My thing about the overcurent protection is that you need a latching sercut to keep the load off.otherwhise you will just be power cycling youre load.
@tanishqbhaiji103
3 жыл бұрын
It is easy, add acapacitor to gate of the mosfet
@ArshadMehmood-kz6ez
Жыл бұрын
Yours all practical jobs done in very easy ways.thanks
@hidayathmydin4676
4 жыл бұрын
Hi Kasyan TV.. Very intresting to see Evil sprits.
@americanrebel413
4 жыл бұрын
I enjoyed this video, thank you.
@electronic7979
4 жыл бұрын
Excellent project 👍
@jp040759
4 жыл бұрын
Good idea. Simple and effective notification of bad situations. BUT it does not protect/prevent from them though. New video title needed
@ceilingfanmusic6597
4 жыл бұрын
It can like she said if you replaced the leds with say a power transistor to drive a relay. Or just a fet it self. The sercut she made for this video is just a dimo kit basicly. It shows the functions.
@jamesbrown99991
4 жыл бұрын
@@ceilingfanmusic6597 Can you show how the relay will work with UV/OC protection? If the load is responsible for either of these conditions (which will be likely), then the relay will oscillate.
@ceilingfanmusic6597
4 жыл бұрын
@@jamesbrown99991 for the under voltage an over curent like i said in my first coment in the vid you would add a latching sercut befor the relay so the load stays disconnected till the voltage rises above a triger to reset the latch just recenecting the load.
@tetraspace3000
3 жыл бұрын
Hi and thanks what's "zener diode" compatible for 5v power supply in this circuit? Please, somebody answer me
@tanishqbhaiji103
3 жыл бұрын
It’s a device which will only pass current above a certain voltage in the reverse polarity and acts like a normal diode in the other polarity. Watch some videos on KZitem to know more and any Power supply of 5v can be used instead without the zener
@jagannathkulkarni
2 жыл бұрын
Can we use all the protections or at least over voltage and under voltage protection for the same load? as i can see 4 separate outputs for the 4 mentioned protections.?
@JasonRobards2
2 жыл бұрын
Same feeling. As I understand it, this is an indicator circuit, nog a protection circuit.
@MiguelDeMarchena
4 жыл бұрын
only need one more feature ( reverse polarity ) to be perfect for a DIY lab work bench power supply
@l0k048
3 жыл бұрын
_F U L L B R I D G E R E C T I F I E R_
@jamesbrown99991
4 жыл бұрын
this doesn't protect anything, it just lights LEDs
@stephanc7192
4 жыл бұрын
Yes. This is the control circuit. Look at time 2:50 to add output switch. Regards
@ocayaro
4 жыл бұрын
ladi jada Replace the LEDs with n-channel mosfets to achieve protection
@jamesbrown99991
4 жыл бұрын
@@stephanc7192 Where do you connect the output of the output switch? If you use a relay and connect the output to the load you wish to protect, you will get oscillations when using the under-voltage or over-current sections. If you use FETs instead of relays, you will get either oscillations, or the load being partially turned on, and the FET heating up.
@raymondmichael4987
4 жыл бұрын
ladi jada, if there's a problem with oscillation; have you tried to use optocoupler (817) to full switch the mosfet. It helped in several cases where original signal weren't not enough to switch a load. Regarding the presented instructions, they are good enough to make it work. All the best Greetings from Tanzania 🇹🇿
@jamesbrown99991
4 жыл бұрын
@@srtv7925 pity it won't work due to causes I mentioned
@stephanc7192
4 жыл бұрын
I always enjoy your videos! They are very good! In this circuit, I do not understand how the op amp (IC 1.4) for the current would work. Are you connecting pin 10 to ground? How does pin 11 get to a voltage lower than ground? Kind regards
@ishigamiyu1991
4 жыл бұрын
Great work!
@daljitsingh1143
4 жыл бұрын
excellent [devil spirits]
@cartvincentpalaypayon4396
2 жыл бұрын
This circuit can cutoff the voltage enters the load or its just an indicator if has a fault?
@RapidBoss08
4 жыл бұрын
You are awesome
@daljitsingh1143
4 жыл бұрын
very best
@faridi-bin-Zouq
4 жыл бұрын
lovely
@stephanc7192
4 жыл бұрын
Current protection circuit is wrong
@daljitsingh1143
4 жыл бұрын
i like circuit
@hadireg
3 жыл бұрын
👍👍
@samtechpro
4 жыл бұрын
I like your channel from start. But i want to mention that Your explaining sequence is not interesting always.
@ovalwingnut
4 жыл бұрын
👍😎
@AnandKumar-ym9yw
4 жыл бұрын
Hey can be used as BMS
@netrapatil2169
4 жыл бұрын
I was thinking the same
@pavelbires
4 жыл бұрын
*cough cough* AvE *cough*
@saddamalradai762
4 жыл бұрын
Second
@forcovers438
4 жыл бұрын
first viewer
@blackartista
4 жыл бұрын
good for you 😎
@keithking1985
4 жыл бұрын
Ya!! Never Disappoint KAYSAN TV..
@praloyslife8676
4 жыл бұрын
I enjoyed this video, this very usefull.
@simyavn4810
4 жыл бұрын
Hello. i just discovered the channel and i like it. if I do not ask too much. you to explain the chip and how to use the TC4052BP We use the circuit above for a selection of audio recording on DVD, AUX, TUNER and MP3 PLAYer. Where is the IC 4052 with two pairs of 4-channel switches, so we can use a single IC in the stereo system. because I didn't find much explanation about it. please if possible. thanks
@tyronelectronics
4 жыл бұрын
Good day, What program are you using to design your pcb's. Thank you for sharing you ideas. I like this circuit. Just what i was looking for.
@anshuyadavsitaram7053
4 жыл бұрын
Hey kasyan tv i think to buy new battery charger so which is best transformer one or smps one please reply
@mahmoudtayel229
4 жыл бұрын
You are always up & Great😍 thank you for all helpful circuits you give💜
Пікірлер: 49