I had a successful maiden flight today thanks to these videos! Much appreciated and looking forward to the next video on PID tuning.
@RCVideoReviews
Ай бұрын
Nice! Glad to hear the videos are helping you guys get in the air with Rotorflight and Nexus.
@nfavor
Ай бұрын
YGE, Scorpion and HWv5 ESC programming through RF will be very nice!!!
@RCVideoReviews
Ай бұрын
Agreed!
@woofie7520
Ай бұрын
Great information guys. Thanks for the effort you boys are putting into this project.
@RCVideoReviews
Ай бұрын
Thanks for watching!
@MrLaban74
14 күн бұрын
Tack!
@RCVideoReviews
14 күн бұрын
Du är välkommen, och tack för att du slog i tipsburken.
@Daniel-qr2cy
Ай бұрын
Thank you so much for your detailed videos. I had a great time setting up my Nexus and a very succesfull maiden ( 6 flights already) with no issues.. Soo looking forward to the next video regarding PID's and learning new things. I still need to get my Autorotation setup for my Kraken 580 using your setup, but will get there.. 10% throttle seems a little low for me but that might just be because I am not a fan of auto's hahahaha..
@RCVideoReviews
Ай бұрын
This is the kind of comment that makes the work worth the effort. I'm glad the videos helped you work through your setup. My Kraken is waiting for its Nexus :)
@blooskyy7
Ай бұрын
Thanks for this excellent series, some great info.Interested to know if you will be also covering PID tuning?
@RCVideoReviews
Ай бұрын
PID tuning will be in Part 5.
@bobwatson6558
3 күн бұрын
Can you use a castle creation esc with nexus. What is the setting for that.
@8da11en
Ай бұрын
Thanks for these videos! Would be great to see an example of a "Normal" throttle mode, like you get on OMP hobby M2 with omp protocol rx; looking at docs, do you create a profile with passthrough governor?
@RCVideoReviews
Ай бұрын
Covered in part 2. Radiomaster Nexus Part 2 • EdgeTX Setup • FREE NEXUS GIVEAWAY! kzitem.infokS20_eaAP8A?feature=share
@ra_Amon
Ай бұрын
One question....if you are going to configure the governor in rotorflight (mode 1), you must deactivate all the ESC governor options, correct? Including soft start? Thank you in advance
@johnoseman572
Ай бұрын
Following up on an earlier question, I am using the Hobbywing Platinum V4 and it comes pre-configured in 'Elf Governor ' mode. Do I need to change the default ESC configuration in any way, or does Rotorflight effectively bypass what the ESC would normally do? Fantastic videos as always! 👍
@RCVideoReviews
Ай бұрын
You want the ESC in fixed wing mode.
@johnoseman572
Ай бұрын
@@RCVideoReviews Thank-you!
@arism.
10 күн бұрын
Hello, or heli linear??
@paul_bunyan
Ай бұрын
Again, great tutorial. I’m still not able to arm after watching this several times. Using a SAB Goblin 280 (havoc) 60A ESC. This ESC has no rpm or telemetry as far as I can tell. Only the ESC signal wire plugged into the ESC spot on the Nexus. I can get the motor to spool up under Motor override. However it will not spool up until 0% throttle pwm value is set to 1350. I’m baffled, I cannot for the life of me get the motor to spool up even after setting up my TX16s like yours (video 2). Is the RPM and telemetry wire required for this to work? Also dumbfounded why the motor won’t spool up at 1033. I have to move the slider half way for it to jump on when set to 1033. I’ll rewatch the tutorials and go at it again. I’m sure I’m missing something. Thanks again for the great support you offer to the hobby.
@RCVideoReviews
Ай бұрын
Did you calibrate the ESC?
@fc1133
Ай бұрын
"This video is part four of a five part series on setting up the brand new Radiomaster Nexus FBL" Hmm? I was going to get this controller but after reading this, I think I am going to pass. : )
@RCVideoReviews
Ай бұрын
Yeah, you definitely should pass.
@fc1133
Ай бұрын
@@RCVideoReviews Not the response I expected, ha ha. I was thinking you going to say something like, "It's not that hard. give it a try."
Пікірлер: 26