That red thing pushes the lever down im currently working on mine because the gears don’t engage well but that thermo actuator does move
@icanfixitars5610
4 ай бұрын
🤔Got to install a Mode Shifter/ Actuator on a GE Stackable🙄
@mikediles2216
3 ай бұрын
I've changed it 2 times but still grinds can you help me with that situation
@yvettebrown2323
2 ай бұрын
All the videos I find only address the washer. I need help for my dryer that wont start after tripping circuit breaker.
@markwhitman3155
Жыл бұрын
hello, could you please let me know how to access the rear suspension rods on a ge stackable?
@icanfixitars5610
4 ай бұрын
It's a Wax motor... It is activated by 120 vac Which heats the wax then pushes the lever to agitate or spin....Anthony Appliance Specialist here at you're service😁🫡
@lvl88661
2 жыл бұрын
good job
@kwamijw3363
3 жыл бұрын
Hi Matthew. I am at the exact same point you are in this video. Fills Drains but does not agitate or spin. Were you able to get a solution?? Thanks
@kw6713a
2 жыл бұрын
Did you ever solve it friend?
@kwamijw3363
2 жыл бұрын
@@kw6713a no sorry. I exhausted my efforts and ended up selling it.
@kw6713a
2 жыл бұрын
@@kwamijw3363 I'll report on my outcome in case someone else comes through here. In my case a sock fell into the cooling fan beneath the motor, breaking the little clips that held in place the magnet in the cooling fan. The magnet then sucked up to the motor, blocking the speed sensor and stopping the machine from spinning at all. Replacing the cooling fan, about $40 and a half hour of work, fixed the problem.
@preferreddrummer1
4 ай бұрын
@@kw6713a Do you mean the speed sensor is what you repaired? And if so, how was the outcome? Did it fix the problem? My error code says "blocked motor". But nothing actually blocking the motor. It just humms when trying to engage into spin cycle. Eveything else works i.e agitation, rinse, fill etc. Any help is much appreciated! Thanks in advance.
@kw6713a
4 ай бұрын
@@preferreddrummer1 I replaced the entire fan because the clips holding a magnet inside the fan were broken. I suppose it might happen that the clips break from something that impacted them but is no longer in there, like a coin or something that is later ejected, or maybe they just break over time. Once the magnet inside the fan detaches, it will block the speed sensor, and the drum will not spin. In my case I did not have to replace the speed sensor, just remove the magnet that was obstructing it, though I recall reading that the speed sensor can be broken from this magnet impacting it. I can't say whether this would give the motor obstructed code, but seems possible. I've since moved to a different house and don't have that device anymore, so this is the best I can remember. Best of luck.
@Rick-Williams59
Жыл бұрын
Speed sensor is bad
@mastergates83
Жыл бұрын
Where is the speed sensor located? I still have the unit because dryer works fine. Bought a cheap used washer, but if I could get this thing running again that'd be awesome
@ApartmentMaintenance
Жыл бұрын
@@mastergates83 I have a video on my channel replacing the speed sensor on this exact GE stackable washer. Enjoy & share! Thanks 👍 kzitem.info/news/bejne/u5WtumepnnuBnI4
@76089randy
Жыл бұрын
You need to testing the parts I’m a washer an dryer repair guy. That actuator is what moves that clutch up and down. I’m 100 percent sure that’s your problem. May need to jus put it back up there if it don’t work replace it
Пікірлер: 21