I've always been taught that 120 - 125°F is the ideal temperature to set a water heater thermostat, as this temperature range high enough to reduce or eliminate the growth of harmful bacteria that can cause Legionnaires disease, but still low enough so as not to cause immediate scalding although burns can still occur, particularly in children and elderly persons. Higher temperatures also increase energy consumption and reduce the life of the unit. All that being said, households with children, disabled or elderly persons may want to consider a lower temperature setting, in the 110-120 range. If a dishwasher recommends hotter water in the 140°F range for instance, tempering valves should be installed at individual faucets, particularly important for the bathtub/shower, to reduce the maximum temperature delivered. Note that most modern dishwashers are equipped with an internal heater to boost the water temperature as needed, so water heater settings exceeding 125°F are rarely necessary for residential use. On the flipside, some commercial water heaters have thermostats with a maximum setting of 180°F, and a minimum of 120°F.
@internachi
26 күн бұрын
That's really good information. Thank you for sharing.
@KB-ie7jr
5 ай бұрын
Weren't those the dip tubes that you were calling the anode rods inside the tanks?
@internachi
4 ай бұрын
Good question for the inspector at Ray (Arthur) Kline at www.nachi.org/certified-inspectors/arthur-kline-cmi-23150
@robertg6431
3 жыл бұрын
Great video. What brand is the gas leak detector you use in the video? Thanks!
@internachi
3 жыл бұрын
Not sure. You may contact Ray at www.nachi.org/certified-inspectors/arthur-kline-cmi-23150
@DansVlog
Жыл бұрын
Should we mention running the hot water to ensure the CO2 is actually going to detect something? If the hot water tank is full and up to temp, the burner no burning 🔥 The CO2 leak is guaranteed to not be leaking if burner no burning 🔥
@internachi
Жыл бұрын
Correct.
@jf5245
2 жыл бұрын
I bought a new house and they used flex pipes. Also just put it right on top of the wood, no drain pan. Will that pass a home inspection?
@internachi
Жыл бұрын
Yes.
@jf5245
Жыл бұрын
@@internachi I had a plumber come and add a drain pain for $130.00. No issues on the inspection other than changing a few gci plug ins.
@andreilesiuk9538
Жыл бұрын
Hi , I have a natural draft water heater that flues into the brick chimney. Sometimes when I use kitchen or washroom fan my water heater starts back-drafting… would installing a liner into the chimney help to stop backdraft? Do I also need a combustion air intake? Thanks
@internachi
Жыл бұрын
Great tip!
@-.__.__.-Rad
4 ай бұрын
@@internachi I think he was looking for a tip from you
@-.__.__.-Rad
4 ай бұрын
You can open a window if you turn the fans on... It would help with negative pressure at the water heater. Also check the furnace air returns(close them), they can also create negative pressure if they're located in the same room/basement. Basically anything that can create a vacuum will create backdraft. You have the best knowledge of what factors you can control. But next water heater, I would go with a power vent one. It would take care of your backdraft
@andreilesiuk9538
4 ай бұрын
@@-.__.__.-Radthank you!!!
@theletsbehonestatheist6131
3 жыл бұрын
How long can the vent flue run?
@internachi
3 жыл бұрын
Code does put a limit on it.
@queenmonkeyhead
3 жыл бұрын
I found a mistake he did not mention. The gas valve should be install before the union for AWH .
@internachi
3 жыл бұрын
Good catch. Thank you for watching and commenting. More videos are at www.nachi.org/webinars
@FirdayNights
Жыл бұрын
can people use never seize as a gas pipe thread sealent?
@internachi
Жыл бұрын
Okay.
@SerenoOunce
Жыл бұрын
Anti-seize probably OK on a union nut but *never* on the pipe threads. If pipe dope is correctly applied it will serve the same function anyway.
@FirdayNights
Жыл бұрын
you cannot put anything on union. if pipe dope has the same function, why cannot put on pipe threads? @@SerenoOunce
@sandymoonstone855
4 жыл бұрын
ty
@internachi
4 жыл бұрын
You're welcome.
@jerrysweany278
2 жыл бұрын
What about an expansion tank? When is it required?
@internachi
2 жыл бұрын
When it's a closed system.
@mehranpoustizadeh8704
4 жыл бұрын
Thanks very useful
@internachi
4 жыл бұрын
Thank you for watching the video. Glad it was useful.
Пікірлер: 32