If you want a link to every too used, go check out this video in the Trigger Times section of our webpage! Oh also, no I do not like using cup tipped punches for this task, I find that they do not transfer enough energy to do this effectively on the more stubborn pins you sometimes run into.
@robotbuster1487
Жыл бұрын
@@TettyBoyFloyd A gunsmith with a true machinist experience, and a Bridgeport w/Digital Read Out unit, can pick the original 2 pin holes in the barrel. Make note of the locations using the Digital read out. Slide the new FSB into barrel , put it all in a special clamping jig bolted to the Bridgeport table. Drill,then taper ream That's a brief description. I've left out a few steps. Oversized replacement pins may be needed. Some of us remove FSB taper pins with a hydraulic arbor press.
@bradd8383
Жыл бұрын
Can we get a video of the blackout defense barrels
@juniyananajukyu
Жыл бұрын
Caleb, did you have to re-zero your irons afterwards?
@raffieb762
Жыл бұрын
I need to switch out barrels for my sp1, so what you are saying is the barrel has to be drilled? They don't sell barrels pre drilled?
@raffieb762
Жыл бұрын
@Jared Kikeman I don't have the equipment or experience for all that haha, thank you! Big help
@LILJ830
Жыл бұрын
This guy is like the Bob Ross of firearms.
@psycopaintball22
Жыл бұрын
Just beat the devil out of it!
@frankbrowning328
Жыл бұрын
Excellent point on using the large punch. It isn't often you find someone that is not a Gunsmith that knows the proper way to remove a round top tapered pin. I learned this back in Gunsmithing school decades ago and when people 1st see me do it they nearly all ask why I'm starting with the large punch
@SmokinCoyote70
8 ай бұрын
I'm not a gunsmith and I knew that but there's a lot of things I don't know about the AR platform I can field strip it clean it and shoot it . I was in the army but they really don't go into to much detail about the workings of the rifle . I'm a AK guy but I do own an AR and it has a pesty front sight post sticking up that I want to remove lol idk how to do it or what gas block I need or what kind of handguard to install afterwards
@Usicky12
4 ай бұрын
@@SmokinCoyote70 then why did u buy an AR with a front sight post? lol
@shawnparrish1999
Жыл бұрын
More videos like this, please. Good straight forward instruction with years of experience behind it.
@wejones426
Жыл бұрын
Loving the AT-4 in the safe😂
@robdavidson4945
Жыл бұрын
Thanks for the tutorial. The orange bench block makes this faster and easier.
@murphymmc
Жыл бұрын
Great tip. Let's have Brownells develop a punch that has a matched radius concave tip expressly for those pins, like a nail set with an 1/8" tip, but straight shank. That would nearly eliminate any "slippage" off the pin head while impacting. You could get rich, Caleb.😏
@MR619Can
Жыл бұрын
they already have and he mentioned it in his comment = cup tipped punch. he doesn't like to use it. I have used both techniques and for the infrequent armourer who has to do this once every year or 3, the method he showed in the video is the best way. YMMV
@KuntryBoy4Lyfe
Жыл бұрын
Thanks for the video! I have always avoided barrels with fixed front sights like this because I didn't want to mess with them if I decided to go free float. I feel confident I can "knock it out" now if I decide to change it up, lol.
@sluttybutt
Жыл бұрын
Don't feel too confident. Some manufacturers go absolutely apeshit in their assembly process and even veterans have been defeated
@rodgersmith1573
Жыл бұрын
Fixed front sights are becoming less and less common as free float handguards are taking over, as well as the time it takes to actually drill and ream for the taper pins on the A1 and A2 front sight/gas blocks. In other words, if you come across a barrel with one installed, you ought to leave it be, and find a barrel without the aforementioned work done to it for free floating purposes.
@KuntryBoy4Lyfe
Жыл бұрын
@rodger smith Yes, that's true, but the reason I wanted one was simply for the "classic" look. I'm just glad to know I can take it off myself if I decide to put a free float on.
@toddparsons2980
Жыл бұрын
This was exactly the tech tip I needed as I have been wanting to do this but have been reluctant. Thanks.
@TrippUpthemountain
9 ай бұрын
I’ve never seen better instruction on the nuances of the way to hold the punch and finessing the tools any better. Absolutely top shelf instruction. Thank you.
@pole_barn_builder
Жыл бұрын
Caleb, i promise, no hair joke. It would be cool if you did a video on how you got into gunsmithing and some more of your background with guns!
@feez357
Жыл бұрын
What do you mean - no hair joke?!! I would LOVE to have his hair!! I might wash the grease out and trim the sideburns a little but it would be better than my ugly ass bald head.
@jmpetersrn
3 ай бұрын
I just wish I HAD hair. 😢
@aintgonnaworrynomore
Жыл бұрын
Thanks for the tips. Got the front sight bench block yesterday. I was having a devil of a time.
@jamespilbeam209
8 ай бұрын
As usual, Caleb explains and demonstrates in a no-nonsense manner. Thank you!!😊
@gadsdenjim8785
Жыл бұрын
I like using a appropriately sized Nail Set to initially get the pins moving. I got a couple that are the perfect size that hug the rounded tip of the pins. No slipping off. Works good for driving them in too.
@afroghair6793
Жыл бұрын
Thank you Brownells for this psa.
@bobdole234bd
Жыл бұрын
Thanks for taking the mystery out of this process
@pb68slab18
9 ай бұрын
As a toolmaker, I hate taper pins. Most people use a flat punch when the ends are not flat. Using a flat punch on the rounded small end of a taper pin usually flares it out a bit, turning into a rivet!
@lawman5511
4 ай бұрын
Have not done this in 20 years. Great refresher!
@maxwelltodd7757
Жыл бұрын
I use a more solid surface, an anvil, as a base to drive the taper pins in and out. Works better and faster.
@1BXB
Жыл бұрын
As always learning from your right-to-the point videos. Thanks!
@texas66
Жыл бұрын
More mass is most important, in fact you need mass on both sides of the block. If they don't break loose with those baby taps on the bench, get twice the hammer and put it on a bare concrete floor. Make triple sure you're striking the small side and say a short prayer to St. Stoner while you're at it!
@MadChristoph
Ай бұрын
Thanks, I plan on getting an AR-15 with a removable carry handle and fixed sights, I would like shoot with iron sights sometimes but also want to experience with red dot sights
@GregsGruns
Жыл бұрын
Great video, Caleb. I have a slightly different block and I have never had the pins come out as easy as you did there... then again a lot of times I'm messing with crusty milsurp parts. Maybe I need to get one of those blocks...
@wittsullivan8130
Жыл бұрын
One time my son bought an AR Stoner upper receiver from MidwayUSA on sale that was a really nice price. He couldn't get it to zero with irons, in fact, the front sight pin was coming out and it was still shooting high. As it turned out, they installed a standard height front sight tower onto the flat top upper instead of a tower marked with an "F" for flat top. After MidwayUSA customer support told me, "I don't what we can do about it, usually customers just slap a red dot on it and they're happy." My son went to a local shop, bought a correctly "F" marked tower. He had no problems removing the flash hider and front sight tower, but the holes on the new tower wouldn't line up. As it turned out, whoever drilled the slots on the barrel for the taper pins drilled one of them at an angle and then drilled holes to match on the original (incorrect) front sight tower, so no other sight tower would ever fit right using the slots and holes. Evidently the guys at MidwayUSA and AR Stoner don't give a crap, they're just cranking 'em out with the wrong components. I was raised if you're going to do something, do it right. If not for personal pride but to prevent a customer from having problems, which end up as your problems, costing money to fix for no good reason. It's no brainer to see if the front sight tower had "F" on it when you're building a flat top upper and drill it straight. Anyway, the guy at the local shop did unholy things to a rollpin to make it fit the angled slot. It works, but it looks janky. I never received a reply from Mr. Potterfield about it.
@rodgersmith1573
Жыл бұрын
Every A1/A2 pinned front sight block is going to be UNIQUE. The way in which it is drilled then reamed allows for variances between them all. It's considered to be a permanent modification to the barrel and does not need compatibility across all front sight block/gas blocks. Yours is a very special circumstance which should've been handled by customer service and warranty work. I also agree with you that they could have done more to ensure it was an "F" marked front sight block, but since your modification looks so janky, knock out that roll pin and the remaining taper pin, remove the sight block, break free the barrel nut torque, remove the upper receiver, replace with an A2 upper receiver, re-install barrel nut (30-80 FT-LB. torque value), re-install gas block with taper pins, and run some A2 shiny, slim handguards. Install rifle receiver extension and A2 spacer, A2 buttstock, and A2 pistol grip. Voila! Retro rifle! Next, begin assembly of high speed, low drag Gucci rifle using the A3/A4 flattop upper, and begin with a barrel that is not pinned. Unless you want pinned. In which case, get yourself something like an FNMI CAGE code barrel (if you can find it), FN America Cold Hammer Forged barrel, or something of that nature. Stay away from the Stoner shit. Just 'cause it says Stoner doesn't mean Eugene Stoner had anything to do with those parts produced nowadays.
@wittsullivan8130
Жыл бұрын
@@rodgersmith1573 You have to be kidding. You're telling me to upgrade a $200 upper with over $X00 worth of parts? I know "ARStoner" is just a name, just like Armalite, and even Colt rifles aren't the same as they were 30 years (or more) ago. I was banking on MidwayUSA's reputation and they failed me. Any person worth pulling the handle can drill straight, not at a 15% angle and I hope they can see there's no "F" on the part that's matching up to a flat top.
@rodgersmith1573
Жыл бұрын
@@wittsullivan8130 I am SUGGESTING you do the aforementioned upgrades because you've currently got one roll pin which doesn't belong, and the only thing to make it 'look' right would be to return the non F-marked FSB to your barrel, thus giving you a sight meant for a carry handle. That would then leave you with your flat top upper with which you could spend a bit here and a bit there over time until you've got a completed rifle. Or, keep running the roll pin and the 15 degree angle F-marked FSB... It was merely a suggestion.
@flea-kh7om
Жыл бұрын
Yep, same way I've been doing it since 1972. Great job Caleb
@Beanmachine9198
Жыл бұрын
Good stuff as always, from our S. Louisiana man💪💪
@hoosiered471
Жыл бұрын
Great instructional video!!! Thanks!!!
@ianalderson5133
10 ай бұрын
If you're having issues the only answer is a larger punch, a 2-3lbs hand sledge, and a non rebounding surface. Not concrete. Not plastic. Wood or iron backstop
@timothykennedy3434
Ай бұрын
Great instructions! Done by the numbers!
@tangolima6462
Жыл бұрын
Good video, I always soak the pins in AeroKroil before I remove them. I’ve never had to double tape the punch to break them loose. Also the largest Starett punch is good for peening a M1 barrel where the gas tube interferes.
@rodneyobrien4624
Жыл бұрын
Just did mine on the M&P sport 2 and man they were tight!!!! Heated them up a little and it helped, also used a tapered punch…thanks for the video
@harleemannfromtheast
9 күн бұрын
Fantastic video. TY so much. Just what I needed. 👍👍
@janssenmoen953
4 ай бұрын
I like the AT4 in the safe 😅
@johnphillips222
Жыл бұрын
Here are some additional tricks with the taper pins for the FSB. 1) Use an inductive heater to make the FSB pretty warm. That thermally releases the taper pins. 2) Use a tapered, cup tip punch. 3) Place the punch block on a concrete surface or super solid bench to better eliminate the bounce. 4) A 24 or 32 ounce ball peen hammer seems to work best. At work we use an inductive heater and a hydraulic press with a cup tip to do this work. Not everyone can afford that setup.
@TimCleese
20 күн бұрын
Caleb seems like the kind of guy that had a left-side ear ring in high school.
@anon135
Жыл бұрын
always enjoy the vids. Thank you...
@seanrhone5306
Жыл бұрын
I really need a safe with a AT4 as well!
@carloschaparro2413
8 ай бұрын
Bros casually got a rocket launcher chilling in the safe 🇺🇸🦅
@Black5Delta
Жыл бұрын
Great video, Caleb. Maybe I've missed it, but have you done a video on correct gas tube lengths for different barrels or suppressed barrels? Very curious about building my own upper soon.
@mistert51
Жыл бұрын
A couple of months ago I had purchased one of the A1/retro 10.3” barrels from the site to do a “MK18 Mod 0/CQBR Block I at home” build and attempted to remove the FSB to install a Carbine length KAC FF RAS rail and I could not get those pins to budge. After about 30-45 minutes I did manage to get one of them out, but the other didn’t move at all. I ended up admitting defeat and reinstalled the one pin and went with a KAC M4 RAS instead. The FSB now forever bears the marks of my frustration lmao.
@loboloco866
Жыл бұрын
Excellent review, outstanding thanks Caleb.
@wagon9082
Жыл бұрын
Wonderful Video. I would like to learn about drilling the barrel for Gas Block Pins. Online people talk about using vise grips and such. I also have not found a good fixture to fixture this.
@brownells
Жыл бұрын
Caleb has a secret tip he'll share in the near future.
@wagon9082
Жыл бұрын
@@brownells i am very much looking forward to that. :-)
@BenRivered
Жыл бұрын
Awesome, Caleb! You made that look easy bro. Nice video. Thanks.
@davidhalldurham
8 ай бұрын
Thank you, Caleb! Excellent video!
@ETHRON1
Жыл бұрын
I have a specifically cut block of wood I put under the chamber end of the barrel to stabilize it...because it is a pain fighting it...as a rule of thumb, after you get one out the other is a piece of cake...usually.
@danielrobbins5834
Жыл бұрын
I always measure the pin ends first to determine direction of taper. S&W M&P’s sometimes have the pins going in opposite directions.
@tylerbarnes4806
Жыл бұрын
I found out the hard way after I snapped the tip off my punch taking the gas block off my S&W. Make sure to measure first!
@Hero1117a
Жыл бұрын
Excellent
@RonWayneOfficial
Жыл бұрын
Great stuff! Subscribed. 🤠👍
@Beastmaster6actual
Жыл бұрын
Love the AT4 in the safe
@jimhurstjr
4 ай бұрын
Thank you so much for this video😊
@billhatcher2984
Жыл бұрын
Thanks that's a good tidbit I don't work on them much but if I need it I will know thanks again
@LilYeshua
Жыл бұрын
Use a gas block pin punch with the special shaped punch end that keeps the pin from mushrooming and follow Caleb’s instructions and use a solid surface to bang on.
@ETHRON1
Жыл бұрын
I know one you won't get out with a punch...unless they've changed their process.... CMMG, they hydrologically press the pins in and they are not Tapered like normal pins. In case you are wondering, I got that from them. A video I did along time ago I broke 3 punches before I called them. I had to cut the A2 block off or send it to them...
@ryanthorne5432
Жыл бұрын
Kroil, or other good penetrating oil, can help the pins get moving.
@mattfleming86
Жыл бұрын
A gentle blast on the block itself with a propane torch can help too by expanding the metal on the block (you do not want to heat the pins.) It also helps your penetrant creep in a little. It doesn't take much heat to help. I've only dealt with a REALLY stuck pin once. Usually they come out the easy way... but there is always that one.
@sparkyfister
4 ай бұрын
"Eyeballs do not grow back" Sure buddy, believe the government lies! 😂
@johnb3616
Жыл бұрын
So if you chose to put a low profile gas lock on and gas tube do you just cover the holes that were made for the pins or is there something else that needs to be done to ensure the gas block set screws stay in place with those holes….such as using the holes for dimple spots if that makes sense to you?
@James-fs4rn
9 ай бұрын
👍 thanks for sharing. Bet this will save a lot of beat up parts.
@25centsapop
Жыл бұрын
Third time I've subscribed to y'all Thanks for another great video
@glockparaastra
Жыл бұрын
Great demonstration. Thanks!
@skullofserpent5727
Жыл бұрын
Good morning America!
@Justforfun-ek7et
8 ай бұрын
Is that an AT4 hiding in the safe? 😂
@ralphjohnson8775
Жыл бұрын
I ues a 407 3/8 mayhew punch and a 2lb hammer 🔨 With a wack or 2 they will move. Then I use a smaller punch just to push them out by hand.
@alexcasaresOracleAZ
3 ай бұрын
Do you guys have a video showing how to install this type of iron sight onto a brand new barrel that doesn't have the notches?
@hectorperalta8787
9 ай бұрын
Can we talk about the bazooka in the safe lol
@some_cool_random_guy
Жыл бұрын
i love your haircut
@mrouija25
Жыл бұрын
Now i just bought a retro barrel from you guys (brownells) and the front site is very canted to the right side! Now i ordered new pins and was going to try to remove the old pins and straighten the front site block. I tried what your doing and was beating the you know what out of them and they will not budge, and yes im driving them out the right way, do you have any helpful ideas?? Please help! Thanks
@jesusrivera8909
Жыл бұрын
BCM pins are really hard to get out nicely, so I channeled my inner bubba and used a Dremel.
@johng1902
7 ай бұрын
Thank you. 🙂
@Timber_LXG_5
Жыл бұрын
a pinned FSP is my favorite gasblock
@Gbrown0341
6 ай бұрын
First hammer strike is at 5:28 JHC
@mrshort2379
Жыл бұрын
great content great tip: you made that look easy. now all I nee is for you to show me how to fix my trigger reset. when I pull the trigger, and then go to slowly ease off to reset, it fires again, but it only does it when I slowly ease off the trigger to reset. if I just let of the trigger it resets no problem
@navywolf1753
Жыл бұрын
Sounds like a disconnector or disconnector spring issue
@abolishtheatfandrepealthenfa
Жыл бұрын
Good stuff
@brandojaco
Жыл бұрын
My grinder didn't struggle lol. Came right off without any damage.
@GodGunsGills
Жыл бұрын
Facts
@blantant
Жыл бұрын
My grinder worked after many curse words and failed attempts at punching it out. Didn't realize i needed the big punch
@memesarentfunny2248
Жыл бұрын
wtf
@linkbond08
Жыл бұрын
And here I was breaking out the cutting torch.
@skigdividerx4991
9 ай бұрын
Fact: They never come out that easy!!! EVER!
@bunnyoperator
Жыл бұрын
Facts. 🤣 Coincidentally, I recently released a vid on the Centurion Arms CMR cutout handguards that require manipulation of the FSB. I'll link this vid in there for the folks that need it.
@caleblebaron1179
2 ай бұрын
somebody show this to the survivalist in honest hearts.
@caseyfoster710
Жыл бұрын
New Sub here. great vid, thx, it was exactly what I was looking for!
@ChaohsiangChen
Жыл бұрын
It would be nice if Brownells can show us how to assemble a faux dissy barrel.
@happyhome41
Жыл бұрын
FANTASTIC !
@turtledove871
Ай бұрын
Thanks
@actionjksn
Жыл бұрын
I would like to have a jig that would allow me to drill these same holes for a low profile gas block. I think they make something but it's pretty expensive. Basically put it in place with the set screws and then drill the taper holes and pin it. I'll probably never do it but I would like to. I'm sure it's a lot of work and harder than it looks
@killersp1974
Жыл бұрын
Better off to just have a Gunsmith do the job for you; piece of mind is a great thing. Nnothing worse than a sight post that's crooked or the reaming of the 2-0 pins that are too deep and 1 sticks out too far.
@actionjksn
Жыл бұрын
@@killersp1974 What does a low profile gas block have to do with a sight post? I successfully machined an 80% steel frame 1911 with a hand jig I doubt that I need a a gunsmith if I had a jig for this.
@danefoss9679
Жыл бұрын
Great video
@brycetrezise8792
Жыл бұрын
Can you get a LPGB that will fit the pin holes?
@scottmahony4742
10 ай бұрын
Thanks man! Got em!
@rustynail246
Жыл бұрын
Nice job on this one, I mean " this one". Now try the other ones that the pins were pressed through in the factory such as Adams Arms gas block and Olympic Arms.
@pogeegitz
4 ай бұрын
So how do you remove the barrel from the upper/remove the gas tube before taking the had block off???
@Sandshredder2
Жыл бұрын
The mystery has been solved!
@stearnbrown3846
6 ай бұрын
I want to add a free floating hand gaurd. I know I will need to replace Gass block with a low profile one. Any recommendations?
@madmike9398
2 ай бұрын
i hammered out the pins on my lap and installed the tiny roll pin for the gas tube also on my lap. if it gets lost, it gets lost. xD!!!
@Lucysdad66
5 ай бұрын
Out of the whole gun them 2 pins are the hardest thing to do by far.
@jimmywilliamson8540
Жыл бұрын
I had been wondering for a while. I might actually put mine back on. I'm just not a big fan of the four sided Cheese-greater hand guard that came with my low mileage AR.
@SmokinCoyote70
8 ай бұрын
I have a 20in heavy barrel with a front sight post on it . I wonder if I can remove it and install an .936 adjustable gas block on it ? Or do I even need a new gas block ? Is the gas block built into this front sight post ?
@PureCountryof91
Жыл бұрын
This will be important when I build the 6.5 or .243 that I want from a piston gun..
@derek45auto23
Жыл бұрын
Sabre defense pins are backwards....they made really nice barrels
@jacobmoore7650
Жыл бұрын
Awesome, thanks…… is that an AT4 in the safe? Lol.
@sixoffive
Жыл бұрын
brass ball pen hammer, brass punch or steel punch if needed
@4g63attack
Жыл бұрын
Also if you are unsure which is the big side used a calibers to check...
@ezrabrooks12
Жыл бұрын
Good Job!!!!!
@davidschaadt3460
Жыл бұрын
I tried it ,I wanted to replace a slightly rough barrel nut but it wasn't to bad .But without getting to aggressive I gave up .The nut wasn't that bad.
Пікірлер: 221