Love the build! Did you have to trim the projector shroud?
@kenrod4
3 жыл бұрын
Nice video. Lights look great. They do sell a spray can trigger attachment that goes on the spray can to make it easy to spray the paint.
@superdwarf
3 жыл бұрын
The main issue was build up of paint on the tip itself. Just had to keep checking it every few sprays on some colors. Then the headlight bucket would look amazing and I’d come back an hour later and find bubbles in a corner or a random run. Once it got alittle warmer that stopped happening.
@johnthompson4132
Жыл бұрын
Love these headlights. Can’t wait to get my 2nd gen. I have to save this video so I can go back and watch it.
@hugogarcia7240
9 ай бұрын
I just built my headlights and the halos switchback work fine with halogen turn signals but when i put in the led switchback turn signals it cause hyperflash on both the halo and turnn signal even with a resistor harness off amazon just wondering what u did to have bothe halo and turn signla bulb.
@superdwarf
9 ай бұрын
I’d say the issue is the Amazon harness. I got resistors from the auto parts store and spliced them in myself. It took 2 per side & 1 on the back turn signals to get rid of all the hyper flash finally. I fought it for a week. I’d add a resistor and it was fine for a bit then started hyper flashing again. Once I got 2 registers per headlight & the 1 rear 1 tho it’s been fine for years now.
@hugogarcia7240
9 ай бұрын
Thank u ill try that appreciate the response I've been stumped on it.
@hugogarcia7240
9 ай бұрын
I think my led tails have built in resistors cause those never had hyperflash
@kellyanderson7115
Жыл бұрын
How did the clear lens come off? What did they do to seal it? I'm trying to do it on autosaver88 assemblies and they glued it with silicone, which seems like it's going to be about impossible.
@superdwarf
Жыл бұрын
I haven’t re watched this video in a while but if it doesn’t show it they were baked in the oven. 245 for about 7 minutes and I got lucky and every bit of the black silicon stuff came off with the clear lens and left the channel perfectly clean ready for re assembly. I cleaned the old stuff off the lens and they make a headlight specific butyl sealant. Either diode dynamics or morimoto have it.
@connerbenning4160
2 жыл бұрын
Where did u buy those exact projectors and that O ring light u had behind the projectors, want to make my headlights look like yours
@superdwarf
2 жыл бұрын
I purchased from circuit demon. com you can find morimoto projectors lots of places. The halos are diode dynamics which you can also find lots of places. There was a sale when I chose where to buy I’d shop around.
@connerbenning4160
2 жыл бұрын
@@superdwarf thank u so much.
@connerbenning4160
2 жыл бұрын
@@superdwarf where did u get the shroud for the projectors?
@superdwarf
2 жыл бұрын
@@connerbenning4160 should be a drop down menu to pick which one you want when you get the projectors
@adrianmoreno862
2 жыл бұрын
Where could I get the headlights so I can make some like these🔥🔥
@superdwarf
2 жыл бұрын
I got them off eBay. Here’s the link www.ebay.com/itm/311643040509?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=RGgc_m9cTWO&sssrc=2349624&ssuid=g5KS4YRrSnS&var=&widget_ver=artemis&media=COPY
@adrianmoreno862
2 жыл бұрын
@@superdwarf what that square of lights like the strips??
Пікірлер: 20