Installation looks really good. I can’t wait to see it in action.
@customfabrications
10 ай бұрын
Thanks! Me too…
@jeffpiper7430
4 ай бұрын
thanks u cleared up a few questions before i buy a post , trouble is not having access to a milling machine , only thing i can think of is to take off the slide and take it and the block to a shop ... more $$$$ , my lathe is about the size or maybe a little smaller so the axa sounds like the go
@customfabrications
4 ай бұрын
Thanks for commenting! Glad you found it helpful. Good luck with it.
@keitharciero311
3 ай бұрын
I had the same issue with my gooving tool as well. But I was able to lower the tool holder further by turning the top compound slide. Also it's possible to find someone on ebay mass producing T-nuts. The Southbend 9" inparticular is easy to find one for.
@customfabrications
3 ай бұрын
Cool, thanks for the tip!
@semvergogna
6 ай бұрын
The importance of a friend with a milling machine… 😂
@customfabrications
6 ай бұрын
Sometimes it’s hard to tell if they like you just for your tools…
@150flyer4
10 ай бұрын
I’m so glad you have issues.
@customfabrications
10 ай бұрын
Yup, it’s not just you…
@qwerty125920
9 ай бұрын
When did u Buy that It fits in your garage?
@customfabrications
9 ай бұрын
I bought it used about a year ago. Or two. It’s on a bench in the corner of the garage.
@jimmattingly4234
3 ай бұрын
You won't believe I don't have a mill that I can put on so I did all my cutting of block with a saw
@customfabrications
3 ай бұрын
What ever works!
@jimmattingly4234
3 ай бұрын
I just did mine today and had to make plate fit
@customfabrications
3 ай бұрын
Cool, glad you got it to work.
@jimmattingly4234
3 ай бұрын
Can you tell me what kind of lathe that is I have 1 just like it with no name plates
@customfabrications
3 ай бұрын
It’s a 10in Logan.
@jimmattingly4234
3 ай бұрын
Thank you
@customfabrications
3 ай бұрын
You’re welcome@@jimmattingly4234
@johncolvin2561
5 ай бұрын
The first digit after dash is the size 1= AXA, 2 = BXA, 3 =CXA.
@customfabrications
5 ай бұрын
Thanks
@winandd8649
4 ай бұрын
@@customfabrications And of course 0= 0XA
@customfabrications
4 ай бұрын
Makes perfect sense…@@winandd8649
@johncolvin2561
5 ай бұрын
You needed an AXA toolholder system, not a BXA.
@customfabrications
5 ай бұрын
I was on with fence with that. When I researched sizing, there’s always an overlap. So for my lathe, I was either on the max end of an A, or the small end of a B. Everything I read said that if your lathe size overlaps two tool holder sizes, to use the bigger tool holder. So that’s what I did. Maybe an AXA would fit on the compound better? IDK, so far it’s working ok for me though.
@jimmattingly4234
3 ай бұрын
AXA is what I put on mine works great
@customfabrications
3 ай бұрын
Yea, I had a hard time deciding between AXA or BXA. the size of the lathe is right between the two. Glad to hear yours is working out for you. Thanks for watching and commenting.@@jimmattingly4234
@XPFTP
4 ай бұрын
i thought 250 was AXA ? o boy now iam lost and the point of bigger post if your size overlaps. now iam more cornfused.
@customfabrications
4 ай бұрын
Well they don’t make it easy. I was thoroughly confused while researching all this. And I’m not completely sure I fully get it now. Thanks for watching and commenting!
@winandd8649
4 ай бұрын
Ouch, it's little too big for your lathe 😆
@customfabrications
4 ай бұрын
Not according to everything I read. It’s a 10in lathe, which is on the low end of the one I got (which is for about 8 to 15 in) and the high end of the next size smaller (which is for about 6 to 10in). And everything I read said to go with the bigger one if your lathe overlapped two sizes. So I did what was recommended. I thought I explained that in the video.
Пікірлер: 33