Brilliant video extremely helpful, couldn’t find anything anywhere else, thank you very much! 🎉
@mlc4x433
Ай бұрын
Thanks 👍
@alexandraava3034
8 ай бұрын
👍👍
@daviesbikeable
2 жыл бұрын
how come you didn’t plug the diagnostic machine in to set the active anti roll bar valve control block to an open state? this allows it to bleed through the valve block so you can fully change the fluid?
@mlc4x433
2 жыл бұрын
Because I don't have a diagnostic for the newer Range Rover
@Mohammed-zu8sc
Ай бұрын
what kind of oil do we have to use ?
@mlc4x433
Ай бұрын
I used direct from landrover. Basically it's atf but not red
@gerryr1893
Ай бұрын
Neglect
@mlc4x433
Ай бұрын
full main dealer history. not neglect
@TerryUrquhart-v4w
10 ай бұрын
Excellent series of videos on this topic ….love the approach , techniques and real mechanics tricks and solutions…real skills in action … Subscribed …! Well done ..!
@mlc4x433
10 ай бұрын
Thankyou, I'm glad that you enjoyed them and got some help from them
@lukefillingham634
4 ай бұрын
Is that the front sway bar on a l405
@mlc4x433
4 ай бұрын
We did put a new front bar on and replaced the pipes to the rear
@lukefillingham634
4 ай бұрын
@mlc4x433 nice one there only this vid I've found onit everyone's been telling me it's body off job for front ace bar mines got a tapping nocking noise on b roads on motorway it dont make a sound mine weaps oil but someone's says its ok and to just change d bushes and drop links for it
@mlc4x433
4 ай бұрын
I would disconnect chassis links then you can move the arb to see if it clunk's. If it doesn't it should be fine unless it leaks a lot. if links are shot they want changing first to see as they are a little bit cheaper
@300zx-jdmjdm8
Жыл бұрын
I need to bleed my ace by any chance you have some pictures how to make the tool you make to bleed it..
@mlc4x433
Жыл бұрын
I don't have any pictures, but I used an eezi bleed and a thin bit of inner tube to seal it to resevoir with a hole in middle. I then filled an inner tube to 8 psi and connected it to the eezibleed. This pressurises the system. Then you turn ignition on and off while you bleed it. Hope this helps
@mahmudjunayed2332
Жыл бұрын
Where is your garage?
@mlc4x433
Жыл бұрын
We are just outside Corby
@samnelson2840
2 жыл бұрын
Nasty colour on that oil!
@mlc4x433
2 жыл бұрын
Better once it was bled
@misaelacosta1116
2 жыл бұрын
How come you're replacing that part?
@mlc4x433
2 жыл бұрын
pipework was corroded through and starting to weep
@misaelacosta1116
2 жыл бұрын
@@mlc4x433 if that Stabilizer bar goes bad can it make a clunking noise when going over a bump?
@mlc4x433
2 жыл бұрын
if it is clunking it is more than likely ball joints or link arms. It is possible it is the cause more likely the other parts
@BigJ0hn_steez
Жыл бұрын
@@mlc4x433 what if there’s a squeaking noise when making sharp turns or turns in general?
@mlc4x433
Жыл бұрын
it is probably the belt needing replaced
@garydsouza2335
Жыл бұрын
Hi i am getting a funning noise when turning right first this in the morning it worse, I've been told to change the dynamic reservoir under the bonnet and top up the fluid, can this be the cause of the noise, 2014 RRS 3.0LRT SDV6. It sounds like rear most of the time then someone said front..
@mlc4x433
Жыл бұрын
It's not really much information to go on. What speed when turning, how sharp. What type of noise, knocking, grinding? Not sure what chasing the resevoir would do unless they mean pump and resevoir.
@apprentcepat
Жыл бұрын
Really should have chosen a better day to video this job he wind noise wastes the whole video
@mlc4x433
Жыл бұрын
I would love to have chosen the day but I was on holiday from work to do the job and we had huge storms at the same time.
Пікірлер: 32