As far as I’ve seen in other videos and articles, the command “vcgencmd measure_temp” does not just measure gpu. It measures the CPU/GPU (SOC Chip).
@MrMesospheric
5 жыл бұрын
Excellent, no-fuss video. Great temperature control results. Fans are great when operating at home, but in the field, where power is limited, something else is needed.
@squalazzo
5 жыл бұрын
finally someone which knows basic linux commands and use it correctly, not like the many which did temperature testing in last month continuing to press cursor up and enter to repeat last command...
@thomassutrina7469
5 жыл бұрын
The orientation of the board , the heat sinks make a significant effect for natural cooling. You need to create a chimney effect to cause the heat to increase air flow. Orientate the heat sinks so the channels are vertical and place a duct to direct the air. Simplest is a flat card just off the ends of the heat since at about half to the width of the channels. Nothing on the sides. As you make the duct more complex like add sides and extend the duct above the heat sink the air flow will further increase since hot air is less dense then cooler air.
@randywatson8347
4 жыл бұрын
Like the low profile of this cooler. Definitely use it for my custom crampy enclosure.
@PST101
4 жыл бұрын
Thank you. Very clear and very helpful. Did this today.
@dariantel
5 жыл бұрын
excellent video as usual, i prefer passive cooling with no noice at all (i took a heatsink that is like 5x5x7 cm and put on haha, but it would have been fun to know how much noice the pimoroni fan make.
@si12volt1
4 жыл бұрын
running my 4B on a GeeekPi Raspberry Pi 4 Case with ICE Tower Cooler @ 27 deg C with a 4020 fan @ idle very happy
@21bindiya
4 жыл бұрын
amazing video
@stcstwwlove
4 жыл бұрын
I see your heatsink installation in a different place than suggested. others have said largest heatsink on the CPU, memory module (medium), smallest on the USB controller. why did you choose the power supply?
@samuelsantos5559
4 жыл бұрын
Awesome video, tx
@ZainKhanAbdul
Жыл бұрын
The second CPU command doesn’t work - it states “no such file or Diretory” - using ras pi 4 - 8gb model
@mibrahim4245
4 жыл бұрын
Very informative, though you need to read about hysteresis error 😂
@no5x937
5 жыл бұрын
Great video! What is the cfm rating on the Pimoroni fan?
@SamHartmannCom
Жыл бұрын
2:13 doesn't work for me - maybe only on Ras PI OS but not on ubuntu desktop - right?
@ThomasSmoke
5 жыл бұрын
You are overusing the sudo command a bit at the beginning. The only needed was this one used wit apt-get
@docox27
4 жыл бұрын
Great shirt
@anthomore4269
5 жыл бұрын
What about those little cases with heatsink and fan?
@antoniomanuelfidalgo7565
5 жыл бұрын
Great Video.....tks ... great idea
@Duewester
5 жыл бұрын
I just use the temp on the task bar.
@frits183
5 жыл бұрын
How ?
@Duewester
5 жыл бұрын
@@frits183 First off, I'm not a Linux programmer, when a gui is available I use it. Secind, I just monitor - not graphing or making a table. In Raspbian - Right click the menu bar - select panel preferences - select panel applets - select add - find Temperature Monitor and select it - select add - move it to where you want it.
@frits183
5 жыл бұрын
that is great you just explained a simpel way to do it.
@Duewester
5 жыл бұрын
@@frits183 Thank you.
@gebhardscherrer9086
4 ай бұрын
have you tried replacing the stock heatpads with 1.5mm thernal pads from gelid solutions?
@Pngwolffman
5 жыл бұрын
You know what's better than a fan shim? A heat sink *with a fan!
@squalazzo
5 жыл бұрын
no, in various youtube tests resulted that there's no real advantage, the fan is enough
@Pngwolffman
5 жыл бұрын
@@squalazzo try overclocking it to 2GHZ and see if it still isn't thermal throttling. Also if it's under the thermal threshold, sure you won't see any performance improvement but running it hot even though would decrease the life of the cpu, potentially causing it to fail later.
@johnbowman7980
5 жыл бұрын
@@Pngwolffman I have overclocked my Pi 4 to 2GHz. I'm using a cheap pi-fan with no heat sinks for cooling. The temps never get close to the throttle point. Heat sinks are not necessary on a fan cooled Pi 4.
@ProductionsExoTic
4 жыл бұрын
I would like to see you meassure the room temperature as well, and maybe test at different room temperatures
@garygrobard4095
5 жыл бұрын
Thanks as always. Thoughts on the official POE HAT being able to do the cooling?
@CrosstalkSolutions
5 жыл бұрын
It should be comparable, but I didn’t test it.
@sbstn1317
5 жыл бұрын
@@CrosstalkSolutions I use the Raspberry Pi 4 with PoE Hat, but without the noisy Sunon fan. I created my own case for 30 / 40mm fans. With a 30mm 5v "Pi Fan" without heat sink, I end up with the stress test at 60.0'C. I hope I could help you a bit. Here is the link to my modified case, which can be printed via 3d printer. www.thingiverse.com/thing:3724434
@reesericdotci
5 жыл бұрын
why don't you just use cockpit?
@howtoinvest4yourself241
2 жыл бұрын
what would be the temp distribution with the Heat sink and an enclosed case with a fan mounted to the Case?
@Alex-un5tl
5 жыл бұрын
Hi, is it comparable with the official poe hat?
@bbmak0
3 жыл бұрын
mine is 68C degree when i am running 1 youtube video on firefox. Not sure this is normal?
@rednecktech9485
5 жыл бұрын
I've been trying to get a raid NAS working and struggling. I am going headless basic Buster Raspbian. When compiling the Raid 1 disk in mdadm I get stuck at 6 percent. Got the pi to start a samba server on one ssd but can't get raid to work. Anyone got any ideas?
@marekslemensky4531
5 жыл бұрын
Nice video, but I think that this "stress" command didn't stress the GPU...
@bennyholgersson4686
4 жыл бұрын
If you overclock it to 2Ghz, can the Pimoroni Fan still keep it below 80c?
@chukwuemkaokafor2966
5 жыл бұрын
intresting
@maximumvariety8137
4 жыл бұрын
All is good until I put in..... sudo nano -w my-temp.sh at this point in the video he says he's going to edit file and I assume he hits enter after entering the line above.(does he? or does he do something special to edit file?) It takes me off of the main screen with the "my-temp.sh" listed at the top with commands at the bottom but there is no text at all. I ctrl exit out and when I enter.... sudo chmod +x my-temp.sh it says .... chmod: cannot access 'my-temp.sh": No such file or directory Please advise
@PST101
4 жыл бұрын
Copy and paste the code into the empty screen. He already has the file created. You don't. Code is in the link provided in the description.
@GhostyOcean
4 жыл бұрын
Inside my my-temp.sh script, the console says permission denied when I try to get the CPU temp. How do I fix this? I've tried forgoing defining cpu and putting the temp location (like you did on the console earlier in the video), and it did notice useful. Either I get an error that says permission denied, I get a 0 where the temp output should be, or it acts like there is nothing there and doesn't print the CPU temp.
@GhostyOcean
4 жыл бұрын
I can get the CPU temp in the console, just not in the script??
@aracelicasillas6850
4 жыл бұрын
I had the same problem, the first time you run the comand you have to type: sudo chmod +x my-temp.sh and then type: ./my temp.sh. it worked for me
@pilovali
5 жыл бұрын
shmod? I always say c-h mod.
@isaackarjala7916
5 жыл бұрын
He said chmod.... 'ch' and 'sh' aren't pronounced the same
@erikjohnson9112
4 жыл бұрын
Mod Shmod. Yeah, I don't treat it as a single word, preferring c-h mod.
@devdeque7846
5 жыл бұрын
People who worry about Rpi cooling are fairly idiotic; no offense. But if you're pushing the system hard enough to consider cooling ... First, ask yourself why are you using the Rpi in the first place? Use something else and have a better experience. Or like the people who dive deep into overclocking them. You might as well overclock a ham sandwich with extra mayo thermal paste while you're at it because that makes more sense.
@erikjohnson9112
4 жыл бұрын
R.Pi 4 is a much hotter beast than 3, so you comments mattered more in the old days. Without a solid heatsink, throttling is very much a thing. Aluminum cases that thermally connect to the CPU (and perhaps memory) are very effective. I just got an Argon One case and passive cooling works quite well, with a fan that only engages based on heat. Really depends on why you Pi (yes, making it a verb might annoy some, but it is concise).
Пікірлер: 53