The white covering on the bracket that is mentioned in the video is just plastic. Make sure to peel it off. Also, if you're looking for this exhaust on Amazon it tends to go out of stock quite a bit. There are two alternatives that look the same. Although, I WON'T guarantee they are the exact same as the Ransoto/Anodizing version. This is the link to the actual Ransoto/ Anodizing exhaust - amzn.to/3fkJbe8 If that's out of stock try this...amzn.to/3DH5s4n Or this...amzn.to/3RzVcAR
@FoamSquatch
2 жыл бұрын
I like how you went back through the different sounds again. Sounds good with the baffle in, but man, without it...... that takes the cake.
@MotoRider2
2 жыл бұрын
Definitely. I really enjoy how it sounds
@iUnloadMags
4 жыл бұрын
Really well done video dude, I appreciate the quality 👌
@MotoRider2
4 жыл бұрын
Thank you. I'm glad you like it.
@asaprocko9108
3 жыл бұрын
facts
@MultiElement21
Жыл бұрын
My neighbours gonna love this exhaust
@JustAMindlessDrone
2 ай бұрын
I've run this exhaust for almost 5 years. 100% tune your bike with power commander or a flash if you plan on keeping your bike for many years. The baffle needs to be out to get the HP gains. It's actually quite alot with the snorkel off. Very noticeable in the top/mid end, didn't notice any low down gains. The exhaust has started to rust. Also the exhaust isn't properly aimed away from the bike so soot builds on swing arm and spool on that side. I actually took the exhaust off last summer and put the breadbox stock exhaust back on and remapped for it. Though going to put it back on today as I don't tour much anymore. Sound does get annoying after 3-4 hours on the highway. Before you try to remove the exhaust nuts on an older bike might want to warm up the exhaust first or soak in a penetrating oil of some sort a day or two before. Last time I did the job the whole stud came out of the head and all the nuts have started to corrode over the years. I went thru ali express instead of just paying for re-seller on amazon. Saved quite alot but obviously take longer for shipping. Valuewise this is quite a deal but keep in mind running this pipe long term untuned long term will probably cause some damage. It was overheating alot sitting in traffic, also bike got very noticeably slower with tons of decel popping while untuned as well. If I ever would do this again, I'd get the flashing kit and go with a better exhaust like Akrapovic. Flashing kit gives you so many more options other then just fuel mapping like fan cut in/cut off, amount of engine braking, etc. Or just get the MT-09.
@MotoRider2
2 ай бұрын
This is a great overview. Thanks for sharing. I agree that there should be some sort of tune. Whether you use a power commander or send it out to be tuned would be good. Mine is still in great shape after all these years. But I also wipe mine down after every ride. And yes, it's loud. After a few hours, it can get annoying, even with ear plugs.
@kxcrunner7
3 жыл бұрын
Got mine today! We’ll definitely be using this to help with the install!
@MotoRider2
3 жыл бұрын
Awesome. You'll love the sound once it's installed.
@syruslife
2 жыл бұрын
i kno the vid is 2 years old but mine just came today. I hope you eventually realized the white around the bracket is actually just a protective sticker for the chrome. apologies if its already been mentioned in the comments. thanks for the vid :)
@MotoRider2
2 жыл бұрын
Yep. Realized it as soon as the video was uploaded. Enjoy the exhaust.
@RoamWithAli
3 жыл бұрын
Thank you so much brother, its one of the best video of installation on KZitem. I have been looking for that Universal Joint Set but didn’t know which one was the right one. So thank you for putting the links in the description.
@MotoRider2
3 жыл бұрын
You're welcome. Glad it was helpful.
@WIRCinc
3 жыл бұрын
Thank you sir. Just finished. Sounds pretty good. For less than 200, you cant beat that with a stick.
@MotoRider2
3 жыл бұрын
Awesome. Enjoy it.
@ultra727
2 жыл бұрын
Thank God I came across this video, I'm getting an R7 when they come out in Australia in 2 weeks. This will save me so much $$ 😄
@MotoRider2
2 жыл бұрын
Awesome. Glad it was helpful
@noahphelan2182
6 ай бұрын
Thank you for the video. It was super helpful for the install.
@erock639
5 ай бұрын
Glad it was helpful.
@boyanlu7927
2 жыл бұрын
the holder bracket has a white protect film on it, you can just peel it off so it will become chrome, it is not painted white
@MotoRider2
2 жыл бұрын
Yep. thanks for the heads up. I realized that as the video was uploading and I placed a note about that in the description
@trruplayaa01
4 жыл бұрын
Good video man. I bought the same thing and that white thing on the clamp your talking about is just a plastic cover. Take it off and it will match with stainless look 👌
@MotoRider2
4 жыл бұрын
Thanks. I realized right after uploading the video about the white plastic cover. Took it off and it all looks good now.
@Ghostsoulless
Жыл бұрын
If anyone has this and wants a bit more noise without the unrefined sound of no db killer at all, you can take the end cap off the db killer. Gives a nice middle ground that’s loud but not obnoxious like no db killer is (imo). Think it has the best exhaust note this way
@mouradchibane1818
4 жыл бұрын
Awesome detailed video!!! Perfect, thanks a lot!!
@MotoRider2
4 жыл бұрын
Thanks
@avertaze6604
3 жыл бұрын
This helped immensely when installing on my 2019. Now my wife doesn't make fun of me driving something that sounds like a moped anymore!
@MotoRider2
3 жыл бұрын
Yeah. The angry sewing machine sound had to go lol
@harminder87
3 жыл бұрын
I just installed the exhaust today ur video was great help man!! Appreciate The bike sounds really dope when rev matching!!
@MotoRider2
3 жыл бұрын
Awesome. Definitely sounds way better than stock. That's for sure.
@blank.e4327
3 жыл бұрын
Without baffle its sound much good
@MotoRider2
3 жыл бұрын
Yes it does.
@AR-3618
3 жыл бұрын
Great instructional video. Just got mine in the mail today, cant wait!
@MotoRider2
3 жыл бұрын
Thanks. Enjoy it.
@SkiPump
4 жыл бұрын
Awesome video. Gonna order this exhaust soon for my 2020. I appreciate how easy this video is to follow!
@MotoRider2
4 жыл бұрын
Thanks. Glad it was helpful. It always frustrated me when "how-to" videos skip steps. So I wanted to make sure this didn't do that.
@SkiPump
4 жыл бұрын
@Yugo RC I just installed it over the weekend and got my ECU back from 2WDW today. Gonna try it out tomorrow!
@petesmall4360
4 жыл бұрын
thank you far making this video. helped make it an easy install.
@MotoRider2
4 жыл бұрын
Sure thing. I'm glad it was helpful
@addyedward6632
3 жыл бұрын
Just did this step by step with your video. Many many many thanks!
@MotoRider2
3 жыл бұрын
You're very, very welcome
@nimashali9076
3 жыл бұрын
For best performance, i highly recommend that you MAP ur ECU. Also change the Air filter to DNA. You will lose power by just changing the exhaust, i did a full remap and the bike was much more responsive.
@MotoRider2
3 жыл бұрын
Yeah. I'm no tech pro so flashing the ECU was the best bet for me. The snorkel was removed from the filter and runs really well this way.
@jericmillarez941
3 жыл бұрын
Nice video bro, about the white paint on the bracket, it’s actually just a wrap cover you need to peel off, i did that to mine.
@MotoRider2
3 жыл бұрын
Thanks. I noticed it was a plastic wrap right after uploading the video. Haha, ended up adding a note in the description after that.
@vikingplisken6241
3 жыл бұрын
Great video helped alot after i have just installed one and it sounds like an absolute beast with this i didnt take off the db killer but its probably even better :D
@MotoRider2
3 жыл бұрын
Yeah. Has a deeper sound without the db killer. And of course, it's louder lol
@REBRIDGES1212
3 жыл бұрын
Nice video! Just put mine on today that white on the strap should peal right off I did on mine it’s just a protective coating
@MotoRider2
3 жыл бұрын
Thanks. I realized that right after uploading the video. Peeled it off, and then left a note in the description mentioning that.
@sharkrape
4 жыл бұрын
Super well put together video dude. 10/10
@MotoRider2
4 жыл бұрын
Thanks. Much appreciated
@rogervalkenburg9328
3 жыл бұрын
Great video and helped immensely when I installed one on my 700 Tracer, thanks.
@MotoRider2
3 жыл бұрын
Thanks. How's it looking and sounding on the Tracer?
@rogervalkenburg9328
3 жыл бұрын
MotoRider The exhaust sounds great; a great deep throated burble at idle & slow to medium acceleration, a real growl when the throttle is opened up. A little popping in the low gears on deceleration, quite normal I’m told and not harmful to the engine by my local Yamaha dealer. Having the ‘noise’ when accelerating actually makes gear changing easier & smoother; great going through the mountains😀
@MotoRider2
3 жыл бұрын
@@rogervalkenburg9328 - Awesome. if you get it tuned the "popping" will go away and the bike will actually pull a bit harder in the mid rang.
@fantazykory
4 жыл бұрын
You suppose to peel that white protective layer off. Lol🤪🤪
@MotoRider2
4 жыл бұрын
Hahaha. Found that out later. Too late to change the video now lol!!!
@justinwilkerson4697
3 жыл бұрын
Sounds good!
@MotoRider2
3 жыл бұрын
Thanks
@lemello18
2 жыл бұрын
@motorider the exhaust holder white part peels off to chrome under it.
@MotoRider2
2 жыл бұрын
Yep. Figured that out after the video was uploaded. There's a note about it in the description for others as well so they realize that.
@hbfilms357
4 жыл бұрын
Good video man. Well done, I have the same exhaust on my bike
@MotoRider2
4 жыл бұрын
Thanks man. How's it been holding up for you?
@hbfilms357
4 жыл бұрын
So far so good!
@AICD1999
4 жыл бұрын
The clamp is silver. That white is a protective over and comes off easily
@MotoRider2
4 жыл бұрын
Yep. I realized the moment I uploaded the video and let everyone know in the description.
@j.m.b3987
2 жыл бұрын
Appreciate your video thank you 👍🏾
@MotoRider2
2 жыл бұрын
My pleasure!
@Mr2mellow
4 жыл бұрын
Hey that white stuff is supposed to come off you got a nice chrome finish under there!
@MotoRider2
4 жыл бұрын
Yep. Realized that right after the video was recorded and posted. So I made a note about that in the description. Thanks
@mr2goulart-mineiro113
3 жыл бұрын
Very detailed video, thanks for posting. 👍 subscribed
@MotoRider2
3 жыл бұрын
Sure thing.
@fernandoperez2513
3 жыл бұрын
Excelente descripción. Gracias!
@MotoRider2
3 жыл бұрын
De nada.
@stefanplayngo5430
2 жыл бұрын
Bro I hope you realized that that is white protective film over the muffler bracket and you had to peal it off :) Otherwise a very well detailed video
@MotoRider2
2 жыл бұрын
Yeah. As soon as the video was uploaded I realized that. Even posted an update about it in the description when the video was uploaded.
@louvega8414
3 жыл бұрын
Great vid, thanks!
@MotoRider2
3 жыл бұрын
Glad you liked it!
@jimwilson9613
3 жыл бұрын
Nice video. This helped me today when I installed mine. Did you notice any difference once you had the tune?
@MotoRider2
3 жыл бұрын
Yes. No popping when accelerating. And it seems the mid range seems to pull a little harder.
@dakotabingham13
4 жыл бұрын
So I have this same exhaust , and I have a power commander fc , any recommendations on what tune I should be used ? Got the bike with this set up and want to make sure it’s running properly .
@MotoRider2
4 жыл бұрын
No idea. I'll be sending the ecu out to be flashed.
@normfry2187
3 жыл бұрын
Hey, I’m getting a 2018 with this setup this week and wondering if you have any feedback on how it’s running or if you got it tuned. I wanna make sure my new bike is running properly. Thanks
@antwonboonk3540
2 жыл бұрын
What power commander tune would I upload for this exhaust?
@MotoRider2
2 жыл бұрын
Not sure. I had it sent out to 2 wheel dyno works to have the ECU flashed. That worked great!!
@crazyman4207
3 жыл бұрын
Where did you find gasket sealant that goes above 1000 degrees? Only copper gasket sealant i have found goes up to 700
@MotoRider2
3 жыл бұрын
I didn't. I just used the one in the video. I've had no problems with it up to this point. If there is a leak from the sealant wearing off, I'll just apply more of what I used.
@crazyman4207
3 жыл бұрын
Bro🤣. That white out is a sticker to protect the chrome. Its silver underneath
@MotoRider2
3 жыл бұрын
Yep, realized that after the video was shot. I immediately left a note about that in the description section when the video was loaded.
@Robocoppat
2 жыл бұрын
What what's the final verdict as far as performance goes? Did you keep the db's out or put them in? It really sounds healthy. I just got a brand new 07. Looking forward to doing some work to it. I'm on the East coast as well. 👍😃
@MotoRider2
2 жыл бұрын
I did a follow up video a year later that goes into all of that. Here's the link... kzitem.info/news/bejne/xG6dr5ylbZ2mhqQ And congrats on the new 07. You'll enjoy it.
@blastedup1953
2 жыл бұрын
Did you lose any low end power from the slip on ?
@MotoRider2
2 жыл бұрын
Before the flash it may have felt slightly less "powerful" but not much. Oh, and this is a full exhaust, not a slip-on.
@kingpinestudios
3 жыл бұрын
How can i pick one of these up? Seems to have been taken down
@MotoRider2
3 жыл бұрын
Yeah. With the craziness of the past year sometimes they're available and sometimes they're not. I'm guessing it's supply chain issues. Hopefully, they'll have some more soon. You'll probably have to keep checking to see if Amazon has them.
@antoniosimental8978
9 ай бұрын
Only one gasket came off (the one on the right). I tried putting the new gaskets on both sides but it would not fit with the gasket on the left. Am i tripping or is that how it is?
@MotoRider2
8 ай бұрын
Both gaskets should come off. It could just be the gasket is stuck in there. You may have to get a tool in there to pull it out. Also, the pipes could be a little wider than the slots so they don't fit perfectly. A little muscle to push them closer together will help them fit. I had to do that slightly.
@antoniosimental8978
8 ай бұрын
Also, it did not come with some pieces that you received but we made it work. Appreciate it!
@MotoRider2
8 ай бұрын
@@antoniosimental8978 - Glad you got it to work out. I've heard that sometimes it doesn't come with everything.
@JAYJAY1787
3 жыл бұрын
I've been seeing with the baffle in you won't need a tune , that baffle out sounds overwhelming but nice but still to much
@MotoRider2
3 жыл бұрын
It's definitely better with a tune for sure. Baffle out is loud, but I wear ear plugs so it doesn't bother me at all.
@jwro1296
2 жыл бұрын
Hi MotoRider, I purchased this exhaust after seeing your video. Question, Should i most def get it flashed before taking it out for a ride or can the flash wait? One more question, do you have the baffle in now or did you end up leaving it out? Thanks for the time!
@MotoRider2
2 жыл бұрын
I rode it a few times before getting flashed. There was definitely a loss in power and it would backfire with and without the db killer. So for me I didn't want to deal with that so I got it flashed right away. I'm not a mechanic so I couldn't tell you if not flashing it will hurt anything in the long run. All I can say is that the flash made a world of difference.
@jwro1296
2 жыл бұрын
@@MotoRider2 Thanks!
@mrh8409
2 жыл бұрын
How do you remove the baffle besides taken the bolt out of the front?
@MotoRider2
2 жыл бұрын
There's a bolt right on the back tip (bottom) of the exhaust that comes right out. Super easy
@kurajek33
3 жыл бұрын
Do you get some cartificate with it, i need to know cause if it don't contains any of that in europe i cant homologate it. PLS i need help.
@MotoRider2
3 жыл бұрын
Don't know what certificate you're talking about. Didn't get anything like that. It does come with a "db killer" which reduces the decibels though
@eastcoastpikachu
3 жыл бұрын
I havent installed my exhaust yet but notice in the baffle there is a cap you can unscrew does yours have the same if so have you tryed it with out the cap baffle installed?
@MotoRider2
3 жыл бұрын
Yep. If you watch until the end of the video you'll see what it sounds like with and without that cap (db killer). I run it without the db killer.
@lukegreeley1056
4 жыл бұрын
Hey man, did you have a metal reducer piece in the muffler that you needed to take out before attaching to the headers? Mine does, wondering how you got it out
@MotoRider2
4 жыл бұрын
Nope. I didn't have anything like that. The muffler slid right on to the pipes.
@uncletorr
4 жыл бұрын
Like Cody c said well put together vid. Did you reflash your ecm after. If not how does it run. People are back and forth about it and I almost don’t want to lose the engine braking. I’m used to it
@MotoRider2
4 жыл бұрын
Thanks. The ecu was flashed by 2 wheel dyno works. I liked the engine braking and was worried about it being eliminated with the tune. But the engine braking didn't go away after the tune. It just made it a bit smoother when letting off the throttle. Not that real jerky motion. As for how it runs, it runs great. No backfiring, and it pulls better in the mid-range.
@uncletorr
4 жыл бұрын
MotoRider My buddy was saying “2WDW” doesn’t do the flash for the 2020 mt07. Obviously they do I’ll look into it. Thanks for the reply ☝️
@josealbertoguzmansantoya1882
4 жыл бұрын
Good video bro. when you put a full system exhaust you must tune the bike or is it not necessary?
@MotoRider2
4 жыл бұрын
I'm no pro so I couldn't answer that for sure. Some people say no, some say yes. I look at it this way, if the bike is programmed to run a stock exhaust then it's not programmed for this exhaust. So I'll be tuning it.
@josealbertoguzmansantoya1882
4 жыл бұрын
MotoRider thank you!!!. How do you fell the bike now? More power ? Less power? or the same like before and just change the sound?
@MotoRider2
4 жыл бұрын
@@josealbertoguzmansantoya1882 - Just installed the exhaust the other day and haven't ridden it much yet. I'll know how it feels when I take it out for a good ride. It definitely sounds WAY better though. It's really loud with the baffle out.
@josealbertoguzmansantoya1882
4 жыл бұрын
MotoRider perfect bro, you have to do other video riding with the new exhaust and tell us how do you fell the bike 👍🏻. I got a MT 07 too and I want to put the same exhaust 😍
@jdonfireofficialmusic5037
2 жыл бұрын
Will it need a tune up?
@MotoRider2
2 жыл бұрын
I'd recommend getting the ECU flashed. It will run much better with it
@DeXx_The_Reaper
Жыл бұрын
Sounds better with Db killer
@deivydasindriulis6229
4 жыл бұрын
Hello just found your video, thank you for tutorial, wanna ask maybe you know did is fit 2020 yamaha mt07 model?? Thanks
@MotoRider2
4 жыл бұрын
Yeah, it should fit.
@REBRIDGES1212
3 жыл бұрын
Fits for sure just put on mine!
@NES-6-25
3 жыл бұрын
Do you still have your bike? What’s the year review of the exhaust?
@MotoRider2
3 жыл бұрын
Yep. Just posted that exact video...kzitem.info/news/bejne/xG6dr5ylbZ2mhqQ
@kkush82
3 жыл бұрын
How has this exhaust held up so far. Mine will be here this saturday. Won't get a tune for it until a month later. Will this hurt the bike. I use it daily to commute to work. Tia
@MotoRider2
3 жыл бұрын
It's held up great so far. I'll be doing a review on how it's held up soon. As for not having it flashed I couldn't tell you if it will hurt the bike. There are a lot of people who haven't. But in my opinion, a flash is worth it and it's not that expensive. It wakes the bike up and just runs better.
@MotoRider2
3 жыл бұрын
Just posted the 1-year review of this exhaust - kzitem.info/news/bejne/xG6dr5ylbZ2mhqQ
@DaniWhiteMoto
4 жыл бұрын
What's the one month consensus? Looking at the same company for my FZ-09..
@MotoRider2
4 жыл бұрын
Very happy with it. Definitely worth getting a tune for it.
@Mononoken
4 жыл бұрын
Very pro video here. What ECU map did you use?
@MotoRider2
4 жыл бұрын
I send the ecu to 2 wheel dyno works. Had it back to me within a week. Runs great with their tune.
@DL-sy5fv
3 жыл бұрын
@@MotoRider2 what map did they use?
@bertobubba
3 жыл бұрын
Nice joob dude
@MotoRider2
3 жыл бұрын
Thanks
@sethhartman8804
4 жыл бұрын
Someone on Amazon said it's leaving discoloration on the swing arm, is this true?
@sethhartman8804
4 жыл бұрын
Okay thanks man
@MotoRider2
4 жыл бұрын
I'd heard of that as well and was concerned when purchasing it. But so far I don't see anything. I've checked to see how hot the swing arm gets because the exhaust points at it a bit and it only gets "warm." I also just make sure to wipe down after riding. But so far, so good.
@brovayurbee6102
3 жыл бұрын
Do you need a tune after this process?
@MotoRider2
3 жыл бұрын
I'm no mechanic so I couldn't say if you "need" a tune. But I had it done and it makes a big difference in how the bike performs. And it's not that expensive so I'd say give it a go. Check out the review video on the exhaust you'll hear a bit more about this.
@brovayurbee6102
3 жыл бұрын
@@MotoRider2 will do, thanks.
@miguelcarongaboury1991
3 жыл бұрын
How we remove the baffle?
@MotoRider2
3 жыл бұрын
There's a screw on the bottom that you just unscrew.
@miguelcarongaboury1991
3 жыл бұрын
@@MotoRider2 ok thanks and nice video
@michaelogg1254
3 жыл бұрын
That’s an Amazon exhaust
@MotoRider2
3 жыл бұрын
That's one of the places you can get it
@BriceTooNice
2 жыл бұрын
mine rubs the swingarm
@MotoRider2
2 жыл бұрын
You should be able to bend it just a bit to reposition it
@BriceTooNice
2 жыл бұрын
@@MotoRider2 i tried but it was getting sketchy lol. I just got some layers of some heat resistance tape where its rubbing at for now
@Miguel-ng5wm
4 жыл бұрын
Mine don't match the headers wtf. I will have to bend them. And yeah it's the correct model.
@MotoRider2
4 жыл бұрын
Yeah. I've heard that happening here and there. In fact I made the mistake of testing to see how they fit before putting the new gaskets in. Hahaha, that was a mistake. I got them in pretty easily but couldn't get them out. Took a lot of muscle but was able to get it eventually.
@mooiboyace
3 жыл бұрын
These Chinese mufflers for the MT07 sound horrible
@MotoRider2
3 жыл бұрын
To each their own I guess. I'm pretty happy with mine
Пікірлер: 158