If these axle clamp bolts [ 3/4 in ] are bad I replace with grade 8 , 3/4 and bushings for lift implements I cut them so they and head of bolt is not sticking below.
@FourWindsFarm
4 жыл бұрын
Really enjoyed that one matey looks like you got a proper project on your hands keep at it and will soon start to take shape will look forward to seeing it progress! 👍
@hsagri69
4 жыл бұрын
Thank you. It's going to be a fare project. I think the correct term is a labour of love. Really looking forward to getting it done though
@casto-
4 жыл бұрын
There's still another 5yrs in them bearings! 10yrs in the good ones 😂😂. Least it hasn't turned out too bad for you, looking forward to seeing the rest done 😊
@hsagri69
4 жыл бұрын
I know but iv nothing better to do and so much money I need to waste some 🤣. I wish to both. Yeah not quite as bad as I thought which was a pleasant surprise
@owaina2765
4 жыл бұрын
Right ... so... as always another fantastic vid good job you had someone who know all the parts of a tractor 😂. Joking apart you could name them anything and I’d believe you. great job on the ASMR vid. now next time just a few more expletives and that poor international baler being used as a work bench come HS-Ag through a sheet over it or put blanks of wood over her👍👍👍👍👍👍👍👍👍👍👍👍👍
@hsagri69
4 жыл бұрын
🤣 father in law is helping out. Hes no ag experience but he is a mechanical legend. Yes I'm a very naughty boy for using the baler as a parts table. No excuse
@antonyfarming
4 жыл бұрын
Great video intatrac uk do good parts if you are looking for parts always best keep batteries charged mate neither know when you need it 👍
@hsagri69
4 жыл бұрын
Think I'll be ordering through intatrac and agriline. Usually do keep batteries up but obviously let it slip lately
@petergregory8402
4 жыл бұрын
Hi when I worked for a IH dealer we used to mod the axle by drilling it and fitting 3 bolts keeps the axle much tighter
@hsagri69
4 жыл бұрын
Handy tip thank you
@tractor180350
4 жыл бұрын
What no right right right or a groan or two that`s not like you lol, I think the old Ih as missed a service or two, great video on the strip down it sure is in need of a few bearings and loads of grease.
@hsagri69
4 жыл бұрын
I'll groan on next week's specially for u🤣.
@cibie01
4 жыл бұрын
Very nice start Mr M, now lets see if you can finish it faster than project Binky lol.
@hsagri69
4 жыл бұрын
Thanks cibie01. Get some money in for parts an we will be rolling.
@tomosharveyjones3416
4 жыл бұрын
Great video
@hsagri69
4 жыл бұрын
Thank you
@gerrydays1909
4 жыл бұрын
Good work 😀😀
@hsagri69
4 жыл бұрын
Really happy to get a start
@alasdairmeredith2711
4 жыл бұрын
We are doing up a David brown at the moment just need to get new parts and put it all back together but first we need a new shed so its turning out to be a very expensive restoration 🤣🤣
@hsagri69
4 жыл бұрын
What a great idea to get a new workshop. I need it to put my tractor back together. Good luck with ur Davy project
@alasdairmeredith2711
4 жыл бұрын
@@hsagri69 thanks
@liamsmith1310
4 жыл бұрын
Nice one Mike! Is she a Bradford built tractor? You can tell if she was made in Bradford as the serial number plate has been left without the full number! If you need any help be sure to message me as I know a Very nice chap who worked for IH or I can send him your way if you want 👌🏻👍🏻
@hsagri69
4 жыл бұрын
I think she is a Bradford. Might take u up on it but I di know her working life as weve grown up together
@liamsmith1310
4 жыл бұрын
@@hsagri69 no worries 👌🏻
@mcdowellbuses
4 жыл бұрын
Good vid
@hsagri69
4 жыл бұрын
Thank you
@andywilkinson3792
4 жыл бұрын
How do. How come you just didn't cut off other side off the nut to make live a lot easier. Sorry to say. I think you might have to buy new hup even if you think it's going to be ok that will go when you start using that tractor. Every one can say I'm wrong I don't mind. From Andy in Swindon
@hsagri69
4 жыл бұрын
The nuts a force of habit. Iv always done it to try and save the bolt. Welsh penny pinching 🤣. Already decided to replace the hub. It's not worth the potential headache. Sorry I never messaged back just missed it somehow. Promise I wasnt offended. Useful information is always welcome
@andywilkinson3792
4 жыл бұрын
@@hsagri69 how do not I didn't worry about u getting back to. I just thort I stuck me nose in that's all. Cos you all ways get back to me. I only said about the bolts and hup cos I was trying to save you some money that's all. Cos I done one for some one years. Thay wanted to do as cheap as possible like we all do I'm really bad for that. Try save what I can. But theses people who I did the job for i check everything thing on the hup but told them it might work but I'm not going to stand on that cos it was same as yours it lasted about 4 months then went it made a right mess . You could do it and have it as a spair cos bearings aren't much and they not handed so but I just didn't want to see you have to do it again that was all I really like to help people out like your self cos I uesd to do same sort off job and money is not all ways there. And if you're planning on doing more for your self I just didnt want to see you having to go mad then get another one. Bit like your mower. I new it wouldn't work cos I went down that road my self. So if i can help you out. I will. But it's up to the person what thay want to do. I only like to try and help them out. All best to you. I carnt remember were your based. But if u want to ask any thing just put a post on the last video you have put up cos it all ways comes up on my phone. Like I said only trying to help. You don't have to take any notice of what I say. U can tell go take a long walk. It never gets to me. Be nice to see her driving around. I need to get both my fergie.s running again.
@mf50b
4 жыл бұрын
Play? Or just an early form of axel suspension.
@hsagri69
4 жыл бұрын
I'm going to say play. I'm sure axles are supposed to be able to walk
Пікірлер: 32