Nice, just did my first attempt earlier and it was successful 👍my little brother has been losing it because his DualShock 4 has drift 🤡 I got a spare ps5 analog and placed it in and it worked perfectly
@IceofDream.
Жыл бұрын
Im waiting for my heat gun to arrive but about sending some components to the space
@dannyboy643ify
Жыл бұрын
@@IceofDream.be careful with the power connector, i managed to melt it off but then i soldered it back on 😂
@theanc316ientone
2 жыл бұрын
You make it look really easy.
@tomaszkluska6419
Жыл бұрын
Try it.
@dh123ize
7 ай бұрын
just practice on a junk board i failed mt first attempt because i was afraid to melt the plastic connectors
@mcfriedchicken1972
Жыл бұрын
Solder wick never works like that for me. Even if I add flux. What temp you using?
@excusemerl7766
Жыл бұрын
How hot are u using the heat gun that u didn't damage the motherboard??
@ICEknightnine
16 күн бұрын
I'm not an expert but why couldn't you use the wick to remove the solder connections instead of using a heat gun? considering how much you had to use the heat gun to get the connections out.
@octavionicolini3779
3 жыл бұрын
Hi, nice video, I'm trying to learn soldering to start fixing my own stuff, and I need to know the name of the copper material you use to remove the tin out if the board. I saw another guy doing it with a pen shaped thing that sucked it, and I don't know the name of either. Thanks in advance.
@zombiesroflcopter
3 жыл бұрын
Pen is solder sucker. Copper Braid is called Solder wick. Most solder wick comes infused with flux, but adding more wont hurt when desoldering. Cheers
@EnjoyTheSilenc3
Жыл бұрын
do i need a solder sucker? and do i need a heat gun to remove the potentiometer?
@jonaa98priim35
10 ай бұрын
@@EnjoyTheSilenc3no
@ronijacinto9944
2 жыл бұрын
that was clean
@sage6459
Жыл бұрын
finally n snacking to the point video
@VijayChauhan-lm2gs
Жыл бұрын
i replaced it but it didn't work for me. same issue happened. any other solution or any other problem with my controller ?
@xfreaks-ne4cp
3 жыл бұрын
may i know the setting for the hot air? thanks
@allservice5506
3 жыл бұрын
Temp-450⁰C Air-5 from 10
@LordFarquaad-1428
3 жыл бұрын
I tried his settings and had no luck maybe I was impatient but I figure 1-2 minutes of air time or its not coming off
@tlayn4
3 жыл бұрын
I tried 350c and it melted the analog before it melted the lead but I was able to get it off. LOL
@eynnercuevas2261
3 ай бұрын
My Dualshock 3 has a problem with both analog sticks, when I play for half time both sticks stop working what could it be?
@310shadow310
Жыл бұрын
What wick are you using and what solder did you add to it? I failed my attempts to resolve rmine
@bigdaddycool4030
3 жыл бұрын
Can I ask what air gun you got thank you 😊
@Dustinmh23
2 жыл бұрын
Hello I'm having a really tough time finding the 4 pin actuator for the ps3 du shock controllers. Any chance you have a link to where I might find them?
@sparda1418
2 жыл бұрын
You can find it on AliExpress
@mm_bnf
3 жыл бұрын
sir what's the difference between blue joystick and orange is orange better? i have a blue one and it's broken now idk what to buy
@allservice5506
3 жыл бұрын
Buy orange with F logo on ebay or aliexpress.
@ll_avail_ll9050
3 жыл бұрын
Do you really need to use a heating gun ?? Or can I just use the wick to collect the solder
@VentwosWingblade
2 жыл бұрын
You can use the wick, it just takes a tad longer. Make sure to use flux before.
@rafaelfrigillana634
3 ай бұрын
Could you do that with a standard heatgun?
@Hammer143
3 жыл бұрын
I couldn't do it, the hot air temp is 400⁰C and the analog stick won't come off, it doesn't even move ffs
@allservice5506
3 жыл бұрын
Rise temp to 450⁰C.
@Hammer143
3 жыл бұрын
@@allservice5506 I'll try, thanks
@JonathanHernandez-nc1lu
2 жыл бұрын
Do you knew how to attach the red and black wire back on
@brandonau9875
6 ай бұрын
Temp and fan speed on the heat gun?
@ps3iznajmibeograd626
4 жыл бұрын
Nice work.
@tonipolster2839
Жыл бұрын
Habe ich bereits schon selber gemacht. Nur sind die Controller echt sch..., bei denen die Sticks nur gesteckt sind und nicht gelötet. Die Folie wieder an alle Kontakte zu bekommen gleicht einem Glücksspiel.
@dxrk_kua8233
2 жыл бұрын
mann u should’ve put calming music
@orenji_.
Жыл бұрын
what a type your blower ??
@pcysneros
3 жыл бұрын
But where do you buy the joystick module?
@knightstemplar6835
2 жыл бұрын
ebay mainly
@2litttv891
2 жыл бұрын
Is That A Copper Strip?
@ArchiURURU
2 жыл бұрын
Iron temp? 🤔
@xirtoofficial5056
3 жыл бұрын
Can you say me the names of the things tha you used
@fixing_ing1137
3 жыл бұрын
After replacing the stick somehow is never cebtered correctly...do you know a calibration tool? Or something like that
@soydan5057
3 жыл бұрын
bend the tails
@hmdak
3 жыл бұрын
@@soydan5057 what bend the tails?
@loneifiwont3467
3 жыл бұрын
How much would this cost ?
@EmirDessu
3 жыл бұрын
A joystick cost 5 dollars but the equipment to fo this is like overall 60 dollars but its worth it, when you think that you do it.
@Zextakos
3 жыл бұрын
I can do it and without flux?
@theanc316ientone
2 жыл бұрын
Mine went good up until about 2:10. I couldnt get passed this part, the copper would not absorb all of the solder.
@KnorGamingNL
2 жыл бұрын
Try adding some flux to the wick
@lopeiaran3422
Жыл бұрын
The liquid that you sprayed on the paper is just water, correct?
@shubhamtayade6579
Жыл бұрын
ISO PROPANE ALCOHOL 99%
@allservice5506
Жыл бұрын
Alcohol, not water.
@lopeiaran3422
Жыл бұрын
@@allservice5506 ahh okay thank you
@iqbalhusain4995
Жыл бұрын
how many watt solder iron which you are used?
@allservice5506
Жыл бұрын
70 watts.
@St4yS4fe
6 ай бұрын
hey can u tell what temperature u using
@St4yS4fe
6 ай бұрын
for heading and for loting
@mrgodspeed6725
3 жыл бұрын
i changed one analog one with f logo but l3 drift to downward
@hmdak
3 жыл бұрын
Same man
@boskosks222
3 жыл бұрын
I did thia and now the drift goes to the left and wont stop how do o fix this? Or what did i do wrong. I also put in a new joystick but it keeps moving to left in game
@bryantv7013
3 жыл бұрын
That happened to me too and I don’t know why that happened!
@bryantv7013
3 жыл бұрын
Where did you buy the stick from and what’s it called?
@hmdak
3 жыл бұрын
Same issue kinda sad the the creator of the vid doesn't even bother responding to the actual comments asking valuable questions.
@terellmccray9189
2 жыл бұрын
I have severe tendinitis and can only play with the hori mini ps4 controller because of this but the sticks have too much tension and cause my thumbs too become tired fast. Does anyone know a company or person i can pay to have the tension reduce in the thumbsticks to that controller? Anyones help would be much appreciated
@AlejandroGonzalez-vs7lq
2 жыл бұрын
There's a video were they show how to change the spring for the anolog stick. You just have to buy it.
@sa7oshi
Жыл бұрын
Anyone knows whats the name of the liquid flux he uses for desoldering?
@allservice5506
Жыл бұрын
Amtech 559
@xx_ars_enic_xx2831
4 жыл бұрын
Lol no smoke from the flux must be magic flux I need the name and no heat tape to protect other components
@allservice5506
4 жыл бұрын
It is chinese low price flux, no need for tape. I rearly used tape to protect other components. Flux is chinese copy of amtech.
Пікірлер: 75