Hey please help me mine is turning on but bringing E1 code what can be the problem
@LatishaBlayne
11 ай бұрын
Hi I'm looking for a 2 inch motor with pin right in the middle so it can rotate a goddess and power a pump for a made in Taiwan oil rain lamp. Any ideas? They are made in 1980's I just need power. It was working today but the wires came off as I restrung the fishing wire for the oil to drip. It hasn't powered on now. I'm so sad and don't know where to find this little motor. I only see one other one on easy. The light goes on but the motor is for the oil to pump and goddess to spin . I don't see any others like it or any information.
@yoshispcelectronicservices
11 ай бұрын
Hi Latisha, Check out this link, it maybe what you are looking for. It has both the pump and motor. rainlampguy.com/products/oilrainlamprepair-pump?gclid=Cj0KCQjw7JOpBhCfARIsAL3bobeyC9QkFvJLDT4wEhvM2ghGJ3VJzWBAZzh-G0ok1JgOIqfKEhwnHx4aAlh4EALw_wcB&variant=45603236675863
@LatishaBlayne
9 ай бұрын
@@yoshispcelectronicservices thank you but I need a pump & motor that also turns the goddess on this one.
@ltk20352
10 ай бұрын
This looks familiar to a bella air fryer pro 90121 series. So basically you have to solder this right?. Not just a connect black fuse type setup as seen in regular air fryers.
@yoshispcelectronicservices
10 ай бұрын
Yes, exactly, this is a delicate solder job but doable. The wire winding is delicate but as long as you take your time, you should be alright. Thank you for the comment.
@peterdao1807
Жыл бұрын
Can you make a short clip on how to open the chefman rj38-10-rdo-v2 air fryer?
@yoshispcelectronicservices
Жыл бұрын
Hi, I have not had that unit in for repairs yet. I had to take the top off of the other unit in my video. There were 6 plastic locking tabs that were difficult to take off. After that was off, the rest was just screws but I am just speculating of the rj38-10-rdo-v2 fryer. The unit I worked on was a chef man dual air with dual side by side trays. Thank you for your comment and if I do get one of these units in, I will do a disassembly video for you.
@davidsimpson4314
Жыл бұрын
How do you remove the tabs?
@liawhitney2202
4 ай бұрын
How do i open it?.
@yoshispcelectronicservices
4 ай бұрын
Hi, the middle top vent opens up and the tabs are really hard to release. Ended up breaking a couple but there is six tabs if I remember. One on the left and right and two on front and back. The screws to disassemble are under that top middle plastic piece. The rest should go smooth after that. Thank you and hope this helps.
@StephenHood-bx5sr
9 ай бұрын
Is there an easy way to solder the replacement part without overheating the new thermal fuse?
@yoshispcelectronicservices
9 ай бұрын
Hi Stephen, The best way, in my opinion, is to wrap the wire around the new leads of the fuse near the end and only leave the soldering iron on the leads and wire until solder flows. Make sure to use flux to make the solder flow better and use low temp solder if concerned. The heat from that shouldn't harm the fuse, if done efficiently. Thank you for the comment.
@lawrencegrace9302
Жыл бұрын
What do you mean "It is open"? How do you fix it please?
@yoshispcelectronicservices
Жыл бұрын
When you test with a multimeter in ohms range, normally should read 0.000 ohms or very close to zero. When it is an open circuit is show 0L which means it is infinite ohms since there is no connection internally when the thermal fuse protects the circuit. To repair you need the number off the thermal fuse. You should be able to source the part locally or online. Then carefully unwrap the wire till you see the solder joints to the wire winding. Unsolder both sides of the thermal fuse. Solder new fuse and wrap up the same way it was before. If you need more help don't hesitate to ask. Thank you.
Пікірлер: 17