I ordered all 4 turbo coolant lines on my 2013 GL450. I only received and replaced 3. The last one I need was canceled. Could find it at any MB dealer or even aftermarket. Dealer told me it could be a few days, a few weeks or a few months until the part arrives. Luckily I was able to repair it using parts from the other old lines and RTV gasket maker. Looks OEM, holding good and my GL450 is on the road again.
@drumluck69
Жыл бұрын
Good video but missing key part...the way you disconnected the coolant lines from turbo? I have same problem on wife's s550. Plastic pieces broken and leaking coolant. Just bought all 4 pieces from MB dealer and spent $374. Ouch!
@exodusmovement4596
Жыл бұрын
The driver side turbo is harder to get to the lines. If you can see passengers side turbo it is more clear. I believe its a 17mm bolt. Short socket 3/8 ratchet wrench, for the driver side your best bet would be from the bottom. Lot’s of parts on top side of motor to remove to get to the center bolt. Space very tight. Be patient.
@MrMaineprince
2 ай бұрын
Great video! I'm working on a 2012 Mercedes S550 with W221 engine... attempting to replace the Driver's Side (left of engine) two (2) turbo coolant lines. I replaced the right one... but now seeking to replace the left. Question is the black plastic that broke off from going into the water pump... what size is the bolt holding that plastic piece together. Is what hiding behind the pulley - is that easy to get to after removing the serpentine belt. I can see the black plastic but tracing it to the engine, it seems impossible to reach due to heat shield.... and I can't see the bolts (from the top) where it's holding the coolant line in place. I heard you mention an "L" Bracket... but unsure if that's the same in W221 engine. Thanks in advance for your feedback. And Much appreciated your willingness to share with others.
@exodusmovement4596
Ай бұрын
Hello and so sorry I haven’t seen your messages. You have already fixed this issue, but yes there are two pulleys that are in front of the lines, the bracket is one that is holding the lines together and there is one underneath the A/C compressor that attaches to the engine block.
@Fiaztheking
10 ай бұрын
Hey man I just want to know how many lines should be replaced if you want to do all of them and what are the names of each piece?? Cls550 benz 2012
@exodusmovement4596
10 ай бұрын
The names are turbo coolant lines. L/and /R. And yes I would replace them both if you have twin turbos. They sit on top of each other in two places.
@jeffreycicero6685
3 ай бұрын
Hey, how many hours do they give to replace all 4 Turbo coolant lines and the thermostat and the water pump and bleed system? I gotta do this job.
@exodusmovement4596
3 ай бұрын
I think it’s about 8hours flat rate. But honestly it will seem like more. But take your time and see what you are doing. Have a lot of silicone and PB blaster spray..
@Stevehall2112
10 ай бұрын
What would that job cost with parts and labor like an estimate.
@exodusmovement4596
10 ай бұрын
Some where in $2500.At the dealership.
@chasefambino461
6 ай бұрын
Can I email you a video of a leak I have so I can figure exactly what the issue is before I take it in?
@exodusmovement4596
6 ай бұрын
Exodusmovement339@live.com
@mlbking1616
4 ай бұрын
If i only need to replace thermostat ..what do i need to take off to complete job?..or can i complete job with out taking off anything ...thank you sir your help is much appreciated..
@exodusmovement4596
3 ай бұрын
It will depend on the model engine we are working with. In the video you would have to remove, serpentine belt, and upper radiator hoses, and that’s where you will in counter the jointing of the turbo coolant lines. They are close enough that you can easily break them. Advice torx bit 8-12mm E. 25-45mm T. The thermostat housing has 3 bolts on the head and 2-3 depending on model on the extended area. If I think of more I will let you know.
@mlbking1616
3 ай бұрын
I have a 2014 gl550..which looks almost the same or maybe is the same set up...thank you
@michailaarmstrong685
7 ай бұрын
We have all of the parts. But we cant get the turbo lines off. The heat shield is in the way. Any way to get that off or move it?
@exodusmovement4596
7 ай бұрын
Quick question are you working on the drivers side of the motor? And are you removing the lines on the turbo?. If it is on the turbo spray p/b blaster and try to between one of the lines and pry gently. Remember they sit one on top of each other so one has to come out first. Which one are you trying ?
@michailaarmstrong685
7 ай бұрын
Yes. Replacing all of them, we are just working on the drivers side right now. The parts store ordered the wrong part so we are waiting on the second one to come in now. We are just trying to get it to come out.
@michailaarmstrong685
7 ай бұрын
We are trying to get the bottom one to come out first. We are pretty sure that's setting on top of the other one.
@exodusmovement4596
7 ай бұрын
You can not see it. The heat shield is there, I will take it that the center bolt is removed. There is a bolt underneath the turbo, and there is a bracket holding the two together.
@exodusmovement4596
7 ай бұрын
Check from the bottom looking upwards and you will see the bracket holding the lines to the turbo
@user-gi5ld2ke8o
10 ай бұрын
How did you get the lines loose on the side
@exodusmovement4596
10 ай бұрын
Good night, how would be a lot to say and for you to read, but I did a video with the Mercedes twin turbo valve cover reseal and the how to get to the lines. Thanks
@user-gi5ld2ke8o
10 ай бұрын
@exodusmovement4596 I saw the video but I have everything off but can't get the connectors out the drive side, bolts are out but the part that in the turbo can't get out
@exodusmovement4596
10 ай бұрын
It is one on top of the other. I think or if remember the one on the bottom has to come out first. One bolt in the center of two lines.
@exodusmovement4596
10 ай бұрын
Spray a lot of WD40 or PB Blaster
@user-gi5ld2ke8o
10 ай бұрын
@exodusmovement4596 I understand but what tool did you use to pull them out.
@johnvan1640
4 ай бұрын
Like your video but you don’t have any footage of your work. Just pointing 🥹👎
Пікірлер: 35