NSC! Great to see you back in the place to be!!! You duh best! Hope you had a great vacation friend! Have a great weekend!
@NSC-Modz
4 жыл бұрын
Thank you so much, have a nice weekend too my friend ;)
@AdamAve93
3 жыл бұрын
Always a great job! Always watching your videos. I used a feeler gauge for my removal. Found one strong enough to flex just enough and be thin enough to not hurt it.
@NSC-Modz
3 жыл бұрын
Yeah, that's great too ;)
@AdamAve93
3 жыл бұрын
@@NSC-Modz oh I had a question. On my older PS3 I accidentally scratched the green paint off of the cpu. I don’t see the traces cut through but I did see them showing. Can I just put some flux and solder to make sure it’s a set connection or is it just a paper weight now?
@lee__1707
4 жыл бұрын
Hope you and you're family are safe and well, thanks for sharing this video with us all ;)
@NSC-Modz
4 жыл бұрын
You always welcome and hope you doing fine as well ;)
@مصطفىسعد-ص1و
4 жыл бұрын
Hello man im very glad to see your videos again you really change my working life i started with you from downgrading ps3 nor. Oh my!! really old good days. I have some question with many ps3 slim customers, How can i contact with you sir?
@TheLostAndNotFound
4 жыл бұрын
Oh thank god! You're still doing these videos! I just got a CECHA01 60GB and I'm going to do my FIRST delid, following your videos. Do you recommend to delid the South Bridge chip? And do you recommend thermal adhesive to put the IHS back on? Thanks!
@NSC-Modz
4 жыл бұрын
Hello :) The Stourbridge is not need, just CELL / RSX and you good to go :) And for the second question, No, just do it like on my latest Videos, no need to glue them back ;)
@TheLostAndNotFound
4 жыл бұрын
@@NSC-Modz Thank you so much! You're awesome! I know you said painters knife is bad, but I only have painters knife for CELL and razor blade for RSX 😅 wish me luck!
@Dorianek8
Жыл бұрын
@@TheLostAndNotFound you did it?
@Evaldas256
4 жыл бұрын
You're gonna be making deliding tools for two days straight? I remember thinking making just one with sandpaper was hell :D
@NSC-Modz
4 жыл бұрын
Hahaha, yeah, but i got my tools to make other great tools ^^
@danthegreat7590
3 жыл бұрын
@@NSC-Modz how much are your cell opening tools ill order one
@xCarloson27
3 жыл бұрын
Please, name of tool for open cell that you used? I dont understand 100% english
@genericchannel9448
4 жыл бұрын
I am from The Netherlands have recently watched almost all of your video's! I tried to make your tool but I cut my cpu base and I could not get it thin enough and I think it was still too sharp! Can I please get / buy one of those tools from you? ;D (I have 3 phat Ps3's and I cleaned all of them and done fan mods and new mx4 thermal paste but the one that has no scratches and still has the box (CECHP04) model the rsx is around 55/60 degrees but the Cell cpu is hitting 81 degrees
@NSC-Modz
4 жыл бұрын
We on WhatsApp already, you welcome ^^
@مصطفىسعد-ص1و
4 жыл бұрын
I use cake spatula ( the small one) i curved its end and perfect to remove cpu IHS
@NSC-Modz
4 жыл бұрын
Yes, all works as long it's thin enough :)
@Aleksa.09
5 ай бұрын
whats that thing that you used to enter the hole of the cpu (at the beginning)
@jediofthejungle
3 жыл бұрын
In English they are called feeler gauges :)
@NSC-Modz
3 жыл бұрын
Thank you so much and you always welcome :)
@ISAIAS_Rincon
4 жыл бұрын
Espectacular explicación, hare mi propia herramienta, muchas gracias por compartir. Saludos desde Colombia
@NSC-Modz
4 жыл бұрын
Saludos meu Amigo :)
@occoronaramirez5844
Жыл бұрын
@@NSC-Modz Presio
@BrianTokyo
3 жыл бұрын
Maybe you could make a video on how you made that special tool
@NSC-Modz
3 жыл бұрын
Yes, I'm still working on it, will come in few days as i got time ;)
@ricardojesuscornejososa727
Жыл бұрын
Where I can buy the tools?
@adesign5
8 ай бұрын
I just used the .2 of this tool and removed the CPU lid successful. It no longer overheats. Hehe
@NSC-Modz
8 ай бұрын
Yeah bro. You welcome
@adesign5
8 ай бұрын
Just a thank you, without these vids I likely wouldn't have tried it and you saved my PS. Was running at 80c now on about 50c. Must say, I bent the .15, but was too soft. The .20 work very nice after sanding a bit sharp and attaching to the 1mm for strength. I made a tiny mark on entry. So happy at the moment 👍. You got new subscriber, got recommended from psx-place
@NSC-Modz
8 ай бұрын
@@adesign5 yeah, you always welcome :) Greetings to PSX Place also ✌️
@BombShock92
3 жыл бұрын
heute meine ps3 geköpft und scheinbar den cell mit der 0,15er lehre ganz leicht verkratzt, jetzt läuft sie nicht mehr... nächstes mal nehme ich die 0,10er lehre :D
@sherlanmamaril7368
3 жыл бұрын
What tool is that
@johndee759
3 жыл бұрын
I want to do this project.
@ΒαιοςΝταφουλης
4 жыл бұрын
Good job NSC how much you want to make for me a special tool for Ps3 cell and to send to me in Greece my friend?
@leotheakuma8485
2 жыл бұрын
Βρήκες άκρη; το έκανες;
@ΒαιοςΝταφουλης
2 жыл бұрын
@@leotheakuma8485 ti ennoeis an eftiaksa ergaleio?
@leotheakuma8485
2 жыл бұрын
Ναι και αν το έκανες delid τελικα
@ΒαιοςΝταφουλης
2 жыл бұрын
@@leotheakuma8485 delid to kana me diko mou tropo oxi me to ergaleio afto
@leotheakuma8485
2 жыл бұрын
Πως το έκανες;
@RedDeadSeries
2 жыл бұрын
Dude please sell me your tool please!
@RenoxMTA
4 жыл бұрын
8:34 XD
@NSC-Modz
4 жыл бұрын
What are you thinking about xD Bad Boy hahahaha
@MilekaRobot
4 жыл бұрын
Welcome back :) Great video! I need advice from you: I buyed a ps3 slim in working state, 2504 model. During play games the console was hot on the top (almost all surface of console), the fan was turning on normal speed and that is a little strange for me. I got a MX-4 thermal paste and started cleaning journey :D The console was never be opened, the warranty sticker was there. I was surprised how was clean inside, I may say almost without dust O.O And after s few attempts to remove IHSs I give up, it is too risky for me, do not want to scratch the processor surface. Removed old paste on IHS and put a new one. Now the console is muuuuch cooler, it is still warm in one part of console but less. I know that I must remove IHS from graphic and CPU chip for best results, but is there a way to check the "heat status" of console before YSOD? Maybe to install software for fan control and see temperatures of cores? Or just maybe to monitor the fan speed during play games? Thank you for the answer in advance in any case. All the best!
@Keiuran
4 жыл бұрын
Were those replacement 470 uF caps at the beginning on the cell processor? How did you make it so damn clean? Is there a video?
@NSC-ModzDE
4 жыл бұрын
Yes, search on my channel ^^
@Keiuran
4 жыл бұрын
@@NSC-ModzDE Which video is it? I've looked around and haven't found one where you do the capacitors in that orientation. They're side to side instead of up and down.
@NSC-Modz
4 жыл бұрын
@@Keiuran Those Caps on this PS3 model are already from Sony, but here is a Great Video on how to do it Nice and Clean: kzitem.info/news/bejne/0Xd4yoyLmIR1eXY
@InsaniaTHEGREATONE
4 жыл бұрын
Love these PS3 videos keep them coming :D
@NSC-Modz
4 жыл бұрын
Yeah, me to xD Thank you ;)
@cuttrogue
4 жыл бұрын
Please make a RSX removal one also!
@NSC-Modz
4 жыл бұрын
Look on my channel, i have a lots ;)
@cuttrogue
4 жыл бұрын
@@NSC-Modz Yes but we need an update! Do I need to heat the chip before using your method with razor blade or it's good even without heat?
@NSC-Modz
4 жыл бұрын
@@cuttrogue no need heat, but it works better to cut :)
@waynosdaboss
4 ай бұрын
Hi! It wasn’t clear what the tool is made from ? Or where can I get one ?
@knifelover1848
3 жыл бұрын
you got a new sub im currently in the proccess of doing that as well i did the gpu with no problem the ps3 still works but im to scared to do the cpu how do i get one of your tools?
@NSC-Modz
3 жыл бұрын
Hello and Thank you very much. For now i have no more told ready, but I'll let know as i got some more. Sry
@hspec1
3 жыл бұрын
Do you think using the 0.1mm (or smaller) metal feeler would work as the delid?
@NSC-Modz
3 жыл бұрын
Try to fit it in, if it gets easy in, than it's ok 👌
@evilnoey4873
4 жыл бұрын
I broke my ps3 trying this. Could I just pay you to send me a modded one?
@NSC-Modz
4 жыл бұрын
Sure man, just let me know what you like.
@rgbroot
4 жыл бұрын
Won + a subscriber what is the name of the tool you used in the video?
@NSC-Modz
4 жыл бұрын
You mean the nail file?
@c.r.m476
4 жыл бұрын
good for the disassembly but I would like to know what silicone is used for the processor and see an assembly, since it does not have videos of it and there are several disassembly videos
@Bayr0n
2 жыл бұрын
Hi NSC. Love your videos. I did your syscon video. I had ylod. Needed reflow on GPU And cpu is overheating. Do you sell the tool? I even have custom Fujitsu PC coolers on my ps3. GPU gets around 37 degrees.
@mrsinghtube
4 жыл бұрын
Hi NSC need ur help I tried the PS3 IHS removal and now it's ylod pls help
@Tagvillainy
3 жыл бұрын
N S C In The Place to BE !!
@NSC-Modz
3 жыл бұрын
He'll yeah xD
@rookie3528
3 жыл бұрын
Hey man, as always nice video tutorial! Was wondering if i could use a phone metal prying tool like the ones for the iphone and would it work as a CELL IHS removal tool?
@madsn1852
4 жыл бұрын
What sandpaper did you use to sand down the finger nail filer and I wish I could buy the fingernail filer from you lol
@sherlanmamaril7368
3 жыл бұрын
Is cech 2501 ihs can be remove or soldered type?
@johndee759
3 жыл бұрын
Can you ship to the US?
@shorty808100
2 жыл бұрын
Why wait just make one at home yourself
@NSC-Modz
2 жыл бұрын
If you can, do it, if you want something professional buy my tool ✌️
@AngelKsiezyc
4 жыл бұрын
I followed your instructions removed IHS and replace thermal paste but now it does not start anymore. Red light is blinking :( Console was working with a lot of fan noise before that. Any idea to fix it?
@NSC-Modz
4 жыл бұрын
i bet you have scratch the Cell... This should be practiced befor doing that, thats why i always say: Take Care doing this stuff
@AngelKsiezyc
4 жыл бұрын
@@NSC-Modz optically is perfect. I did it twice in 2 mainborads with same result.
@NSC-Modz
4 жыл бұрын
@@AngelKsiezyc Than you do something wrong, are you talking about the CELL or RSX? It´s just enough when you break a small smd part...
@AngelKsiezyc
4 жыл бұрын
@@NSC-Modz I have got 2 consoles I did lid Cell and RSX on both motherboards. Red blinking light in both
@NSC-Modz
4 жыл бұрын
@@AngelKsiezyc how did you remove the RSX IHS?
@ruthlessc95
4 жыл бұрын
Eu tentei fazer com uma lima pequena de metal porque não encontrava outra e não consegui tirar, acho que fiz merda porque tenho ideia que estraguei a parte verde do cpu
@NSC-Modz
4 жыл бұрын
Hmm, acho também que está estragado agora 😔
@ruthlessc95
4 жыл бұрын
@@NSC-Modz estou aquecer com um estação de ar que te e mesmo assim não consigo tirar
@ruthlessc95
4 жыл бұрын
@@NSC-Modz consegui tirar mas como disse fiz marcas na parte verde do cpu
@NSC-Modz
4 жыл бұрын
@@ruthlessc95 podes deitar au lixo agora ^^
@ruthlessc95
4 жыл бұрын
@@NSC-Modz acabei agora de fazer delid, ps3 liga e entra no menu (antes disto fazia o ylod) mas do nada desliga se, não sei se o cooler está a fazer bom contato com os chips, parece que o metal plate não deixa encostar, eu também não meti os parafusos todos porque queria só testar.
Пікірлер: 94