to date on these are so poorly written as to be unintelligable! THanks for the video, makes using one of these a breeze!
@bertodiy
10 ай бұрын
clear and excellent tutorial! thank you sir 😍
@KashifJarwar
3 жыл бұрын
Thank You so much for detailed Explanation. 👍
@TheOneJacinto
2 ай бұрын
Thanks for sharing this!!, was very helpfull!!
@Hotshotter3000
3 жыл бұрын
This is really good. But I got some questions. Can you use a 9 volt battery or other batteries to power it? Do you have any videos on the wiring? I am mildly confused with the ground cable. Does it need it? I want to make sure I wire it with the trigger and the battery and everything. I'm kinda new to electronics and I just built very simple things.
@SuperRealityKid
Жыл бұрын
Great demonstration, thanks. I'm using one for an alarm system where I use a trip wire attached to a pull pin that operates a micro switch to send a 12 volt signal to trigger the board and sending an operating voltage to sirens, lights and GSM dialer. Now, here's the thing, It works most times but occasionally does not and I have a theory that the time length of the signal, on occasions, may not be long enough. A trip event pulls the pin out super quick and, once pulled, the micro switch instantly returns to its normally open state. I suspect that if the micro switch closed circuit condition is only in the order of milliseconds, it may not satisfy the boards signal parameters. What do you think? Ps. I have just modified the micro switch assembly to remain closed circuit after activating, until reset, so I am testing a few more times to check my theory out.
@LM-fq3ot
4 жыл бұрын
Thank you very much for your explanations. 🙂👍
@Nando_
9 ай бұрын
nice! I have an old car (brasilian pickup Chevrolet Montana, same as Opel Corsa C) and setting ignition on position 1 doesn't turn the ACC on (it turns on only when holding the key pressed in) for now the ACC IN signal for my Android headunit is coming from the ignition 2 position, so it only works when my dash is on, whith all the engine systems, with engine running or not I belive I can use this module setted on program 4 to allow my headunit to keep working for 30 minutes after I turn ignition off also I can cut power for the module when locking the car thanks for your video!
@TijnVos
4 жыл бұрын
Thanks man, helped me with all I wanted it to do.
@Helix751
2 жыл бұрын
Great tutorial. Thanks! The instructions in the chinese pages for this device are all but unintelligible and were driving me crazy.
@bryan_nfs5593
Жыл бұрын
Concise and detailed!
@strawman9410
2 жыл бұрын
Thanks for your efforts and sharing 👍🇬🇧 I was hoping to see this switch polarity also, with option to set voltage and amperage. If you know of a device please let me know
@fly4fun24
3 жыл бұрын
You made easy for me...thanks a 10000000 times maybe 10000000000 times
@andreashexe8645
Жыл бұрын
nice for a thunder simulation with sound and lights
@hasanahatk
2 жыл бұрын
Thank you very much sir for you info... I am get confused coz i purchased another thing but comes this one.
@astralcomm7925
2 жыл бұрын
the mosfet on that module is really hot. really need to put a heatsink to dissipate heat
@Self.reliant
7 ай бұрын
How many amps can pass through it?
@rezamahmoodifaghihi4669
24 күн бұрын
10 max
@Srt8Jeep
Жыл бұрын
P4 baby! Thanks what I’m talkin about!
@gouthamkumar1750
2 ай бұрын
In program 3.2 if you set lop to --- it loops infinitly 😊😊
@geoffreydownes7591
8 ай бұрын
Great simple video in real language - can you tell me why my unit counts up from zero rather than down from presets.
@bienvenidogranali6611
4 ай бұрын
Great tutorial!
@thisisyourtransmission
4 жыл бұрын
can this be hooked up with a motion sensor and a nine volt battery supply?
@mpjaonline
4 жыл бұрын
Yes it will work with a 9V battery but depending on the current draw of the PIR and how often it is triggered the battery would last less then a day.
@thisisyourtransmission
4 жыл бұрын
@@mpjaonline alright, what does PIR mean?
@mpjaonline
4 жыл бұрын
@@thisisyourtransmission Passive infrared
@exgenica
4 жыл бұрын
The "standby" current requirement is 20mA, and the "Relay Energized" requirement is 60mA per the datasheet on mpjaonline's website. So a typical "9Volt" battery wouldn't last long. Even a high-capacity brand new fully charged lithium-ion "9V" form-factor battery only has about 800mAh capacity. So if the board was in "standby" ALL the time, the lithium battery would last about 800mAh/20mA=40 hours...less than 2 days. (note: a lithium "9V" battery is actually a maximum of 8.4Volts and can be used down to about 6.0V)
@thisisyourtransmission
4 жыл бұрын
@@exgenica thank you
@vicomedia1
4 жыл бұрын
My unit only counts up -not down-is there an undocumented setting? I have looked all over!
@MrResidentRob
3 жыл бұрын
mine is the same but seems no answer @mpjaonline please advise us. Timer going up means power removed to activate relay which is ok for me as I'm using a standard pir which is a normally closed circuit to activate my stair lighting but if I use pressure mats they are normally open signals which will not work for this. Other than that this is a great module for various projects
@jeflehardi91
3 жыл бұрын
Thank you so much ! especially for connections
@christopherowens2635
Жыл бұрын
thanks for the video. i need this for my project
@robertmccully2792
3 жыл бұрын
Some day in the far future they might start issuing directions with these type of devices.
@FrankBuisRoyalPressAmsterdam
Жыл бұрын
Very useful, thank
@TylerHarney
4 жыл бұрын
Awesome Thank you so much! I'll be using this to trigger my laser cutter fan acc's to turn off X seconds after the program finishes.
@techinfotahir7912
4 жыл бұрын
Wow very nice information 👍
@kishoresoni4055
4 жыл бұрын
Sir you had not shown us how you connected Dc power cable to the circuit clearly. How trigger is connected to which terminals.please do so.
@rustipaul7427
4 жыл бұрын
I have problems with this board regarding debouncing of the pushbutton. Did you debouced the switch? I'm using a wall push button to start a fan in mode 1.3 and I have double triggering sometimes.
@user-vn7un4uu6g
5 ай бұрын
Handy video. Thanks.
@Electronzap
9 ай бұрын
Good info.
@mschaffer2826
3 күн бұрын
Thank you for the video. Is there a way to have it start the relay when the switch goes from closed to open?
@dhavitprem
Ай бұрын
Thanks so much. Question: what happens if I want to display 20 minutes counting down ?(visualizing the minutes)
@navi61kaivank64
3 жыл бұрын
Thanks a lot. This was very helpfull for me. :)
@mazatrolmultiplex1113
5 жыл бұрын
very good demonstration. Thanks
@IMT-AIJ
8 ай бұрын
I have a question, when using the P31, infinite loop with time on and time off, is there any posibility to override that, one time off and leave a bit longer on and then continue the normal loop? I saw the different options but I didn't see any that does exactly that. Thanks so much for your help and your great videos!!
@mudheli9110
2 ай бұрын
Can you connect a motion sensor to this
@zachroach9672
2 жыл бұрын
Thanks for the video, helped me understand the trigger function. Can anyone recommend a 2-channel version of this? I want to power 2 circuits sequentially, then have an off cycle. Currently using 2 of these with the first's NC triggering the 2nd when the first closes, but thats a lot of wires =/
@justasupercutofus
7 күн бұрын
does it have a mode where it will cycle between NC and NO at thebsame intervals?
@brightstar7704
2 жыл бұрын
In the program 3.2 if we didn't set loop value.. the counter work directly on and off as a time set without loop or what ?..!
@javelinzamot9907
3 жыл бұрын
The problem I have with the Programmable triggered timing board 35238 MP is when trigging on and of it will stop working over time I had to replace it 3 times / using a small scooter battery 12 v / do in need to add a fuse ? . or is there one on the board,?
@muxxx100
Жыл бұрын
can we use it for switching on a device continuously with a delay . say 1-2 sec delay
@SwissFrogGuy
2 жыл бұрын
Thank you very much for this video. I am trying to use programming mode P3.2 (OFF and ON in a cycle, without trigger). However, it always starts in OFF mode. I need it to start ON, then OFF (I am using the relay with a separate timer that has a minimum period of one minute. I need the relay to limit this to, say, 10 seconds. This way, I can set the main timer to power up the relay, and the relay stays on for 10 secs, then shuts off). As it is, I get a mode flashing for a few secs on power-up, then it starts the loop in OFF. The loop works OK, but all this delay at startup is frustrating. Any way to set P3.2 to start in the ON position, no off? There are no instructions. Thanks!
@doctorcross7018
Жыл бұрын
How to create a count down timer....like I turn on the button and after like 40.seconds it turns the thing on and then the thing stays on
@dalecarselli6565
10 ай бұрын
A list of what each function did would be nice
@wickummalinda5127
4 ай бұрын
I'm on P-3.2 mode with Open 10s, close 3s and loop = 3. what my problem is, like at 10:40 it does not energize the relay, and it waits until end of P-3.2 blink to energize the relay. there's about 2 sec delay. how can i program this to overcome the issue ?
@thediscoman2001
2 жыл бұрын
how do you make is do the oposite i want the relay to come on after a set period of time not just come on say for instance i want it to come on after 60seconds
@tanyathorvilson
6 ай бұрын
How fast can this timer cycle? I have a hopper feeder im working on. I want to hit the button and have it send 3 rapid fire pulses and then stop. I would also like it to continuously send pulses if the button is held down. Is this possible?
@thefaisal13
4 жыл бұрын
Many thanks, it's really helpful.
@shankarpatil8565
4 жыл бұрын
Megha Shankar Patil
@advocatusdiaboli1436
5 жыл бұрын
Thumbs up.Great video.
@GabrielSilverman
10 ай бұрын
Hello! I have this unit and your video has been extremely helpful however I'm finding that program P2 delays the relay as expected and then turns it on (LED lights up) HOWEVER if you press the trigger while the relay is on, the program starts over. In your example, the trigger starts the program but then is ignored if it is triggered again while the relay is open? I also found that my counter is counting UP, not DOWN like yours. Thoughts?
@polcrendszer
2 жыл бұрын
how shall I hook it up with a 12v motor to program turn on/off?
@mornaistar
Жыл бұрын
Please I need some help , Is it possible to connect a 12v turning signal on the output? if so how?
@never4u18
Жыл бұрын
Hi,i have a problem with the bord...if the bord isn't running any program it's switched off.... i want to make the board to wait for the trigger signal then run the program,any advices?
@backup1phone742
Жыл бұрын
The program code P3-2 is reseted to P1-1 automatically when power is turned off and then turn on. Please help
@dmitripogosian5084
10 ай бұрын
Amazon sells similar boards which also have low voltage trigger and one extra connection point on the left. Does anybody know, is it a different chip, or low voltage trigger achieved differently ?
@MdAfrid-lw7fi
Жыл бұрын
Please anyone answer my question 🙏 Which points are shorted by the black wire?
@SwgwmTJB
3 жыл бұрын
Thanks a lot man, helped a lot
@MOBT123
29 күн бұрын
How do I stop the program name from showing up every time I press the trigger?
@ammadejaz9458
4 жыл бұрын
Thank you sir for informative video, With this triggered timing board i want to make a project for home, can you please guide me? and sorry for bad grammar English, Actually i want to make a timer circuit with my doorbell at home when someone outside trigger the bell button of my home bell then the 50watt socket system turn on for specific time like (120 seconds etc) in 50watt socket system i will include 1 x door security camera 1 x 20w small LED/LCD monitor for Camera display 1 x Night LED light for outdoor (with lowlight sensor) if someone ring bell at night (Note: my door bell is like bird singing voice, as long it keep ringing as long the bell button is pressed) (Another thing: it will be more great for me if bell bell is repeatedly pressed by any person then there will no affect on this timer board, and the electricity of door bell should be separate if possible..
Пікірлер: 365