Great video thank you - What material do you have inside your filament dusters?
@mariuschirita2017
Жыл бұрын
Sponge, I purchased them from amazon.
@renk872
Жыл бұрын
@@mariuschirita2017 thanks what kind of sponge? The ones I have tries have degraded over time.
@mariuschirita2017
Жыл бұрын
@@renk872 Never changed them, I try to turn them around a few times. I just replace the whole filter when they are done.
@additivelabs
Жыл бұрын
Hi, in what intervals are you doing the maintenance routine? Monthly?
@mariuschirita2017
Жыл бұрын
Ideally monthly, but I don't really have the time to do it monthly, sometimes every 2 months. Cleaning and lubricating the rods is quite important and this can be done more often.
@partsdave8943
Жыл бұрын
What do you use for lube? Also, isn’t the cold pull better if done with the cleaning filament?
@mariuschirita2017
Жыл бұрын
I use the lubricant that comes in the box with Prusa printers. Probably any lube would do it . I did read good things about lithium lube but never tried it. The cleaning filament is not very good for cold pulls , it sticks to well on the nozzle and it breaks when you try to pull it out. I found PLA+ does the best job for me. Some people do it with nylon but I never tried it.
@partsdave8943
Жыл бұрын
@@mariuschirita2017 My Prusa original MK3 didn’t come with any Lube. Been using 3 in 1 oil
@mariuschirita2017
Жыл бұрын
@@partsdave8943 I prefer thicker grease, I think it holds for longer. Just my opinion. There are many videos on youtube about grease for 3d printers.
@bluerider0988
Жыл бұрын
Have you ever cold pulled with petg?
@mariuschirita2017
Жыл бұрын
I tried PETG but found PLA+ better. I found PLA+ works very well with the cleaning filament and always had successful cold pulls with it.
@tomhankstomhanks2579
Жыл бұрын
You have 3d printing broking or you dont need it sent it to me bro
@filamentive2733
Жыл бұрын
A very helpful and informative video! Marius, we would like to share something with you if you're open to this. What's your preferred email address?
@bernardtarver
Жыл бұрын
Pretty sure rod lubrication isn't doing anything other than pushing lubricate to the ends of the gantry.
@mariuschirita2017
Жыл бұрын
Yes, it is pushing some lube to the ends, but if you evenly spread the grease along the rod, the balls inside the bearings are definitely collecting a lot. The barrel ends diameter is higher than the rod's. That is the reason I keep spreading the grease a few times while moving the bed and the hotend. This worked very well for me. Some of my printers are almost 3 years old, printing 24/7 and they print like day 1.
@NigelTolley
Жыл бұрын
@@mariuschirita2017 certainly that bed sheet looks like new!
@mariuschirita2017
Жыл бұрын
@@NigelTolley that is the newest printer, a few months old. The older printers are on the bottom row. Old down, new up 😉
@remusraita8002
Жыл бұрын
Ce fel de spray e ăla,de unde se cumpără?
@mariuschirita2017
Жыл бұрын
Spray cu aer comprimat / Air duster
@grepos8045
2 ай бұрын
I would not reccomend direct skin contact with any kind of machinery lubricant.
Пікірлер: 23