DO NOT pull the trigger after you rack the slide to to check the chamber to make sure it's unloaded. The internal hammer is in the cocked position and out of the way of the slide when you go to reassemble your Ruger. If you pull the trigger before disassemble, the hammer is in the up or "fired" position and you won't get the slide to go all the way back on. You will have to manually, with your finger, push the hammer back into the cocked position to get it out of the way. I learned this the hard way. Disassembly.....rack the slide, engage the slide "lock" to inspect and insure the pistol is not loaded, release the slide lock....DO NOT PULL THE TRIGGER!!!!!!. As you see here, remove the pin, clean and lub, reinstall the slide..reinstall the pin. If the pin seems to fight back, tilt it down a bit, put a slight bit of pressure down on the end of the pin while pushing it in. Don't pull the trigger. He didn't of course but didn't mention this..leave the pistol cocked.
@edpaskan7012
Жыл бұрын
Thanks for this note. I couldn't reassemble mine and that's why I got you tube!
@chanakasgalindo6229
Жыл бұрын
I still can’t reasemble mine , i did pull the triger and i tried everything and it will not go back please help me
@astroventure2221
Жыл бұрын
@@chanakasgalindo6229I don't know if you got it resolved. When it's disassembled you have to manually cock it and there will be two clicks. Then you can reassemble.
@jackk09
9 ай бұрын
HA HA got on YT to figure out how to reassemble because it would not go back together, this saved me from overreacting, ha ha. THANKS
@farrisdiogenes271
8 ай бұрын
Lmao thanks I already made the mistake 😂😂😂of
@sebastiangraham001
4 жыл бұрын
Great video, clear speaking, simple instructions. Even 3 years later this still helps people out. Good vid
@CryptoMineLLC
3 жыл бұрын
Much appreciated!
@swiftshift3780
2 жыл бұрын
5years later. Still helping out. Thanks!!
@catiloh6086
Ай бұрын
🧑💻
@paulntx
2 жыл бұрын
Keep it short and to the point without annoying music. PERFECT video.
@AngelOrtiz-nu1pl
3 жыл бұрын
Thank you ;You make it so simple . I have my first Ruger 380 and I love it .
@joemostaccioli243
3 жыл бұрын
This is the 3rd and easiest way to dissemble the LCP. Thanks, Guy!!
@CryptoMineLLC
3 жыл бұрын
What are the other ways? I'm always open to learning more!
@sirvilhelmofyonderland
8 ай бұрын
Thanks for the video. Just cleaned mine while watching. I’m an OTR truck driver and carry my .380, it gets abused. Developing rust on exterior. But cleaned it up with oil and metal brush. I love my little.380. I have a Glock 23, but it’s so big and blocky , can’t really conceal it.
@matthewwilliams1709
3 жыл бұрын
Thank you for the video. I was reading about how to disassemble and clean my Ruger LCP but I’m more of a visual learner. This helped me out tremendously.
@guerinquedens9642
Жыл бұрын
Thank you for the step by step. Short and to the point. Bravo Zulu!
@quickhondaz
4 жыл бұрын
Nice, quick and to the point video. Thanks for the insight.
@justaguy4real
3 жыл бұрын
I concur
@jacobduhthrowbak3226
3 жыл бұрын
So simple and helpful, thank you. Love these little LCPs, they're very solid.
@matthewwilliams1709
3 жыл бұрын
I love mine. Just a well built little gun. Racking the slide was difficult on mine until I cleaned and oiled it. Does it a bit easier now.
@daequanshambley1621
2 ай бұрын
Proper gun safety, good explanation, and to the point. Good video
@davidrudolph2825
2 жыл бұрын
This is an excellent video! Short and to the point with good instructions! I just purchased one of these pistols and this has been very helpful indeed! Could not be any better!
@bobwh
Жыл бұрын
Great, quick video. I've been learning to field strip my guns and this one is by far the easiest. Thanks!
@wildestcowboy2668
Жыл бұрын
Where are you located Robert?
@oldcop18
3 жыл бұрын
Good video but I have one observation: You can and should take the recoil spring off the guiderod for cleaning and lubing, they’re designed to come apart. Also, there are two recoil springs, an inner and outer. Gently pull them apart and brush lightly after shooting.
@xPigger
3 жыл бұрын
MY SPRINGS
@MagicPachinko
Жыл бұрын
Forgot how to take the spring loaded pin out. Thanks for your video. Saved me from trying to find my owners manual!
@miriamofsanik981
Жыл бұрын
Clear and concise. Thank you.
@ericstanford7670
7 ай бұрын
Thank you for doing this video it was very helpful. I just purchased one and broke it down and cleaned and oiled it for the first time. Your detailed instructions on putting the pin back in was particularly helpful.
@CryptoMineLLC
7 ай бұрын
Glad it helped! Even I go back and watch this video whenever I have to clean it again.
@maxinerussell6857
4 жыл бұрын
Thank You very straight forward
@renedelavina5869
2 жыл бұрын
Excellent video. Very easy to understand.
@Cmagic678
5 жыл бұрын
My takedown pin was very difficult to remove. You mentioned that you don't have to pull the slide back but in other vids they say to pull back like a 1/4 inch but that seemed to work just fine for you. It didnt seem like pulling the slide back relieved tension on the spring as they claimed. It appears it wont hurt anything by not pushing the slide back..
@shostang
4 жыл бұрын
Very simple instructions. Thank you.
@bernardharvey9836
3 жыл бұрын
This video literally just helped me out with my lcp thanks for the video
@BobSmith-zv9mi
Жыл бұрын
Thanks for the great video. My wife just purchased this gun and your video helped her a lot. Thanks
@Wheres-Wolfie
Жыл бұрын
Thank man! Just got one! Much appreciated
@clowd9931
Жыл бұрын
OH WOW EXTREMELY DETAILED INFO. THANK YOU
@my2cents945
3 жыл бұрын
FYI, that "spring" is actually a spring inside a spring. Yep, two springs. I found out the hard way.
@nickcampbell5118
Жыл бұрын
I can't get the slide back on. The spring is in but the gun won't let me put the slide all the way on
@my2cents945
Жыл бұрын
@@nickcampbell5118 Make sure your spring is seated properly. the rod the spring is on should protrude from the front of the gun just under the barrel. I reinstall the pin before working the slide backward also. Plus the slide moves easily for a short distance back then you need to put some muscle into it to go fully back. Let me know how you make out.
@nickcampbell5118
Жыл бұрын
@@my2cents945 just ended up having to cock the hammer back and it went right back on but thanks man. I'll definitely keep this in mind the next time I clean it.
@my2cents945
Жыл бұрын
@@nickcampbell5118 glad you were able to work it out.
@robbieworrell989
Жыл бұрын
This cleared up me trying to figure out what pistol was missing a spring after cleaning a few!
@stephenkuron6906
3 жыл бұрын
Good no BS video.Thank you.
@charliebravo5612
2 жыл бұрын
I finally broke down and got one of these. Thanks for the vid.
@thisoldbelair
Жыл бұрын
Thank you! Just what i needed! 👍
@wildestcowboy2668
Жыл бұрын
Hey Biscayne did u learn anything?
@jerrywhatsworth3589
9 ай бұрын
awesome , i was having one heck of a time putting the pin in , watched the vedio again , paid attention and shhazzam!!
@vapelounge6110
Жыл бұрын
Thank you, I'm used to field stripping my glocks and recently I've acquired a few smaller guns because everything I have is big full size but I'm just used to mainly glocks and this lil Smith and Wesson shield 40 I got but I recently acquired one of these superrrr tiny lil ruger lcp 380s just because why not? And bc it was on sale brand new at my favorite local gun store I buy all my guns from for the most part and I went browsing a few days ago and the owner John that hooks me up sold kt to me brand new for 180 plus tax and gave me 100 rounds of fmj plinkers and 2 boxes of my fav self defense Hornaday critical defense hallow points along with a extra new OEM magazine for it all for free (ammo and mag) whixh is all basically why I bought suck a tiny gun that barelyyy fits my big ol paws lol... but I like to know my guns before I go shoot them and I always field strip them before I WILL go shoot them and wasn't sure as how to field strip it. This was the firdt video that popped up on how to do so and it was quick and straight to the point and very helpful... I saw a little "upgrade on Amazon for it that replaced the pin you have to pry out its got a slot for a flat head screw driver you just turn counter clockwise and it comes out just a tiny bit once you do so you don't have to put a flathead screw driver up against it and risk ruinin ur slide and scratching it up, it was only 15.99 so I think ima order it now but thanks for this video because I was kind of at a loss as I am used to what I'm used tk which is glocks but thanks for this helpful video that was short sweet simple and straight to the point.. now I can finally run it tomorrow at my range at my house... thank you for taking the time to make this video for guys like me thay don't believe in reading manuals lol.... and is too caught up in their ways on how disassemble other brands of firearms as tbats all they primarily know and own! Thank you
@Azazel777
3 жыл бұрын
I liked how easy he made it should make one on how to clean it
@chanakasgalindo6229
2 жыл бұрын
Wow good video very simple
@Dethflash
2 жыл бұрын
Thank you for this video
@robworkman7495
9 күн бұрын
Awesome video, short and simple, Thanks again
@milliondolladivabritt92
7 ай бұрын
Awesome video, it's short and sweet. Thanks
@CryptoMineLLC
7 ай бұрын
Glad you liked it!
@chadlerch73
3 жыл бұрын
Excellent video and presentation. Thank you!
@lopsidedlobster8869
3 жыл бұрын
Thank you, had to disarm my stepmom. Quick and easy guide
@Ferretsnatcher
3 жыл бұрын
Ah the old disarming of the stepmom. Hate when that happens. Soon it will be mother in laws
@readlorey
2 жыл бұрын
That helped me a lot…looks so easy thanks
@NoNickName1122
Ай бұрын
Great video! 10/10 for disassembly!
@trtcommunity9248
4 жыл бұрын
Very helpful. Thank you!
@TroyVD
3 жыл бұрын
Thanks for this.
@banditthesiberian8156
Жыл бұрын
My guide rod springs come apart to polish them and clean them they definitely come apart just make sure the big spring goes over the little one
@kingtut8381
2 жыл бұрын
GREAT TUTORIAL
@terryf5131
2 жыл бұрын
Excellent..took mine to the range today first time..got it good n dirty...this vid is right to the point...thumbs way up..thanks!!
@bmack2938
3 жыл бұрын
An automotive trim bar works well for removing the pin. Got a set for a few bucks at harbor freight.
@TheTedkorn
2 жыл бұрын
Nice one, thank you.
@CryptoMineLLC
2 жыл бұрын
No problem 👍
@bmack2938
3 жыл бұрын
Use a trim bar to remove the pin. They are made of plastic. Typically it’s a tool used to disassemble car dashboard stuff. Maybe remove a radio or something you don’t want to damage. Trim tools are ridged but still they don’t screw up the finish.
@AtrollLOL4Uu
10 ай бұрын
Cool vid & quick to the point 💯
@tomtimcik4264
2 жыл бұрын
Great video very helpful.
@user-yu4on3kn5u
Жыл бұрын
It still helps after 6 years
@tonyguevara4883
3 жыл бұрын
Awesome video
@trustbanker
4 жыл бұрын
Helped a lot, thanks. One thing, it took me a couple times watching you to see that you pushed up on the lock to keep the slide open. Just got this gun from a relative with no instructions with it or from him. Thanks
@CryptoMineLLC
3 жыл бұрын
I'm sorry I didn't explain that part better.
@irafowlerjr.7492
Жыл бұрын
Thanks, very helpful.
@bmk5155
4 жыл бұрын
Thanks man you been super helpful
@casperburgos1066
3 жыл бұрын
AWESOME Thank you
@Rocknranchman
4 жыл бұрын
Great fast tutorial! Thanks for posting it!
@CryptoMineLLC
3 жыл бұрын
Glad it was helpful!
@bmack2938
3 жыл бұрын
I removed the spring, barrel and it still won’t slide all the way back.
@TannerisSmol97
2 жыл бұрын
Git gud
@bmack2938
2 жыл бұрын
The trigger was preventing me from getting the slide back on the frame.
@218Mike
4 жыл бұрын
Big thanks for sharing your knowledge!
@CryptoMineLLC
3 жыл бұрын
Glad it was helpful!
@jimmywilliamson8540
2 жыл бұрын
It's nice that everything John Brown indeed has lived on in a 1000 different in different, probably more like 50000 different versions. But but oh my goodness every time I take this thing apart I have to remind myself I'm not actually breaking it.
@lynnthain380
3 жыл бұрын
Great job
@markleng67
Жыл бұрын
Thanks! gOOD JOB!
@user-hx5vh9uh2n
2 жыл бұрын
Thanks I just bought a used one off a cop in my town. Since it’s off roster in California
@mikepks
3 жыл бұрын
Thank You for Sharing.
@364pgr
3 жыл бұрын
Thanks, helped alot
@fiermonte83
3 жыл бұрын
Thank you!! 👍🏻
@karimmuhammad2306
Ай бұрын
It did help! Thank you brother
@AZ-Ron
4 ай бұрын
Very helpful!
@seven7seven
2 жыл бұрын
Thanks!
@jerrywhatsworth3589
9 ай бұрын
Thanks gin!!
@Johnnykandela
Ай бұрын
Does this gun need to be greased or what would be the procedure on cleaning! I own one but have no shot it for personal reasons but I guess cause I always have it in my waist the sweat is causing a bit of rust is there a way of fixing please rage me to a video or any advice i appreciate it
@wildestcowboy2668
Жыл бұрын
My slide want stay back and today I pulled the trigger and it didn't shoot once
@gdmofo
Жыл бұрын
Muy bueno gracias
@jdmbraceyourself695
2 жыл бұрын
Thanks
@GladishR
2 жыл бұрын
Does the Ruger 380 LCP ever have two springs?
@richardrogers8254
3 жыл бұрын
That pin is probably designed to be removed with a brass 9mm round rim.
@bmack2938
3 жыл бұрын
My LCP won’t slide all the way back. It falls short maybe 3/8”.
@kylestengl8605
3 жыл бұрын
I had the same issue on mine, something weird with the firing hammer getting in the way. Had to pull the trigger to put it down to slide it over, then pull back after I got it past a point, otherwise if I forced it it still made the firing hammer go down. Hopefully you've figured it out after 2 months!
@madx2r0_22
4 жыл бұрын
When removing my spring. The 2 springs disconnected from the rod, does the rod go through under the barrel upon racking normally or is this a malfunction in my firearm
@garyellis1862
2 жыл бұрын
Thk u
@juanitoaguilera3729
4 жыл бұрын
Thanks bro good info 👍🏼
@CryptoMineLLC
3 жыл бұрын
You bet
@lead5s
2 жыл бұрын
Thank you
@bud2935
4 ай бұрын
Thanks! 👍👍
@DARTHDANSAN
10 ай бұрын
Thanks from the future 😅
@Darth_Adi
2 күн бұрын
Lost my pin. Where can I order another one?
@theoppiesghost
3 жыл бұрын
The follower on this clip works just as well as a screwdriver
@ccross15
8 ай бұрын
Took mine apart. I feel like i re assembled it correctly... but now when I try to chamber a round it isn't smooth and seems jammed a bit and I have to really work to get the slide back and a round chambered...any tips?
@CryptoMineLLC
8 ай бұрын
I would try it again to confirm everything is seated properly and inspect for any gunk that may remain along the slide guides. Confirm the feeding ramp is also looking good.
@MyMotorcycleObsession
2 жыл бұрын
Thanks man!
@user-hx5vh9uh2n
2 жыл бұрын
Anyone used a QuickDraw clip on their .380 though or maybe adding one but think maybe it will be hard to draw and stick to firmly To belt or be too Deeply concealed to get to. Other thing someone told Me was body oils will ruin it if it’s in waist against skin.
@timhallas4275
3 жыл бұрын
What if I want to clean the carbon out of the firing pin bore, and the mag-well?
@TheSpencer0000
3 жыл бұрын
good video. I wish you would have removed the live ammunition from the room.
@calebkencel4018
3 жыл бұрын
Why?
@zarinkai2927
3 жыл бұрын
@@calebkencel4018 he could've shot us through the screen 😆
@stoneblue1795
2 жыл бұрын
It's not a basket of snakes. Or liberals.
@scottbrickey8816
2 жыл бұрын
Are you serious?
@kracksmith4ejm1
3 жыл бұрын
does that pin ever get loose over time and fall out when shooting often or when the time is needed ?
@justaguy4real
3 жыл бұрын
1:25 wonder if there's ever much issue with swapping barrels and gun itself, basically differing serial numbers
@CryptoMineLLC
3 жыл бұрын
I wouldn't think so. But I've never tried it.
@mgtrev7557
2 жыл бұрын
ty 🙏
@spacedaddycereal73
4 жыл бұрын
Had issuses slide pin back in
@charlesromano3573
3 жыл бұрын
I have a live round stuck in chamber slide only moving a little how do I get the live round out
@stevemaslow703
3 жыл бұрын
carefully push it out with a wooden dowel rod or a cleaning rod
@gusolascuaga2666
2 жыл бұрын
I was wondering does your barrel move around slightly up and down
@stoneblue1795
2 жыл бұрын
It will when the action is open, certainly.
@robertw.6753
4 жыл бұрын
Good video! I am having trouble with my newly acquired Ruger. In the final stage of reassembly, I cannot get the pin back in. Any suggestions would be appreciated.
@usmczippoguy7947
4 жыл бұрын
I"m sure you haven't been waiting three months to figure out how to put your gun back together haha. But as you have already figured out it won't go all the way back in without pulling the slide just a tiny bit.
@jlynne.7
4 жыл бұрын
@@usmczippoguy7947 thank you 😁
@rJayisawesome
4 жыл бұрын
I found pushing a little back on the slide (1 finger on the front near the muzzle will do) while pushing it in at a slight downward angle does it.
@wmurray003
3 жыл бұрын
Watch that THUMB!!!
@jessepollard3844
3 жыл бұрын
What causes a round to not feed into the chamber on the LCP?
@CryptoMineLLC
3 жыл бұрын
Try giving the feed ramp a good cleaning and a touch of lubrication. If that doesn't work, try different ammo or magazine. Lastly, take it to a local gun smith because beyond that I am not sure.
@stoneblue1795
2 жыл бұрын
Polish the feed ramp with some "Flitz" or similar polish till it looks like chrome. Small dremel cone shaped cotton "buds"- Amazon sells some generic ones that are fine.
Пікірлер: 183