Get your BACK TO THE BANDO t-shirt from FPV Crate: bit.ly/3OZTsiA
@BB-jq6ek
2 жыл бұрын
that's funny I hit your Amazon link and bought the smoke stopper and 2 minutes later that one blew up on you... should I return it and wait for a better version?
@cajah1000
2 ай бұрын
Just want to add in you can still get your motor tones for all motors. Had a ground short on my brand new AIO and all motors still toned so be careful because if you keep the unit armed it could send that stinky smoke from the motor or blown fet. Still researching my recent and years of these issues but recently watched this one. It will probably lead to me changing the fet or spare part pile.Thanks JB for all your time researching and assisting all the hobbiest.
@metalx9499
2 жыл бұрын
Turns out my twitching problem in flight was simply a de-soldered capacitor. The negative side had broken lose from the ESC negative Vbat pad. In flight the broken leg of the capacitor would tap the vbat pad and release its energy causing the twitch. Hope this helps someone. Cheers Barry
@pwillie2288
2 жыл бұрын
I just went through these steps yesterday. Glad to see i checked everything how the master does it. In my case. One motor would idle fine (props off) and rev to about 20% throttle then cut out. Props on, the motor would begin to idle then twitch out and stop. Turned out damaged/broken wire to motor and I suspect this limited the current that could be delivered.
@Joshuah2012
2 жыл бұрын
The number of posts where the person’s motor isn’t spinning or is twitching with PROPS ON INDOORS on the multirotor subreddit the last few days has been insanely high. Now I can link this video along with telling them they’re kinda dumb for arming inside with props on with a known issue on top of it
@NickCabinet
5 ай бұрын
MY SMOKE STOPPER IS FRIED TOO!!!! I WENT TO HELL AND BACK, UNTIL I WATCHED THIS VIDEO!!! Now all works, as planned....WOW! Thx Bardwell!!!
@pi.actual
6 ай бұрын
Always keep your guard up. I recently had a motor on a little 3D printed Cub that I built and with the prop on I noticed it seemed to be turning backwards. So with the throttle fully closed I came up with this brain fart idea that maybe I needed to reverse the throttle channel on the transmitter. Well the second I did that it instantly went to full throttle (still in the same reversed direction) and the entire nose of my model virtually exploded into a million pieces right next to me. Luckily I was uninjured but after cleaning up the mess I noticed the motor no longer worked. The wiring looked okay but it just wouldn't turn. So I bought a new motor and guess what - same thing. I bought a new ESC and still no joy. The throttle channel was in Normal (not reversed) but when trying to calibrate the ESC I noticed it was working backwards. In order to get it to calibrate I had to start with throttle lever fully closed then move it to fully open and then it worked but the throttle channel was operating reversed even though it was in normal mode. I finally had to again hot switch from normal to reverse (this time with no prop) to get everything back in sync. It had me scratching my head for about a week. Motto is - BE CAREFUL
@rodrigodiniz13
2 жыл бұрын
Joshua, the black wire from the XT60 of the smoke stopper got broken in the middle of the demonstration.
@hultaelit
2 жыл бұрын
Yeah, can see it at 19:16 before the multimeter covers it up
@JoshuaBardwell
2 жыл бұрын
Wow! That's great to know. I can fix that easily!
@TempeiB
2 жыл бұрын
I've seen why your smoke stopper doesn't work; 17:25 the ground wire broke. At 19:15 you can see it better.
@BrysonWooden
2 жыл бұрын
I'm literally dealing with this exact issue with my quad right now, thank you for making this video!
@ShaneGraham057
2 жыл бұрын
I think JB has a bit of the psychic going on in the community. I too am dealing with similar issues (but further down the rabbit hole) :p
@h3rtz
2 жыл бұрын
same here. spooky!
@jamesburton8348
2 жыл бұрын
haha same. my motor went yesterday
@jeramboo8511
2 жыл бұрын
This happen so many times, I have an issue and the next day Bardwell made a video. You gotta love him❤️
@tourisew7513
2 жыл бұрын
Great video, I just have a bad motor right at the instant, it spinned about 10 seconds and than completely stopped.
@kurtzFPV
Жыл бұрын
2:23 Joshua's Tarantino impression from Reservoir Dogs.
@marcinsamotyja
2 жыл бұрын
This is the 4th time I have a problem and less than 24 later your newest video helps me
@brixzereg
2 жыл бұрын
Dude your vifly has a wire disconnected you can see one wire from the board to the xt60 has come loose. That's why it stopped working.
@veram.2460
2 жыл бұрын
in my case stator was unglued from the base and moved about 15 degrees forward and backward. Thar caused motor lost sync in air and quad fall from sky. Works prefectly on the ground - takeoff - crash. Well. I replaced ESC - guess - didnt worked. then at the next turn stator just ripped wires off, shorted it and burned ESC.
@metaldirtnskin
2 жыл бұрын
Turns out LED racewires, as well as looking cool, let you see the motor beeps clearly which can be handy for this kind of troubleshooting 😁
@Nam_flies_drones
2 жыл бұрын
love when joshua from the future comes in, hes so wise
@eatyourvegfpv
2 жыл бұрын
Hey JB, I'm not sure if you remember or not but about a week ago you showed a video of mine with a motor issue, where one motor would run for a few seconds than 'reset' in a perfectly rhythmic way... I replaced the ESC and that cured it 👍 Just wanted to let you know as it's relevant to this video.
@SunriseWaterMedia
2 жыл бұрын
I've told you before, and I'll say it again: you have the best username! 😂🥦👍
@eatyourvegfpv
2 жыл бұрын
@@SunriseWaterMedia Haha! I do remember! And thank you 😉💚
@МихаилЛосев-п1ъ
Жыл бұрын
Hi, can u just help mi a bit? How can I replace esc? I am begginer, and have such problems as u)
@maxtrixbass
Жыл бұрын
Dang that was helpful. Its hard to get such clear, concise information in the world of electronics for those of us without electronics degrees. Thank you.
@himanshubajaj3501
Ай бұрын
I have a motor twitching but it runs on higher RPM. But if it doesn't rotate initially it will not spin at night RPM as well. So higher RPM just runs it and can go to lower rpm from there
@skyweaver3199
2 жыл бұрын
Hell of a prop tool there buddy
@FireN2k9
2 жыл бұрын
Next video "Motor repair/rewinding" Would be a waste to throw that mechanically fine motor in the trash. :)
@lemonsquareFPV
2 жыл бұрын
Agreed! Even though it takes 10 minutes to completely redo a motor I don’t think most people bother, among my flying buddies, it’s just me and one other person that rewind our motors. We are the FPV nerds among the group :p I like how I can change/customize the KV and I try to be wise with my use of resources on this planet. That being said I am lazy and don’t fix them right away if I have a spare on hand, I usually collect a bunch (4-6 usually) and then I do them all at once.
@dhbfpv
2 жыл бұрын
Holy timing, another incredible wealth of knowledge shared. You are a treasure sir, if I had friends I would share every video you make.
@dingbatfpv
2 жыл бұрын
Dead smokestopper? No. It's a "troubleshooting opportunity"
@Andyblalock
Жыл бұрын
mine every once in awhile will spin up.. the rest of the time it doesn’t and sounds like it restarts by doing the final two beeps again..
@tonyvladi9940
2 жыл бұрын
From one genius in youtube if esc for 1 motor if died on your 4 in 1 ,you can make 3in1 and 1 , buy separate esc control and sold it direct con power of battery line, and with testing in betaflight in pc(motor testing) find a control signal cable for motor what you need. I repaired my emax hawk pro with this idea.
@AvallonYo
2 жыл бұрын
That’s like putting a carb on top of you’re fuel injector and saying you made it work…
@sufysprojects2689
2 жыл бұрын
JC? PbF?
@MrSabram07
2 жыл бұрын
?
@Wheelieking619
2 жыл бұрын
Thinking outside the box! Bravo chief!
@Voyajer.
2 жыл бұрын
@@AvallonYo one of the few times where the saying if it's stupid but it works, it's not stupid is appropriate.
@Dosclic98FPV
2 жыл бұрын
Fried an ESC on Sunday and it took one of the motor into the grave. Gonna do some rapairs this weekend. RIP P.S. Seems you did not mentioned to check the continuity between the positive and the single pads of your ESC, in my case I saw there was a short on the positive and one of the pads so if I would have connected another motor to test I would have killed another motor.
@Dosclic98FPV
2 жыл бұрын
@@mikebergman1817 Yeah, I am still today seeing the cost of the repair lol. It was a Mamba 40Amps not soft mounted and died in full acceleration so maybe all the factors combined took to this point. I also have to mention that it died from the side I took the first and last hard hit back in January.
@ruvyfpv4398
2 жыл бұрын
So I fried a motor months ago ordered a few motors and installed the motor and plugged it in and no smoke then I spun the motor up and the motor started smoking again on the new one:/ so I’m assuming it’s a fried ESC? It’s a Diatone Roma F5 Any help would be awesome!
@JoshuaBardwell
2 жыл бұрын
That test is in the ESC troubleshooting video linked in the description.
@Dosclic98FPV
2 жыл бұрын
@@ruvyfpv4398 Yeah, check for continuity but that is the ESC almost for sure
@bitterrootfpv2207
2 жыл бұрын
@@ruvyfpv4398 sorry dude. But your assumptions are correct.
@wearemany73
2 жыл бұрын
Another brilliant video JB, these bread and butter clips are required veiwing for new FPV pilots and old FPV pilots alike. 😊
@neuroticsdubstep
2 жыл бұрын
Solid video. You went over everything really clearly. One thing I’ve rarely run into is having just the first 3 beeps and missing the last 2 FC beeps intermittently. 75% of the time it works and flies fine. Sometimes I don’t get the beeps. I think it’s a delay on my FC initializing and sending throttle signal in time. Only had it happen with a particular FC/ESC combo
@3DIYOriginal
2 жыл бұрын
Awesome Video !! Love the way, you explain things on your KZitem channel. There is a lot of usefull information (data) on your channel. I'm from Spain (Valencia), here is 03:32 in the morning & I'm watching your video. Can't stop watching your videos. Hello to everyone !!! 😎 THANK YOU FOR SHARING YOUR KNOWLEDGE WITH US!! 👍🏻👍🏻👍🏻😎
@jejefpv
2 жыл бұрын
Something that often occures when testing with a smoke stopper is that it detects a short once or twice in a row and then it works as expected, it is related to the capacitor(s) which are getting charged. Another topic that would be very interesting : these last months I got into too many bad gyros (much more than before). Do you know an effective way to troubleshoot a gyro on the bench ? I had bad gyros that induced "grinding noise" from the motors, even with no props, that was easy. But I had other bad gyros which were terrible on one or 2 axis, but only a flight with BlackBox could highlight the issue. Thanks Joshua.
@MCsCreations
2 жыл бұрын
Hey Joshua, which is your electric screwdriver? Seems pretty good! I've been thinking about getting the one from Xiaomi, but I'm not sure yet.
@plumpitiful5856
2 жыл бұрын
I think the DeWalt gyroscopic is best.
@adamwilson2345
2 ай бұрын
ahhhhh props off bardwell ok ok fair enough.
@flyv3rse753
2 жыл бұрын
Wow JB I literally just got this problem, I was out flying and when I switched to the Skyeliner, exactly the same kwad you are showing I had a problem with one of the motors, I don't know yet what it is but I noticed the color in that one is more yellowish as the one in your video. Thank you for posting, I have to figure it out and I should order a new motor. Question, would this motors be affected if flying the quad with a 5s lipo?
@petrsovis
2 жыл бұрын
Hello Joshua, can you help me ? I just bought Darwin FPV Baby Ape, when I connected receiver (ELRS EP2) and when I connected the battery (it was 2S and drone was 2-3S) it smoked. ESC's circuit (FET) smoked. I measured motor - it has much lower impedance than other 3 and when I spin it (with motor screw driver) I get 1/3 of voltage of others. Could motor cause ESC to burn ? The whole setup is stock from DarwinFPV (1104 $3 cheap motors). Could motor be bad from factory ? Or ESC ? FC+Esc's not cheap on those copters. THANKS ! Love your channel. Petr
@TechnicallyTom
2 жыл бұрын
Those motor screws look too long. There’s maybe a millimeter or two of clearance. Ideally the motor screws would be flush with the top of the mount holes. Although there seemed to be some clearance, the inbound motor screws might be touching the wires. The threads could cut through and cause a short. Watch the part of the video where you zoom in on the motor.
@keithplayspc
2 жыл бұрын
listen, sir...those are MR. Thirty connectors :P sorry, couldn't resist, lol
@edwright8279
2 жыл бұрын
Just solder on a good motor to see results
@RichMoore-tweakin7376
2 жыл бұрын
Josh from the past, you should have done this video 5 years ago. In the past 4 years I figured out how to troubleshoot but this video makes it very easy. You've got some amazing points.. thank you so much for all your hard work
@williamlosch
2 жыл бұрын
looks like @ 17:19 the xt60 ground wire is loose on the first Vifly shortsaver!
@pexagaming5669
2 жыл бұрын
19:17 haha you ground wire on funky board thingy to XT60 is just disconnected. Lol. Thanks for the vids btw.
@Ryet9
2 жыл бұрын
Glad you covered the RESOURCE(s), was recently was helping someone diagnose a problem of 2 motors not working/showing in BLHeliSuite.. turned out that the "auto detect" feature of betaflight's firmware flasher had detected TMOTORF7 as TMOTORF7V2 (or was claimed to at least), so the motors didn't have the expected resource due to the applied "DEFAULTS" EG: < board_name TMOTORF7 --- > board_name TMOTORF7V2 < resource MOTOR 1 C06 < resource MOTOR 2 C07 < resource MOTOR 3 B00 < resource MOTOR 4 B01 --- > resource MOTOR 1 B00 > resource MOTOR 2 B01 > resource MOTOR 3 B04 > resource MOTOR 4 B05 💌️
@rgross989
2 жыл бұрын
Great Videos! Please keep more trouble shooting videos. So much is learned even outside the topic.
@maplefpv
2 жыл бұрын
that vifly didnt die, the gnd wire just gave up lol @17:25
@crazzyiam4640
2 жыл бұрын
Can I go with rcinpower v2 2207 1857 for my 5" drone or suggest me any other motor i am from India 😇😇
@JoshuaBardwell
2 жыл бұрын
Those are great motors.
@bohdanshcherbak6303
2 жыл бұрын
From the first moment i've seen the smoke stopper with the negative cable disconnected I was begging you to see it
@DarrenAllatt
2 жыл бұрын
4:05 looks like there may be a short or potential for one between the bolt and windings under the motor.
@RLeeVisuals
2 жыл бұрын
You Da Man!
@bebenoeg5188
2 жыл бұрын
Thanks for the knowledge, I really appreciate it. Hopefully it can continue to provide useful lessons for all of us. Hope you are always healthy, thank you JB, have a great day.. 😊👍
@ludofevrier5593
2 жыл бұрын
Ça c est un tournevis électrique américain 👌🏼😂
@UnfairFrame653
2 жыл бұрын
i did enjoy the video
@basmajianmiscellany113
2 жыл бұрын
JB, great video. Simple troubleshooting with explanation along the way. I've always wondered how to check those hard to turn motors. Way to have Joshua from the future show the humanity and confusion troubleshooting sometimes brings. Nicely done.
@davidcasillas2131
Жыл бұрын
i had 4 vfly smoke stoppers take a crap on me.
@EdwardChew
Жыл бұрын
I have a case where the ESC is burning up the rear left motor 1. so it started twitching 2. i replaced the motor 3. less than 1 fight, it flipped itself, same rear left motor become twitchy So I put both motors to an independant esc later, they twitch. indicating motor is faulty now On the bench, if i switch the front motor to the rear, it spins up normally. that is really weird.
Thank you for your video, it's very detailed. However, I would still need some help. I have an SP Racing F3 with a Racerstar RS20A BLheli_S, and I can make all the motors work fine using Betaflight. The issue arises when I try to use the transmitter, as one of the motors starts spinning very fast, much faster than the other three, making it impossible to control the drone. Any ideas on what might be causing this? Thanks!
@MCsCreations
2 жыл бұрын
Thanks a bunch for all the tips, Joshua! 😊 Stay safe there with your family! 🖖😊
@spionfpv2428
2 жыл бұрын
Super useful video.. My newest drone just did something like this, so now it's time to troubleshoot. Perfect timing for this video :D Many thanks from Denmark.
@TechReview2000
2 жыл бұрын
Thank you for tips. I crashed my very large 10kg drone the other day, the motors are twitching. These tips will help a lot
@gameboys248
2 жыл бұрын
I dont know if you realised, but your XT60 negative wire on the circuit breaker disconnected
@SkyCandyVisuals
2 жыл бұрын
Plot twist drone isn't broken the smoke stopper has been fkn with you the whole time 🥴 19:30 Fpv drone building is a fn worm hole. Is the escs? Is it the motors? Is it too little filtering? Is it a bad gyro, is it this is it that maaaaaaan. Fxxk. I just bought new components and do process of elimination. Replace what I can best identify as the problem and if that doesn't fix it then that part I just removed was still good put it back into the drone or good parts bin and try the next possible culprit. 😉
@jacobreezyfpv6287
2 жыл бұрын
Thank you so much JB I can finally just send people to this video. This is the most common question I get. haven to go back and forth with questions to fix the problem no more. Lol 🤣
@TheSpyFishMan
Жыл бұрын
I've been having an issue with my legacy KISS setup, I've done lots of troubleshooting, and also lot's of part swaps. New motor, new flight controller, new ESC, swapping the wires between the FC and ESC, monitoring Rx link quality, etc. Sometimes I think both of my 4in1 ESCs have the same issue, but then I think it's the flight controller, because both of them exhibit the issue too. The problem seems to be with ESC #4 on the KISS 25A 4in1. No dead shorts exist through the mosfets. in fact the ESC functions fine unless it's accelerating quickly. It can hover, and I can do maneuvers on any axis, but if I jam the sticks, the quad spins out and falls out of the sky, and won't re-arm. Does anyone have experience diagnosing the kiss 25A 4 in 1 or KISS in general?
@nickbrown7700
Жыл бұрын
There is always a point with his amazing videos that I get lost and it's exhausting to keep up. This hobby is wonderful, but taxing at times. Thanks Joshua!
@AyaadhAmeen
10 ай бұрын
Hiii can u reply to my comment pls coz my drone motor is spinning even before I throttle it and it was giving off this burnt smell just before this happened and now it ain't flying 😢 pls tell me what the problem might be
@LowetheTechGuy
Жыл бұрын
Ho ahead and spin em up while holding it down by hand. Jim Bob will hold the J for well until the ambulance arrives to restart your SMOKER. You know the Purple headed yogurt slinger, one eyed snake, weiner, willy or any other hundreds of names. I still will laugh when someone forgets or gets comfy, such as myself. Even after being attacked by my 1st quad, an Eachine Falcon 180, "Ready to Fly". Haha that was a funny joke huh. It was rtf alright straight into my face.
@TechReview2000
2 жыл бұрын
Thank you for tips. I crashed my very large 10kg drone the other day, the motors are twitching. These tips will help a lot
@altermannfliegt3927
2 жыл бұрын
Very good explanation. I wish I would have seen it two years ago when I started with brushless motors and ESC s. I have to learn this lesson by myself. I don't need it before with nitro motors. ;-)
@guschtlweidinger9251
3 ай бұрын
Hey Joshua. First of all, thanks for the great video! I have a problem that kinda fits the video but not exactly. I conected my newly build drone to betaflight an as wanted to test the motors, they didn't spin. When i out the motor throttle up to 1068 they all start twitching. As i out the throttle higher all of the motors stop again. What could cause this problem? Thanks in advance!
@varidzain7468
2 жыл бұрын
Hy josh.... Kindly to help me. My 2,5" get not hard crash. After that my motor number 2 get twitching. I re soldering and opend the motor to clean up. After that motor without props are OK. But when i put it back the prop motor number 2 get twitching again. I removed the props its no problem. How can?? Thanks
@j-pacer4887
Жыл бұрын
So, I don't know what is going on, but I have a tinyhawk III, and one motor is not working properly. The motor doesn't exactly twitch, at least at >3o% throttle, but it doesn't turn quickly or smoothly. I connected to BLHeli and see 4 esc's, I have tried running the CLI dump for the tinyhawk III on betaflight, I have tried bot new and old motors, and I still have the same behavior. The motors all look fine and feel fine, and I have tried moving a working one over and it still doesn't work in that ESC port. I have also tried unplugging all the other motors from the ESC and powering up the quad, and I still hear 5 beeps, So can anyone help me figure out what is wrong?
@highlandsvideo
2 жыл бұрын
What would it mean when the first 3 beeps always happen twice before the last two?
@jimouris
2 жыл бұрын
Awesome video. I have a similar situation with a tinywhoop. I swapped the "faulty" motor and it works fine when I plug it into a different location. So that either points to a short circuit or a bad ESC. How do you go from there?
@petrokemikal
Жыл бұрын
Super annoyed.. built my first quad and ended up soldering the main batt terminals backwards and fried the fc, waited for a new fc to come, finished off the build and now 2 of the motors wont spin up properly.. My luck ive either damaged motors or also fried the esc... Sooo frustrating and a big waste of money.. I tried everything reflashing the esc, reflashing the fc, did several motor spinup tests in betaflight and still the back 2 motors randomly start and stop working.. Dont know where to look now !!
@TheErick211_
23 күн бұрын
any video explaining what to do when esc configurator can't read any of my motors? It was working initially but after some bet a flight changes it stopped reading them
@breakflight
2 жыл бұрын
Joshua Bardwell, You're always calling those MT30. I've only ever heard of them as MR30. What's the story?
@pravyadav5264
Жыл бұрын
Hi, thanks for all the information. I have a Dji avatar and was upgrading to axis flying upgrade kit with new motors, everything went well but at the end the front 2 motors are unresponsive, tried swiping with back one but front still unresponsive, back works fine, any help on this on this please
@BrownSoloFPV
2 жыл бұрын
What if you get the 3 beeps but not the last two on an AIO board? My tiny trainer just fell out of the sky lol I threw a fresh battery on and just got the first 3 beeps and nothing more. It’s the BetaFPV AIO that comes with the tiny trainer DIY kit.
@traviscook5144
2 жыл бұрын
As soon as you said Ken Herron I was immediately turned off. Ive found that guys personality exceedingly annoying. Just my personal opinion though and I’m only some guy on the Internet so… With that being said this is the video we all needed so great job 🤙🏻
@nicks_got_tricks7023
Жыл бұрын
My motor is perfectly fine, the resistence is normal, I get all the beeps and can fly it skakily but its slow and the one motor doesn't beep or anything. When I arm it, it twiches and goes perfectly fine. I can't quite tell if its the motor or esc and I'm kinda new to the hobby. Anyone know?
@coilockerfpv
2 жыл бұрын
Trippy. I just went through this same diagnostic process about an hour ago. It was a bad motor 🤓
@Woodsywoodsy-sj9qy
Жыл бұрын
So I got a motor & esc that both work on a servo/esc tester but not in the model. I can put another esc & same or different motor back in model & all OK. Put the new esc back in & it twitch/click. Any ideas as this video not really help.
@NAQFPV
2 жыл бұрын
Can't wait to see the music video made with the 2:17 worship and2:22 tick tick tick. Awesome video as well
@Az-xi6jt
7 ай бұрын
I use speedybee f7 v3. 1 my motor does not beep.even i change good motor same thing happen.what caused that???.
@Scibble_FPV
Жыл бұрын
So I have a Darwin Baby Ape v2 and I crashed it in a tree and when it crashed the wires got ripped out of the motor, so I bought a new motor, and soldered it on correctly, before I plugged in a battery I checked it with a multimeter to make sure the nodes where not touching (wich non were) then I powered it on. When I armed it the motor that I had replaced started twitching along with the led. I did the test to see if I had a blown mosfet, but I suggested that I didn’t. When I boot up the drone I can feel all the beeps on the motor. I removed the motor and then tried arming it, and the led flickered still, so it is probably not the motor. What do you think I should do?
@pablomoreno1999
4 ай бұрын
what does it mean if out of the last 2 beeps i only get one?? both motors vibrate, and this happens to me 95% of the time, the other 5% it starts everything up normally, driving me nuts
@holgenn
2 жыл бұрын
Check the xt 60 plug from the bad vifly. I had the same issue and found out, that one side was off...
@TheEviling
2 жыл бұрын
17:32 missed opportunity to change T-shirt to "Back to the Bando 2" :)
@CarbonGlassMan
2 жыл бұрын
Now lets trouble shoot the smoke stopper and fix it.
@taimar1000
2 жыл бұрын
My quad makes first 3 beeps twice and then 2 beeps follows, what could be a problem?
@Davflys
7 ай бұрын
Random question. I know this is an older video but the beeps mean the same if you have bluejay and not blheli?
@titogomez2069
Жыл бұрын
One of motors randomly stops working at times mid air then starts working again. Do you know that could be
@frequentlyfascinated
Жыл бұрын
Think it would work with those smokestoppers that fail closed? ;-)
@diehardfpv4166
2 жыл бұрын
Yo JB! What hand screw driver are you using? I definitely need me one of those!
@Marcus2750-u1t
Жыл бұрын
Vertical play in your shaft is always bad……
@Airoflyer_fpv
2 жыл бұрын
Happen to me 3 times with a skyliner spun into air at full speed ,had to jump In. A bush
@koni101
Жыл бұрын
can somebody help pls i have bad motors and when i connect the battery it starts rapidly beeping
@mutoryu
2 жыл бұрын
What if one motor start to twitch when flying? And only this motor becomes very hot
@greatsouthernfpvrc3322
2 жыл бұрын
If had the mamba f405 and f722 fc's die on me a ton of times with is suck a pain
@u250_fpv2
2 жыл бұрын
Do you see any disadvantage in using a charger's power supply feature with the current limit set to 1A compared to using a smoke stopper?
@JoshuaBardwell
2 жыл бұрын
Some power supplies don't like the noisy back voltage from the ESC and can be damaged.
@u250_fpv2
2 жыл бұрын
@@JoshuaBardwell Good point. I still think the risk is low especially when not pulling larger currents and being gentle with motor testing but of course the smoke stopper is cheaper than a charger.
@aliimran5238
8 ай бұрын
when i go full throttle my motor spins but gradually slows down and stops
Пікірлер: 246