Cut off the curved end brass coming out of radiator leave straight section then use a elbow shaped hose with one clamp on each end
@stevemazz3121
4 ай бұрын
He said it was cast iron coming out of the radiator.
@walterbooth534
4 ай бұрын
That would work.
@PeterDowd-r9b
4 ай бұрын
Makes perfect sense to me
@randymellquist2868
4 ай бұрын
💯
@alanluckman7120
4 ай бұрын
Why make it so hard. Cut off the elbow on the radiator and put a hose on it done.
@michaelwalsh98
4 ай бұрын
Having a Radiator Shop change the Elbow to a straight inlet, and go through the radiator so its clean and has no over heating issues would be the right way to fix it.
@bobhalstead1879
4 ай бұрын
Chad is clueless concerning mechanical issues.
@screamnmonkee
4 ай бұрын
If there a rad shop near by have them install a short straight outlet.? That radiator should be gone through anyway.
@tonypiercy9771
4 ай бұрын
First of all you don’t really have the right hoses and you should let Nate take care of it.
@davidcrawford5711
4 ай бұрын
Go away !
@CathySalmon-vw3vs
4 ай бұрын
Some grinding will take care of that. Lol
@FNGstationtwentyeigh
4 ай бұрын
Reminds me of the three stooges as plumbers...
@roypowell3450
4 ай бұрын
Nate will cut the bend off the bottom pipe of the rad so it is straight and then add flexi hose with two clamps..
@1primetech
4 ай бұрын
That air lock should do wonders for the cooling............🥵🥵
@tonymosca6591
4 ай бұрын
No worries if Nate is on it.
@leftyoverton4347
4 ай бұрын
Nate will get a good laugh when he sees that I’m sure.
@PeterDowd-r9b
4 ай бұрын
Nate will sort out this issue for sure with shop hoses and clamps
@aaronbartlett3573
4 ай бұрын
Chad you make soldering so difficult. You used enough solder to do that project about 4 times. Heat each joint individually and heat at the end of the pipe that is inside elbow. It will then pull the solder into the elbow. As soon as your done keep heat on and wipe your joints and pipe with a wet rag. This will wipe all your excess solder off plus remove all the flux so it won't turn green.
@jimderksen1653
4 ай бұрын
Its painful to watch.
@peterrimmington7100
4 ай бұрын
Capillary action.
@michaelleabeter
4 ай бұрын
Cut the outlet on the rad and reangle it
@nickross2423
4 ай бұрын
I think he said he thought it was cast.. really tough to weld
@alpeach9480
4 ай бұрын
@@nickross2423 No need to weld it, just cut it to change the angle.
@nickross2423
4 ай бұрын
@@alpeach9480 maybe I didn't pay attention.. which part are u cutting?
@manuelweber2127
4 ай бұрын
With that loop on the bottom hose there may be a flow/airlock problem...just have to see
@duconce
4 ай бұрын
Just when I thought Chad couldn't raise the dumb meter any higher he came through again. That radiator will most certainly need a core, plus those old radiators were not pressurized. He doesn't know how to solder, the hits keep on coming. Using a 36 rearend and brakes is looking for disaster.Better to just park it over in the big building next all rest of cars you can drive or aren't finnished
@MichaelMeyers-c1e
4 ай бұрын
Let Nate do it !
@Pwandlina
4 ай бұрын
I think Nate's still wiring the dash😅
@briandavis3907
4 ай бұрын
Need to put a bead roll on those copper 90 about an inch up so your hose clamp won’t slide off when under pressure.
@mattjanzen86
4 ай бұрын
As you have stated many times... you learn through mistakes, as long as they don't damage something too "Bad Chad". Also, as you have stated many times... this is not a "how to" channel, it is a "this is what you're doing", including learning, as you do. Keep up the great camera work Jolene! Chadles, Dougles, and Nate'ls, keep on rising to the challenges! It is mighty fine stuff you all do!
@rosswood5147
4 ай бұрын
Spend 6k on another car, but I won't buy anything for the Hudson but rather play with used rad hoses, lol
@bobullrich8137
4 ай бұрын
Yup I know what you mean
@markyaz901
4 ай бұрын
You and Bob boyfriend and girlfriend??
@LorieStull-mg2go
4 ай бұрын
And this is triggering you why?
@nsidor1234
4 ай бұрын
Cobbling stuff together IS & has always been part of Hot Rodding. All of us started in a place where we used what we had because we didn't have the luxury of ordering new...👍🏁
@kevinbarnes5799
4 ай бұрын
this is what happens when making money from doing u tube videos becomes more important than the content that is in the video.
@GeraldBoone-qy2yt
4 ай бұрын
That small block will overheat with that old radiator. I’m sure it’s partially blocked from many years of use.
@Steven-pz3ck
4 ай бұрын
I hope Chad reads these comments. Seems like cutting the lower radiator fitting and using a shorter hose to the pump would be cleaner.
@brentwalkerwalker4474
4 ай бұрын
Some videos are just painful to watch
@avonnova7982
4 ай бұрын
Holy smokes Chad's working off a table never thought I'd see the day
@TommyJensen-pl8qz
4 ай бұрын
Jeg troede først han var alvorlig syg 😂
@howardmarshall5713
4 ай бұрын
Chad when you are soldering those joints together on the copper pipes. If you hold your torch at the point where the pipe starts to narrow then warm the pipe all the way around the solder will get drawn into the joint and flow all the way around leaving a clean joint no drips no leaks. copper is hot enough when the flame of the torch starts to turn green at the centre of the flame. 🙂 👍✌
@joeblow5381
4 ай бұрын
😂
@raymegehee7922
4 ай бұрын
Wait for Nate!!!
@JTTTTx
4 ай бұрын
One last plumbing comment- you may have to add a heating system vent to the top of your copper 90 arrangement . It may circulate, but it also may air lock when you fill it up against a closed thermostat.
@raystackon5113
4 ай бұрын
I've built a copper still or two in my day, watching Chad solder was a thing to behold. Now, I've never welded anything in my life, so I imagine some people who do would get quite a giggle if I tried. He "still" gits er done, though. Good job, Mr. Chad
@maxaita9127
4 ай бұрын
Is it not possible to cut the angle out of the rad outlet and leave it straight and join it withe a 45° hose to water pump?
@norbertrausch9664
4 ай бұрын
Hi to you all !!! Looks like your fan is going to hit your hoses and the radiator. Probably because the radiator mounts r for the original engine and not the engine your putting in now. Going to have to make new mounting points for the radiator. Hopefully your modification works , double clamp your joints Chad. You all have a great day !!!
@ScottStiller
4 ай бұрын
This was painful to watch.
@henryhoie2584
4 ай бұрын
You seem to be making a mountain out of a mole hill chad
@lloydfriend1060
4 ай бұрын
Please let Nate handle the mechanical.😊
@dannico58
4 ай бұрын
OMG it's hard to watch someone solder a copper fitting while holding the heat in the wrong spot, heat the fitting evenly, NOT the pipe
@simpleplumbinganddrainage2745
4 ай бұрын
Absolutely painful to watch
@hotrodsales
4 ай бұрын
Piece of cake..curved hose on one end to fit the pump and straight on the other..cut the radiator fitting straight..you can handle something that simple..
@grantscrimgeour1848
4 ай бұрын
I am sure Nathan could have come up with a better solution to solve the radiator hose problem - because it seems to me the fan blade(s) should have been installed on the front of the water pump first before sorting out the hoses. Others have commented there is the danger of an airlock being formed with the way the hoses are oriented.....time will tell.
@rjfry8979
4 ай бұрын
If that is the cars orginial radiator, the car will overheat in hot weather, quit being so cheap and get a 4 core custom rad built, yes it will be expensive. You have lots of money Jolene driving a new Corvette, so spend some on the build!
@shake-the-earth1
4 ай бұрын
Chad, good job. When you have a will you can make a way to have things work. It may not be pretty but functional. You can buy flex braided stainless steel radiator hoses for cars. Very similar to flex exhaust pipe. Thanks for the video Jolene.
@bondseye66
4 ай бұрын
brother you are a creative genius but in the work of the body, not of the mechanics of thingsmaybe , Nate seems to have a knack for that, you will be able to make more usable cars, Im currently watching and yeah,this one is amusing me, Im curious to see whatere ay get with this. I need that oldie but a goodie neet streeter in my life, rock on!
@bondseye66
4 ай бұрын
@@martyc5466 I was watching that radiator hose mess, and yeah, i thinkI lost a few brain cells, I dont build to that extent, but i can also work on em
@fonhollohan2908
4 ай бұрын
When your soldering, your suppose to heat up the flange area of the elbows and that draws the solder into the seams of the pipe.when you do it that way you able to solder things up very quickly. also you can tact a flat piece of metal to the end of those bolts so that it doesn't grind against the end of the bolts.
@HaywoodJabloowme
4 ай бұрын
Next he will make it from the cheesy chrome molding , hockey tape and undercoat
@James-qr6rp
4 ай бұрын
I wouldn't put that pipe on that nice looking motor
@garrykellogg3585
4 ай бұрын
Cut the curve off the radiator and attach it to the water pump small amount of hose for the final hookup
@kajuncourier
4 ай бұрын
The paint that is on the radiator has to be the same type you would put on a BBQ pit or fire pit. Regular metal paint is not rated for extreme heat sources.
@stephengorham2195
4 ай бұрын
Motor paint header paint marine heat paint exhaust paint..the list is long
@amrelbadawi1
4 ай бұрын
100 degrees Celsius is not extreme
@kajuncourier
4 ай бұрын
Awesome, I know that,thanks for the education for people who don't know that !
@CalChrestensen
4 ай бұрын
This is the most unreal thinking ever , i am sure Nate will take that mess apart and do i right . Do you ever listen to anyone ?
@tonypiercy9771
4 ай бұрын
Need to watch for the fan blade hit the hoses
@DavidSmith-zv7oq
4 ай бұрын
There's no room for a fan behind the radiator, even if there was it's to low to cool, he'll need to go with a electric fan in front of the radiator
@michaelnieman6218
4 ай бұрын
And you think he well spend that money for an electric fan @@DavidSmith-zv7oq
@RichardPearson-jo6hw
4 ай бұрын
No room for a fan
@SMoore-js6fy
4 ай бұрын
I would have built it all out of copper with 2 slip joints. Keep the copper polished!! glad to see your back on the Hudson. Are your going to rebuild the terra Plane engine? It would have a good value for some one do a restore!?!~~
@JTTTTx
4 ай бұрын
Use radiator paint-- it does exist. It is specifically made for that application.
@wmleuschen3586
4 ай бұрын
That would cost money.
@HermanCramer-bp4ls
4 ай бұрын
Let Nate fix it
@garyfoster4555
4 ай бұрын
That may create an air lock in the lower hose..
@terrierich4370
4 ай бұрын
Don't make this complicated, trim the bottom radiator flange . Add a flexible hose, 2 clamps and you're done.
@RaySantamouro
4 ай бұрын
MICKEY MOUSE LET NATE DO IT GEEEZ
@toddbartels2866
4 ай бұрын
Just put in a different radiator.
@bobsobota9797
4 ай бұрын
Hoses just laying out in the open and Chad happened to wonder by staged
@shaggy1958
4 ай бұрын
Cut off the lower radiator outlet and put a straight one on. Simple 90 degree hose and you are done. Easy peasy. Why put ugly …… never mind. Duct tape, bailing wire, and other hick fixes will allow you to keep working on this car for years. Think of this comment when you overheat and lose $20 in antifreeze.
@DarrelAnderson-cv7wp
4 ай бұрын
Chad, You are going to have a cooling issue with that lower hose routing. I would have a radiator shop replace the elbow with a straight nipple. A hose with one elbow and 2 clamps would make it look nice and function like it should. It will be a nice build when done.
@mikethompson9015
4 ай бұрын
Please GOD , someone buy chad a radiator hose .
@lumberdan4659
4 ай бұрын
Need to put a raised shoulder on the fittings or hose will blow/slide off
@lumberdan4659
4 ай бұрын
Please Chad ignore the trolls. We love the content and maybe sometimes we may see something that you should do or we might say oh no, that's not gonna work! Lol Doesn't matter your doing it your way and that's what matters and that's why we watch. Ignore the haters. If it were me I would start flagging them and if they continue I would get rid of them. I for one don't want to read that crap. Makes me feel bad for you guys. Keep it up brother, love the show
@clivejmellis1232
4 ай бұрын
LET NATHAN DO HIS MAGIC ! 😇
@richardnelson7098
4 ай бұрын
Cady take a break 😎✌️
@lawrencerinaldo9635
4 ай бұрын
Ya know to make that copper thing you made look decent, plumbers when sweating pipes, get the joint hot then use a damp cloth used to wipe the area and it looks very professional.
@jesusdelgado3936
4 ай бұрын
Never in my life have I seen anyone used a grinder to a copper soldered piece. Smh
@patrickgilhooly8340
4 ай бұрын
Ms. Jolene- please just call Nathan, he will fix connection from radiator to water pump on 39. I am worried about Chad’s state, this is second time. Please, please get Nathan involved. Please start doing what all shops do, Photograph cars as you take them apart. So easy when you go to put them together again.
@PeterDowd-r9b
4 ай бұрын
Chad and Jolene , In a previous video , I observed that there were 2 new radiators laying against the wall , One of them probably was used in the 1950 Ford is the other being utilized in the 1940 Hot Wheels Replica ? if You and Jolene and Nate have done a great job on the engine swap in the 1936 Hudson Terra Plane. Wouldn't it be practical to acquire another aftermarket radiator and an electric fan back up to complete the project. I wonder what Nate thinks on this issue ?
@MarkJones-qn1eg
4 ай бұрын
You need to heat the elbow back in the bend. Therefore it will pull the solder back into the fitting. Equal amounts of solder. For instance a 1 inch fitting should take no more than 1 inch solder.
@RickyPinkston
4 ай бұрын
A muffler exhaust bender shop would have what's needed probably in the scrap piles you may could get give to you BAD CHAD FREE who knows you don,t want any flow restrictions on that ol girl she will overheat and blow those head gaskets for certain get er did
@GeraldBoone-qy2yt
4 ай бұрын
That’s at least 50 times more solder than you need.
@EugeneGoga
4 ай бұрын
Leave it to Chad to try & rig up a Rube Goldberg device to solve the problem!
@chadshelton6060
4 ай бұрын
Hard to watch for sure.. what a mess. Hope Nate fixes it correctly.
@TokerX
4 ай бұрын
That was the most unnecessary thing I ever seen lol
@robetwolfe3843
4 ай бұрын
Mickey Mouse job, I am disappointed. Any competent radiator shop could modify that outlet or just get a different radiator. The old one should have been cored to make sure it can handle the high volume/pressure of the new engine.
@nevillemills9517
4 ай бұрын
Use a round loop hose put one end on the w/pump and loop it to go on the radiator. Like a big ring of hose O. May have trouble with an air lock. But you could place a valve or tap to disperse the air in it. Just a thought Chad.
@stormy683
4 ай бұрын
Step away and let nathan figure it out. You have no clue
@StevenPalomares
4 ай бұрын
I kind of agree with R I don't think you should skimp on the radiator you have a beautiful powerful motor spend the cash buy a hot rod radiator that way you can cruise to California and back !
@GeraldBoone-qy2yt
4 ай бұрын
Geez. Measure where you want it and take to radiator shop. DONE
@richardnelson7098
4 ай бұрын
Cheap caddy wasted time and resources
@neilwalsh9637
4 ай бұрын
Even a flex rad hose would be better, at least for awhile. Those old hoses look like they’re going to need replaced in about a month…..
@PeterDowd-r9b
4 ай бұрын
When your want to have a proper rate of flow of coolant from the radiator to the automatic transmission . . You don't want create 2 many sharp angles for debris to collect in . When the coolant is under heated pressure. If your going to drive the car on short trips . There's less chance of it overheating. Also the degree level thermostat you use has a n impact on the potential of overheating and causing transmission problems . I would also install a heavy duty transmission cooler on the car as well. I'm sure Chad and Jolene will consult with Nate on the final analysis. on this issue
@junie1955
4 ай бұрын
Just change bottom outlet.cut it and flair end easy hose line up then/ it will never work correct just wrong radiator period.
@r.cogburn816
4 ай бұрын
A few comments about soldering technique, hose applications and how helpful Nate is, otherwise another great day. Good job Jolene. I really like this show, I watch it every damn day.
@keithhumphries8007
4 ай бұрын
Cut the elbow on the rad and notch the opening all around. reduce the opening and braise it. Use a very short piece as a 90 degree hose.
@bobsobota9797
4 ай бұрын
Why not just put new ones on it instead of doing it twice
@merrie59
4 ай бұрын
This is rediculas!! Just go to your local parts store and get the right ( Already curved) hose.
@robastore9192
4 ай бұрын
Take the front engine mounts off ,use the stock side mounts . The radiator is going to be problem its not going to cool the small block, its honey comb not meant for that heat load and the water pump will push far more coolant through it than it can handle its solder with lead wont last . Get four core mustang and fit it to the support . Good luck . Like your show.
@DouglasWiles
4 ай бұрын
I know you are just putting that on temporary right?
@NickDanger1957
4 ай бұрын
Great show today very productive and informative learned a lot !
@beerstein7137
4 ай бұрын
You should heat the outer flange and let the heat draw the solder into the joint
@johnprice58
4 ай бұрын
Mapp gas gets hotter than propane too.
@ignaferreira3213
4 ай бұрын
Jolene help him please
@johnmacmillan2766
4 ай бұрын
Rooster where you at? Nice to see Chad using what he’s got and making it happen! Ya guys he “could’ve “ done it differently but he didn’t he done it his way and bet ya it works just fine. Cheers guys
@robertrabhudsonhornet5869
4 ай бұрын
All i now is Chad is making it all more harder than it needs to be for one and with all them beens it's going to restrict the flow most likely run Hot or over heat and before doing all of that you should have had the fan on the water pump so you would know what your trying to do will fit an not hitting the fan and your favorite thing you like to say you don't like to waste time. Well if you know how to solder you know he's not doing it right lol
@timmiller260
4 ай бұрын
Cut 90 off radiator and it need 2. 5inch hose make turn
@edwardconnor6353
4 ай бұрын
Like having a carpenter fill in for a plumber..no no no Chad take to a radiator shop and have them fix the Neck, or Let Nate do it..
@Knightryder628
4 ай бұрын
Happy Tuesday Bad Chad Nation we live for Bad.
@MaximumDogHerder
4 ай бұрын
Not a good look on an otherwise nice engine. Let Nate do it. To go to all that expense and then cheap out on a radiator is poor judgement in my opinion.
@karmafarbus160
4 ай бұрын
Pure comedy,
@johnvonderhaar677
4 ай бұрын
Cut the elbow off of the radiator right at the bend and put a hose on it with a bend going to the water pump and then straight into the so cut the elbow turn off the elbow cut it off straight so you got to straight nipple coming out of the radiator then put a radiator hose with a curved the curve up at the water pump and going down straight into the
@kevinbarrett9615
4 ай бұрын
This is more like a how not to video !
@johnsabo2376
4 ай бұрын
It ok to cool it I water. Maybe a wet rag. Never seen soldering like this before. If u keep heating it and adding more to it the first solder runs out.
@danieldivertie
4 ай бұрын
Once again not thinking he got rooster to clean the radiator down why did he not get him to paint it before putting it in place and he also should have gotten Nathan to fit it just my opinion not that it makes any difference as he does not listen to what we are saying
@danieldivertie
4 ай бұрын
@@Welder-y5x yes that may be so but it should have been painted before in went back in and it did not matter who paints it It could have been done prior to going back in that is only my opinion you can like it or not up to you
@walterbooth534
4 ай бұрын
The water pump needs to be able to pump coolant without restriction. The angles of the hose may cause flow problems.
@ropesauce
4 ай бұрын
Change the outlet on the rad
@ROBByJONEs-2
4 ай бұрын
let Nathan fix the radiator bottom hose, it looks ugly to say the least
@markkibbey4026
4 ай бұрын
For the note when you soldier you can take a wet rag and just wipe off the excess solder when hot to make it nice and smooth..and look nice..just a note for yah a something to try..
@JTTTTx
4 ай бұрын
Plumber here-- try an 1 1/2 copper DWVstreet 45 clamped to the rubber sleeve on the motor
Пікірлер: 435