Hi Andreas. It was really amazing video. I'll be glad if you do Pixhawk 2.4.8 series and pixhawk 2.4.8 in quadplane. I think it will be trend.
@orientflyer
3 жыл бұрын
Thanks Andreas for your patience in showing your vtol plane setup. Very nice. Can you also explain how the carbon arm motor is fastened under the wing of the aircraft? Thanks again.
@andreasklein5782
3 жыл бұрын
There are two carbon tubes press-fitted into the foam wing. And the motor arm is mounted to those tubes with a 3D printed part
@orientflyer
3 жыл бұрын
Tq again.
@pilotmiami1
2 жыл бұрын
Bravo
@menelaosc.menelaou2508
3 жыл бұрын
Hello Andreas. Very nice video. Can you please give me details of how you setup the servo o/p's in Mission Planner.
@ultimatearistocrat
3 жыл бұрын
Hi Andreas ! It was a relief to find your video on Quadplane on KZitem as there are no other videos for the same. I am trying to build a QuadPlane. Can you please explain which pixhawk outputs are connected to the vertical motors and which was connected to the thrust motor. Also, how do we assign these outputs for motors and servos in mission planner . Thank you
@andreasklein5782
3 жыл бұрын
The quad motor signals are connected to the pins M5, M6, M7 and M8 on the power distribution board. The main motor is in M3. For the mission planner, you have to use the quadplane firmware. It should be set up already with this motor order
@ultimatearistocrat
3 жыл бұрын
Thank you
@sudeeshkaveti6432
Жыл бұрын
Please make a video on how you set that transitions in mission planner
@obniktiv
3 жыл бұрын
Hello, at 16:07 you mention that the signal wires of the Servos should go to the Ports M1-M4 (Motor1 - Motor4). What does your "Servo Output" in Missionplanner look like with this wiring? My quadplane works fine expect for the Servos! All servos have 5V power, as you described in your video and are not defect. So I have to connect the signal wire of my aileron servos to M3 and M4 and my elevator to M2 (no rudder) for example? Thank you in advance! Best Regards, great video!
@ayshaalmaz599
3 жыл бұрын
what is the frame type selected in the mission planner ?
@atashilahiri3372
3 жыл бұрын
Please confirm whether Quad Plane can be possible with APM 2.8 ?
@AdrianCharubin
2 жыл бұрын
Hi Andreas. What battery/batteries are you using? (brand, capacity, discharge rate, etc.)
@manilaboy350
9 ай бұрын
Hi Andreas! Perfect Job! Could you share please what parameters you set up in Full Parameters list? Especially Q_plane's parameters. Thanks a lot!
@user-bn3de4kc4e
2 жыл бұрын
Hello, I'm a student studying drones. I'm going to make a quadplane, but I'm going to make it in the form of a lift and cruise like this video, not a tilting type. But I don't know what command to use when I fly automatically. Can I just use the vtol command? Or do I have to make my own instructions? Thank you for your video.
@asanterichard9498
2 жыл бұрын
Thanks for more vivid explanation, can you help me out select parts for my vtol, thank you.
@laelae1005
Жыл бұрын
I didn't see the way you calibrate the motor? How do you calibrate the motor?
@sinoks2022
3 жыл бұрын
my fixed wing motor is not run in air and it crashed . why it didnt run (fixed wing motor) ? which parameter ı should setting ı have no airspeed sensor
@italogiulianomolettolobos8879
4 жыл бұрын
Andreas, i bother you again: What material are the wings covered with?
@andreasklein5782
4 жыл бұрын
Is packing tape, not the best job. Look it up at Uline.
@italogiulianomolettolobos8879
4 жыл бұрын
Hi Andreas! Thank you very much for the video! I have one question: what is the model of your power distribution board?
@andreasklein5782
3 жыл бұрын
It comes with the pixhawk4
@akkaradechsrithongchai7766
3 жыл бұрын
Cloud you share STL ? Thanks
@aesatishchaudhary5933
3 жыл бұрын
What will the CG of the airplane in Quadplabe setup
@andreasklein5782
3 жыл бұрын
Is designed to stay as the original CG of the plane
@pilotmiami1
2 жыл бұрын
Where to buy parts
@user-me4nf7lj9h
2 жыл бұрын
Hi Andreas please can you share the parameter file for mission planner
Пікірлер: 33