Liked the whole assembly, nice job. One thing I would recommend is a radar mast, as that's really a must when you have an offshore boat. The other recommendation is that the antenna's need to go up on the mast as your radio signal only goes as far as the antenna is high. Roughly for every 16 feet an antenna is in the air you get 1 mile of communication by radio.
@Micington
3 жыл бұрын
Looks bloody strong with all the stringers!
@valleycrew3
3 жыл бұрын
It definitely has a very strong structure, I am very impressed with the design and simplicity of it.
@gerlanaraujo1527
Жыл бұрын
Sensacional projeto ficou da hora, bem arrojado, um investimento grande mais de muito bom gosto. Parabéns boa sorte 👏👏👏👏👏,✌️💪👍👍❣️❣️
@daviddecalmer654
3 жыл бұрын
Well done mate, be good to see the finished boat, great job
@valleycrew3
3 жыл бұрын
Cheers Dave, hope to have a new video up shortly
@rasimpirishov6155
3 жыл бұрын
Excellent 👍👍👍
@JohnSmith-xq6cv
3 жыл бұрын
bravo
@kakakhail2643
3 жыл бұрын
Really inspiring, Thank you for the upload. What is it that Mariton Marine will do? Be great to see it finished.
@valleycrew3
3 жыл бұрын
Thanks Kaka, Mariton Marine is a aluminium boat building business but unfortunately they could finish my project. Like for me the guys (Daniel and Jacko) at Metal & Marine have taken on the job to complete of the fabrication work.
@hendrilasjaya
2 жыл бұрын
🔝
@augustoduminuco4683
3 жыл бұрын
That frame is supper heavy duty, only thing I want to know is if it's too Ridgid wouldn't it start to crack?
@williamphillips9615
2 жыл бұрын
Good possibility… but with the load dispersion, I really don’t think it’ll be too much of an issue.
@srtsrt2531
3 жыл бұрын
👍👍👏👏
@Mohammed-dl9bc
2 жыл бұрын
Brother is the almonum you use is alloy ?
@dhirarcharef6038
2 жыл бұрын
I would like a chart and dimensions of this boat if possible (pdf)
@projektmedalexander3206
14 күн бұрын
Does anyone know how to remove the flaming surface of the plate? can you use any means to get the plate in one and the same surface. I don't mean painting the hull, just being able to have the hull not painted only aluminum colored.
@rtyhgfplmkoi4784
3 жыл бұрын
600 outboard?
@lasol2474
Жыл бұрын
Nice! what is the thickness of the hull? what is the welder that you used and does it require 3-phase power?
@valleycrew3
Жыл бұрын
It 6mm plate for the hull, 4mm sides. Welder is 270WIA mig welder, 3 phase required.
@lasol2474
Жыл бұрын
@@valleycrew3 Thanks mate!
@murraydaniels3377
3 жыл бұрын
Is your welder a double pulse Mig?
@valleycrew3
3 жыл бұрын
Single pulse welder
@SLfamily1
3 жыл бұрын
That is very good and good work men. I need to ask u , how could I get find a book or design to build a boat. Could u tell me if it possible. Thanks Sirak from Norway.
@valleycrew3
3 жыл бұрын
You will need to purchase it from PureKraft. purekraftboats.co.nz/
@VRTOC
3 жыл бұрын
@@valleycrew3 can´t see any book there.
@corvavw6447
Жыл бұрын
Saai ontwerp daar zou ik meer werk van maken.verder ziet het er redelijk uit.
@user-mc2mc9wh6b
7 ай бұрын
May i borrow your general arrangment that boat
@CaptainDayne
3 жыл бұрын
I have a question was the hull put in an oven after final weld ? Stress cracks plague aluminum boats if not heated. Experience here!
@valleycrew3
3 жыл бұрын
Yes after the full longitudinal welds have been completed
@Micington
3 жыл бұрын
Handy to know that. Good question
@CaptainDayne
3 жыл бұрын
@@Micington yeah man i spent 13hrs on the top of the bottom of a Munson boat due to stress cracks, and the fwd bulkhead had no limber holes, or bilge pump. Compartment filled up while running with cargo onboard. Capsized in 40deg water ,35kt north winds Munson just welds the boats no oven time.
@Micington
3 жыл бұрын
@@CaptainDayne geez. Glad you’re ok! Were you with someone else too or by yourself? Did you learn the heat treatment after you got back safe? I’ll think twice about boat repairs to tinnies!
@CaptainDayne
3 жыл бұрын
@@Micington yeah had 2 deckhands with me We are ok. Hugged it out all night. Bodyheat that was 2018 december 21. The day of the government shutdown. Coast guard called twice 1am and 3am by ship pilots. They never came. Got rescued by a tug and barge at 730am. We departed at 630pm the previous night.
@celsonjuniorsantossampaio6817
3 жыл бұрын
Peu tu donner le liens pour les plan merci
@valleycrew3
3 жыл бұрын
Sorry there’s no link. I brought the plans, mate
@msgboatbuilding5482
3 жыл бұрын
wht software use for crate this design?
@steviebee1989
3 жыл бұрын
Is this English? Perhaps you are asking which software did you use to create this design?
@fisheater844
3 жыл бұрын
Yes Steve I’m sure that’s what he is asking.
@msgboatbuilding5482
3 жыл бұрын
@@fisheater844 yes,,,,
@valleycrew3
3 жыл бұрын
I am not sure what software programme Purekraft are using. Check out their website. purekraftboats.co.nz/
@Tha_bro
Жыл бұрын
whats the price like for something like this?
@valleycrew3
Жыл бұрын
For the flat pack kit with trailer, is approx. $50k
@impuls00007
Жыл бұрын
Where can I find cnc files and drawings???
@valleycrew3
Жыл бұрын
You need to purchase the files from the boat design HMD
@nadjimousseneali4965
Жыл бұрын
Bonjour ! vous acceptez quelqu'un de venir apprendre ?
@user-yt3to6oz6k
10 ай бұрын
0:21
@zainmblitar
2 жыл бұрын
Just a photo... Not a video bro... I have too bulid aluminium boat at my chanel.... Greeting from Indonesia.
@chhotetharu3699
3 жыл бұрын
Nepal ok
@gulbertnurse4308
3 жыл бұрын
Hi Br would like to come and build me one in South America lets talk
Пікірлер: 56