Excellent...as always. Axiom has so much more horsepower than I realize ..thanks to your presentations. You should build these into a tutorial that is searchable on the Axiom.
@RaymarineInc
3 жыл бұрын
Thanks for the comment, Pete! We appreciate you tuning in!
@grindene
8 ай бұрын
Thanks to your video I switched back to Raymarine from Garmin on my new Boat. It will have 2 mfds, sonar,radar,vhf++. So thanks for the great information in this videos. Keep it coming 😊
@RaymarineInc
8 ай бұрын
Thank you for watching and coming back to Raymarine!
@gordonhenderson5912
Жыл бұрын
Ooi Mate, I am a total technophobe but you explanations were amazing. All the way in the antipodes and you make it sound so simple. I’m off to see how I go. Thank you so very much for your unsolicited help
@RaymarineInc
Жыл бұрын
Thank you for watching, Gordon!
@romeowhiskey1146
3 жыл бұрын
Jim, Another GREAT presentation, as always.
@RaymarineInc
3 жыл бұрын
Glad you enjoyed it
@bjasoncrew
3 жыл бұрын
This was an excellent webinar. Thanks for this.
@RaymarineInc
3 жыл бұрын
Glad it was helpful!
@jamesboyd1355
3 жыл бұрын
Hello Jim, I bought an axiom 7 a couple of weeks ago, replacing a garmin unit. Your videos have helped me understand the features of the device in a way that would not have been possible without them. It is fitted to my moody 336 yacht here in Largs Scotland. Thanks very much and my congratulations on a most informative series delivered in an entertaining fashion
@RaymarineInc
3 жыл бұрын
Welcome to the Raymarine family, James! Thank you for watching our broadcasts.
@bramnieuwland9960
Жыл бұрын
Hello Jim excellent webinar. Thanks for this.👍
@RaymarineInc
11 ай бұрын
Glad it was helpful! Thank you for watching!
@michaeltetterton8655
3 жыл бұрын
You do an amazing job teaching Axiom
@RaymarineInc
3 жыл бұрын
I appreciate that! Thank you for watching!
@danielslocum7316
Жыл бұрын
In general, the TI units are faster in response to inputs. This is seen when quickly switching between sonar, downscan, chart, and split screens kzitem.infoUgkxeAxH15LxhjGlg5-CRYqjTGTEH0tbY4vk recommend The Hook units will show some lag on button pushes and screen switching. The big ticket item though is maps. If you install a mapping card such as Navionics or the free C-Map Genesis which has a lot of map detail, then moving around the map with the cursor or when running down the lake can lag significantly on the Hook units, but is seamless with the TI units.
@RaymarineInc
Жыл бұрын
Thanks for watching. Its possible to use Axiom on large and small boats alike.
@andrewp634
Жыл бұрын
This has been so helpful, need watch loads more. I can get the best out of my Raymarine stuff.
@RaymarineInc
Жыл бұрын
Thanks for watching, Andrew!
@garrykennedy5653
3 жыл бұрын
I really appreciate your information I have learnt a lot from you
@RaymarineInc
3 жыл бұрын
Glad to help
@mcarlson4854
3 жыл бұрын
Great Teacher !!!
@RaymarineInc
3 жыл бұрын
Thank you! 😃
@josephinegobel1542
Жыл бұрын
This was super helpful. Thank you so much!!
@RaymarineInc
Жыл бұрын
Thank you for watching!
@icannevergetthistowork
3 жыл бұрын
Great Video! Very impressed with the presentation. Thank You!
@RaymarineInc
3 жыл бұрын
Glad you liked it!
@kvdbonyoutube
3 жыл бұрын
Great Information!Thanks.
@RaymarineInc
3 жыл бұрын
You're welcome!
@Propman203
3 жыл бұрын
You make it look so easy
@RaymarineInc
3 жыл бұрын
Thanks John. I am happy to pass my knowledge on and make you an expert too!
@flash521
3 жыл бұрын
I have been viewing since beginning. Some have not been applicable, however, most give allot of value. Tonight - data boxes
@RaymarineInc
3 жыл бұрын
Hi Flash. Thanks for watching! I am glad you're finding them helpful. If there are topics you'd like to see covered in the future, feel free to comment here.
@franshorjus5308
3 жыл бұрын
Excellent session, thanks a lot
@RaymarineInc
3 жыл бұрын
Most welcome! Thank you for watching!
@larry9210
3 жыл бұрын
Very nice. I wish B&G produced such useful videos!
@RaymarineInc
3 жыл бұрын
Thank you! I'm glad you like the content. Let us know what you'd like to see in the future and we'll try to get it in the broadcast. Also, feel free to repurpose your B&G stuff as a boat anchor. We won't be sad. :-)
@larry9210
3 жыл бұрын
Ha! I do have Raymarine MFDs and Radar on my cruiser.
@greggronemeier1256
3 жыл бұрын
Great presentation !
@RaymarineInc
3 жыл бұрын
Glad you liked it!
@patxicascante
3 ай бұрын
Muy buena explicacion. Gracias.
@RaymarineInc
3 ай бұрын
Thank you for watching!
@leijohn154
3 жыл бұрын
Thanks for the info for setting fishing zone
@RaymarineInc
3 жыл бұрын
Thank for watching! I hope the fishing season is going well out there!
@richardquarantiello6318
3 жыл бұрын
Great job Jim
@RaymarineInc
3 жыл бұрын
Thanks for watching, Richard!
@gregdrew1558
Жыл бұрын
great stuff.thanks greg in Oz
@RaymarineInc
Жыл бұрын
Glad you enjoyed it! Thank you for watching. New episode coming this Thursday!
@bramnieuwland9960
3 жыл бұрын
Excellent thanks
@RaymarineInc
3 жыл бұрын
Glad you liked it
@s.e.covingtonco3232
3 жыл бұрын
Great Presentaion - thanks
@RaymarineInc
3 жыл бұрын
Glad it was helpful!
@AlbinStratusCalima
3 жыл бұрын
Great live stream
@RaymarineInc
3 жыл бұрын
Thank you for watching!
@janeriksen4736
3 жыл бұрын
Very interesting presentation! One question to routes and waypoints: is it possible to set a wanted ETA for a specific WP in a route? This could be to arrive for a bridge opening or to reach a tidal current and then the previous WPs are adjusted to rematch this ETA ( and thereby of course also help to decide departure time from first WP).
@RaymarineInc
3 жыл бұрын
Hello Jan. This is a fantastic idea, and unfortunately I am not aware of a way to get the system to generate it. Your scenario of trying to make a bridge opening or some other deadline makes perfect sense though. I will make the suggestion to our team.
@chuckmosolf3391
Жыл бұрын
Great tutorial‼️‼️
@RaymarineInc
Жыл бұрын
Glad you liked it
@gregjackson7591
3 жыл бұрын
Great Video,, keep it up very helpful!
@RaymarineInc
3 жыл бұрын
Glad it was helpful!
@romeowhiskey1146
3 жыл бұрын
Jim, Another thought... YTube Title RAYMARINE LIVE: Chartplotter Basics. Suggestion: RAYMARINE LIVE: AXIOM Chartplotter Basics. While searching for "AXIOM chartplotter" in YT...the FIRST title doesn't appear...missing a lot of potential users/customers.
@RaymarineInc
3 жыл бұрын
Thank you! I'll take a look at that.
@summergrillo9655
3 жыл бұрын
great video. thanks
@RaymarineInc
3 жыл бұрын
Glad you liked it!
@anderseklund364
Жыл бұрын
Hello; I have been a Garmin user the last 18 years, but now bought a new boat which had Raymarine stuff installed beforehand. One thing that was missing though, was the VHF radio. Equipment in the boat: MFD Axiom Pro RealVision 12.1" Autopilot EV200 Echosounder CPT 120 CHIRP Radar Quantum II Doppler Q24D Impressing set up I have to admit.. But I'm missing one function, that is the possibility to make a direct call with the VHF from touching the AIS symbol on the plotter, select call in the scroll down menu, and the VHF automatically gets the MMSI nbr without me having to put it in there. This is a very good function in the Garmin system, that I really will miss with the Raymarine system. I've now investigated with experts here in Sweden and i does not makes any difference which VHF i choose. I will not get the wanted function regardless of which VHF i choose. So, I'm going for a RAY73 which have the AIS integrated and communicates this to the plotter.
@RaymarineInc
Жыл бұрын
Hello Anders. Welcome to Raymarine! The ability to touch on an AIS contact to make a DSC call is something on our product wish-list. Hopefully we can add it to our system.
@ingriddoorn1201
Жыл бұрын
You explain everything so easy, thank you 🙏 I’d love to know why when I plan an autoroute I don’t see the total length of my create route
@RaymarineInc
Жыл бұрын
Hello Ingrid. Thanks for watching the show! The best place to see the overall length of your route is in the route plan. After a route is created you'll see 3 popup options for Follow, Route Plan, or Exit. Touch on Route Plan and you'll see a grid and small chart preview showing all the intermediate waypoints. In the column labeled distance you'll see 2 values listed. The first number is the length of that route leg, and the number below it in parenthesis is the cumulative distance. If you scroll to the last waypoint in the grid, you'll see the overall distance it covers. You can also see the route plan at any time by long pressing on any leg of the route, and selecting Route Details from the popup menu. That will bring you to the same route plan.
@ingriddoorn1201
Жыл бұрын
Thank you so much, I’ll give it a try in a few hours when I’m back on the boat 👍👍
@gboulet69
2 жыл бұрын
Très bon vidéo merci.
@RaymarineInc
2 жыл бұрын
Thank you for watching.
@charliejacobs4137
3 жыл бұрын
I have an Axiom 9 in the cockpit and an es78 at the nav station as the slave. The latest Lighthouse update appears to be for the Axiom only. Will an update to the Axiom prevent the network from operating properly because the es78 is on a different update version?
@RaymarineInc
3 жыл бұрын
Hello Charlie. If you updated your eS-Series to LightHouse 3, you'll want to keep your Axiom at the same software level. The last LightHouse 3 release for eS-Series units was 3.11 Cannes. Your Axiom should also remain at 3.11. There are features in the later LightHouse 3 Axiom versions that are not supported on the older eS-Series hardware. Running different versions on your mixed-display network could cause instability or crashing.
@petemather6017
Жыл бұрын
How best to draw out your new Raymarine System for a 43ft sailboat. Autohelm, linear #2, ACU 400 and EVO 2, Quantum Doppler 2 radar, 3 axiom 9", speed /depth Dst810, wind, Remote on Seatalk 1 and 3 I-70. Oh just added a RMK-10 to work the axiom 9 on the mast from the cockpit. Raynet distribution box is also on board.
@RaymarineInc
Жыл бұрын
Hello Pete. Your local Raymarine dealer is your best resource for this when planning a new installation or upgrade. Many of them can provide full drawings of the new system. Its a great way to validate the networking and to make sure it is all going to work together, before you order anything.
@mogggggg1
11 ай бұрын
Hello, I have the axiom pro16s, and I have Volvo Kamd300a engines with analogue dials , can I run the engine and fuel data on my axiom ? And how can I do that ? thank you for this channel it’s helped so much, Tony
@RaymarineInc
11 ай бұрын
Thanks for watching! I suggest getting in touch with Yacht Devices, who makes a few different engine gateway devices that work with 2000's era Volvo engines. Many Volvos from that era outputted either J1708 or J1939 data. Axiom is looking for NMEA 2000 engine sentences. The Yacht Devices gateways can translate from the automotive/industrial protocol to the marine industry protocol. You can find them online here: www.yachtd.com
@ejdd3442
Жыл бұрын
I purchased the Axiom with Navionics because of the auto-rout my Garmin was 10 years old. I am so disappointed that the front screen does not show the total trip ETA, the randomly placed waypoint ETA has no value, not even the time of day, compared to my Garmin this seems to have brought me back 20 years. Also I am in buzzards bay where the direction of the current plays a very important role, the Garmin displayed this this information live but not on the Axiom.... I will install the Axiom down below and bring the Garmin back to the wheel.
@RaymarineInc
Жыл бұрын
Thanks for the comment. Total trip ETA as a databox item is something on our list to get into a future update. Current can be displayed on your Axiom's chart. Touch Menu...Layers...Tides. In Raymarine-speak "Tides" covers both tidal height as well as tide-generated currents. You should get tidal arrows at key locations on your chart. You definitely have some serious tidal flow there. I spent some time at the "Cape Cod College of Nautical Knowledge" back in the 1990's, right there on Taylor's Point. If you have trouble finding the tides, please feel free to email me at james.mcgowan@Raymarine.com.
@johngrimm1496
Жыл бұрын
I have my axiom at home for winter. How can I use my home fyi to update my unit
@RaymarineInc
Жыл бұрын
Hello John. You'll need to connect your Axiom to a 12-volt DC power supply to bring it to life. Once its on go to Home...Settings...and on that first tab is a button to Update Software. Touch it, then choose Check Online, and then you'll have a popup for Wi-Fi Settings. Touch it, choose your home network and enter the password. Once Axiom connects close the Wi-Fi menu and then touch START. Axiom will connect to our server, look for updates, and present a list of what is available. By default there will be a check-mark next to any items needing updating. Touch the UPDATE button to proceed. It takes Axiom about 10 minutes or so to update itself on a fast Wi-Fi connection. We also have a couple of videos showing the process. Here is a link to one of them: kzitem.info/news/bejne/s5puuqSaj5lhgXY
@ChrisWilson-nw4gk
Жыл бұрын
Just started watching your ray marine talks here in the U.K I have Raymarine instruments on my 11 mtr yacht including an Axiom 9 with the latest software and Navionics. My question is I am struggling to find and use Anchor Watch . Can you please help . Chris Wilson
@RaymarineInc
Жыл бұрын
Hello Chris. I'll try to cover anchor mode in detail in a future video, but in a nutshell, here is how it works. When you are going to anchor switch your chartplotter into Anchor mode. Axiom uses some measurements from your boat, along with live GPS position and water depth to help you decide how much anchor rode you will need. If you prefer to use more or less chain, you can adjust it to your preference. The anchor mode display shows you a detailed chart display with wind and tide vectors overlaid on it to assist in gauging how the boat will drift when stopped. When you reach your drop point, stop, and drop anchor, you'll touch the Mark Anchor Position button. The GPS position of the anchor's resting point on the bottom is saved. You can now begin backing down and paying out chain to the suggested length. When the chain is fully deployed, touch CHAIN OUT. You'll have the option to adjust the final length of chain, reset the entire process (Raise Anchor) or activate the anchor alarm. On-screen you'll see the boat's calculated swing radius as well as its drag circle. Should the boat exceed the drag circle, you'll receive an anchor dragging alarm. If you have not seen it, I highly suggest checking out the Axiom LightHouse Advanced Operating Guide, available on Raymarine.com. The Anchoring Mode is described in detail starting on page 215. You can get the manual here: raymarine.app.box.com/s/rvhycb6x1brzo64921k5tsqwv2ica3j6/folder/200926262503
@pjssbbx
3 жыл бұрын
My issue with using Automatic Route is that the system prefers marked channels. It won’t pick the shortest route even over deeper water within my boat’s set parameters. A typical trip from my dock to a local wreck site is 6 NM and takes 15 minutes. Using automatic route it would be 18 NM and take 49 minutes going the long was round!
@RaymarineInc
3 жыл бұрын
Hello Paul. I would be curious to know where you are boating, and what that destination is just so I could take a closer look at it. If you could, send me an email to james.f.mcgowan@raymarine.com and included where you are starting, where you are going, and your boat's particulars. There really aren't any user-adjustable variable in the auto routing algorithms other than the input for the boat's draft (on Navionics) and draft, height and width (on C-MAP.)
@borysnijinski331
3 жыл бұрын
Could you do a presentation on differences between Lighthouse 3 Dartmouth and Edgartown...what features or improvements have been added.
@RaymarineInc
3 жыл бұрын
Hi Borys. I'll see if we can get something like that it. We did one early in 2020 comparing Lighthouse Annapolis, Bermuda and Cannes. In the mean-time, we do have a software change history available here: www.raymarine.eu/service-and-support/software-updates/mfds/lighthouse3/axiom-models.html Scroll down to the bottom and you'll see tabs detailing the current release and prior releases.
@rogermoar3983
5 ай бұрын
Does the auto routing compensate for great circle sailing distances or just rhumb line
@RaymarineInc
5 ай бұрын
Axiom does plot a great circle route if you manually plot a start point and a distant destination. You can see it if you range out and drop a waypoint out-to-sea. The track line it plots will be curved. You can follow that trackline either manually or by autopilot. When you say auto routing though, I'm not certain if you mean the basic ability to plot a route and follow it with your autopilot, or if you are referring more specifically to the Navionics or C-MAP automatically generated routes where you simply specify the destination and their algorithm figures out the best way to get there. With routes figured out automatically by those automated systems I am not certain that Great Circle routing would truly factor in to them. I say this because they tend to automatically inject intermediate waypoints along the track. I will need to do some research and confirm, but I think there are some limitations as to how far of a distance over which they can automatically generate a route. When you have a moment, please send me an email to james.mcgowan@raymarine.com so I can get back to you on this. I will try to find out a bit more about how the automatic routing system behave over longer distances where Great Circle routing would be a factor.
@vassilisfragakis3534
8 ай бұрын
Hi, I have a navionics subscription on my iPhone. I also bought an axiom plotter. Can I transfer the navionics maps to axiom? Or should I buy a second subscription for the axiom too? Thanks
@RaymarineInc
8 ай бұрын
Navionics considers the subscription attached to the mobile app to be a separate entity from the subscription for any maps plugged into the Axiom chartplotter. If you want to synchronize chart updates between mobile and the chartplotter you do need to have an active subscription for both devices.
@ME-qq2dc
2 жыл бұрын
Can the system automatically adjust for daylight savings starting and stopping based on your region, or do you have to remember to change it? Thanks
@RaymarineInc
2 жыл бұрын
Hello ME. Raymarine systems do not automatically adjust for daylight savings time. You will need to change it yourself. Fortunately it is very easy on Axiom. On the home screen touch the clock, located on the top, right corner. Touch Time Offset from UTC and adjust your time zone accordingly.
@jeffpanella4565
Ай бұрын
My Axiom is often has a delayed boot up or will just say Axiom for an entire trip unless I reboot the batteries and sometimes that doesn't work. Axiom is great but this is super annoying. How can I get this fixed without sending back the unit?
@RaymarineInc
Ай бұрын
Hello Jeff. I suggest updating your software to make sure Axiom is running the latest version. Currently, version 4.6 is the most current. You can download it from Raymarine.com to a microSD card and install it that way, or, if you have internet access onboard Axiom can update itself. Go to Home..Settings...Software Update...Update Online. Your system might also benefit from a factory reset. There is a memory buffer inside Axiom that it uses for various functions. There might be some corrupted or old junk information in the buffer causing the slowdown. If you have waypoints and routes you want to keep you can back them up before resetting. Go to Home...My Data...Import/Export...and use the "Save My Data" button to create backups on your map or memory card. Once you have backed up, go to Home...Settings...This Display. Factory Reset is on the bottom. Once Axiom restarts you can restore your data in that same Import/Export menu using the Import from Card function.
@jimschumacher9763
11 ай бұрын
Hi Jim- I'm running a full compliment of RM sailing instruments through 2 Axiom plotters. Have really enjoyed the new sailing upgraded features. The plotters started acting up shortly after installing a remote Smart Controller (w required converter). I've updated all instruments via online only to get error messages for the plotters. One plotter reports "not sufficient space", the other reports "failed to start". I've even tried factory reset before updating only to receive the same messages. Both plotters "work" but don't show the recent sailing features. One plotter drops numeral sixes behind the boat's icon as it travels over the screen. Really! Any advice?
@RaymarineInc
11 ай бұрын
Hello Jim. In order for Axiom to complete a software update there needs to be sufficient space in its internal or microSD memory storage space for it to unpack the software update before installation. 1st generation Axiom displays have a bit less built-in memory than the newer Axiom+ models, so are more susceptible to being full enough that they can't perform a software update using only their built-in storage. They will instead temporarily use a small portion of the empty space on the microSD card that is installed in the unit to perform those needed installation tasks, and then remove those files at the end of the process. In your case you'll want to make sure there is a microSD card plugged into both of your Axiom displays to give them that extra space. Any card 8GB or larger will be sufficient, and I suggest just leaving it installed in any display that does not already have a chart plugged into it. That will prevent this kind of issue during future updates. When updating, if the only microSD card plugged in happens to me a map card, Axiom will use some of the empty space on it if there is enough. If you are not comfortable with it doing that, you can temporarily eject the map card, replace it with another microSD of suitable size, perform the update, and then swap cards back at the end.
@CaptnButch
3 жыл бұрын
Great overview of all the basic functions. Great series! I notice that all of the views you showed are a standard birds eye view with paper map style display. Are there different views available while following a route?
@RaymarineInc
3 жыл бұрын
We currently only support the Birds-eye view on our systems, though there are options that will change it up slightly. You can offset the display 1/3 or 2/3 to give you more look-ahead. You can also adjust the visible layering on the chart to add or remove satellite photo overlay, radar overlay and other elements. I'll be showing off many of those features in an upcoming broadcast.
@bitsurfr46
Жыл бұрын
I want to auto route from my dock to Saint Augustine, but there is a low bridge in between. What do I do, make one route to the bridge and another to Saint Augustine?
@RaymarineInc
Жыл бұрын
The automatic auto-routing for Navionics charts actually does not take into account vessel height in its calculations. In theory you could probably do it all in 1 route and it would take you right through there. Since you know that bridge is an issue though, suggest breaking it into 2 parts. Route from your dock to the bridge (or wherever you are going to bypass it) and then create a new auto route from the other side of the bridge to your destination. I strongly suggest pulling down our LightHouse Advanced Operation Manual and reading the section on automatic routing. It is very important to understand which parameters it observes, and which it does not. Here is an excerpt from it: Autoroute - compatible cartography vendors The Autoroute feature is compatible with the following cartography vendor features. • Navionics® Autorouting. • Navionics® Dock-to-dock • C-MAP® Easy Routing Differences between automatic route generation functions There are important differences between the way different vendors handle automatic route generation. Depth clearances (Tidal height) • Navionics® Autorouting and Dock-to-dock avoids shallow areas based on the user defined [Minimum safe depth] setting plus an additional Navionics® safety margin. it assumes the lowest tide level, normally Lowest Astronomical Tide (LAT). The tide can be lower than LAT due to atmospheric effects such as high air pressure, wind direction, etc. • C-MAP® Easy Routing assumes that there will be some tide. The user must apply their own safety margin as appropriate to current conditions. Route legs that cross areas shallower than the user defined [Minimum safe depth] setting are marked with hazard waypoint symbols, it is critical that these legs are checked to ensure that there is sufficient tide to avoid the hazard. Width & Height clearances • Navionics® Autorouting and Dock-to-dock does not use the user defined [Minimum safe width] or [Minimum safe height] settings when generating routes. Objects with width / height constraints are marked with hazard waypoint symbols, it is critical that these legs are checked to ensure that there is sufficient clearance to avoid the hazard. • C-MAP® Easy Routing uses the user defined [Minimum safe width] and [Minimum safe height] settings to determine if sufficient clearance is available. The user must apply their own safety margin as appropriate to current conditions. The Height datum must be checked, as it could be Mean High Water Springs (MHWS) or Highest Astronomical Tide (HAT). In both cases the tide can be higher than the datum due to atmospheric effects such as high air pressure, wind direction, etc. Reviewing an automatically generated route Before following any route you must ensure that it is safe to do so. Upon Route completion: 1. Range in on each route leg and waypoint that make up the Route. 2. Check either side of the route leg and around the waypoint for any possible obstructions. Obstructions can be charted objects or restricted areas. Routes generated automatically should use the caution waypoint symbol in areas where there are possible obstructions. 3. Where obstructions exist move the necessary waypoints so that the waypoint and route leg is no longer obstructed. The latest LightHouse 4.1 Advanced Operation Manual is always available as a free download on Raymarine.com in our Manuals and Documents section: raymarine.app.box.com/s/3t839g2xf6nko4n0h9re535140rknnpz/folder/21066102633 The automatic routing starts on page 125.
@Entryman100
2 жыл бұрын
I just bought an Axiom+9 with Light house 3. I hooked it up on my boat just to check it out, I could see the autopilot wheel position. I then took the unit home and upgraded to Light house 4 software. Now the Axiom display does not show the wheel movement. but it does show on the autopilot control. Is there a way to get this function back. I am running ST60 instruments.
@RaymarineInc
2 жыл бұрын
Hi Robert. We are chasing a bug right now in the Lighthouse 4 software related to that rudder angle indicator dropping out. We have a fix in the works and will be releasing a Lighthouse 4 update before the end of the month that will squish that bug and a few more that have been brought to our attention. If that is critical, you can roll-back your display to LightHouse 3.16 by downloading it from our website to a microSD card, and installing it through the MFD's card reader.
@darylvanness9889
Жыл бұрын
Just purchased a axiom 12 rv and it included lighthouse premium. All hooked up and I put the micro card in and seems lighthouse isn’t loaded it’s not a detailed map . What do I need to do to activate? Thanks
@RaymarineInc
Жыл бұрын
LightHouse charts for North America are pre-loaded with US and Canada charts. Plug it into your Axiom, launch the char app, and go to Menu....Settings....Cartography. Choose LightHouse charts as your preferred chart source from the menu there and the detailed map should load. The "Premium" content is not pre-loaded on the card. For that you will need to visit chartstore.raymarine.com and activate your 1-year Premium subscription using the voucher code that was included with the map card. There you can add satellite photos, streets, and premium points-of-interest to your card. It will also check to make sure the charts are up-to-date.
@davidmerrill5087
3 жыл бұрын
Can you show or tell me how to find the steer line showing on and off course for steering the boat to a waypoint manually ?
@RaymarineInc
3 жыл бұрын
Hello David. I think you might be looking for the "rolling road" display, which is part of the Dashboard app. When you have a waypoint in-track, open the Dashboard app and you'll see a navigation page with a visualization of a road. Your waypoint is ahead, on the horizon, and the boat's position in the lane is representative of your cross track error.
@SailingwithobsessionML
11 ай бұрын
Hi Just bought a 12 inch Raymarine axiom chartplotter and I do not see a way to network my unit did I buy the wrong model
@RaymarineInc
11 ай бұрын
There is a single "Network" port on the back of your Axiom. That is your RayNet high speed Ethernet connection. You can connect directly from that port to another RayNet device like a radar scanner, another Axiom, sonar module, SiriusXM receiver, etc. If you have more than one device you need to connect to, you'll need to add a network switch to create more network ports. Our RNS-5 or RNS-8 network switches give you either 5 or 8 ports, respectively, to accommodate additional Axiom displays, sensors, scanners, and accessories.
@Vepoch
2 жыл бұрын
Hi. Not sure if you are still answering questions here but. I’m trying to connect my brand new Raymarine plotter to my cell phone hotspot to update my software and it will not stay connected. It toggles between being connected for 1 second to being disconnected for 1 second over and over again until I just turn Wi-Fi on the unit off. Have you seen this issue? Any suggestions. I’m also getting a connection error when trying to sync my Navionics app to my plotter. I’d like to move my pre saved routes over from my phone to my plotter.
@RaymarineInc
2 жыл бұрын
I have seen a similar issue on my unit when trying to link it to Wi-Fi on my iPhone and the iPhone's "Private Address" switch is turned off in the Wi-Fi network. You might try switching that off and making your connection.
@jimoconnor5973
2 жыл бұрын
I'm having difficulty getting my "Boat Details" entered into my Axiom Pro. Particular the names and numbers of tanks. In the Lighthouse 3 manual on page87 it shows tanks named Gas 1. My Boston Whaler only has one tank, when the dealer installed my Axiom Pro he put in 2 tanks. How do I get boat details to show one tank named "Gas 1" with a capacity of 58 gallons? All other parts of the Boat Details seems to work OK
@RaymarineInc
2 жыл бұрын
Hi Jim. If the number of tanks are off, you might need to reset the display and run the startup wizard again. Go to Home...Settings....This Display....and select Factory Reset at the bottom. The wizard will run after it restarts. Something important to know on tanks is that our system differentiates between "Fuel" and "Gasoline" tanks. Fuel tanks can be designated as Propulsive or Non-Propulsive. Propulsive fuel tanks are counted towards fuel economy calculations. Non-Propulsive are not. Also, tanks designated specifically as Gasoline are not counted in fuel economy calculations. We do this to make accommodations for boats that have dedicated tanks for generators vs. propulsion, or for boats that have both diesel and gasoline tanks. In case you missed it in my reply to your other comment, definitely check out the Tank Manager section of the LightHouse 4 Advanced Operation Manual, available here: raymarine.app.box.com/s/3t839g2xf6nko4n0h9re535140rknnpz/folder/21066102633
@Dachamp2001
2 жыл бұрын
I was looking at a boat down in Tampa but Pittsburgh is the closest water way to me how would I set a route & fuel for this trip?
@RaymarineInc
2 жыл бұрын
Axiom has the ability to automatically generate routes if you are running Navionics or C-MAP cartography. There is a limit as to how far you can go on a single route, and a limit to the number of waypoints in the route, so I do not recommend trying to automatically route the entire trip from Tampa to Pittsburg in a single route. Instead, break it down into segments that you can cover in a day or 2, and save them individually as routes. Creating an autoroute can be as simple as long-pressing on your starting point and selecting Build Route from the popup menu. Then pan the chart to your destination, long-press again, and select AutoRoute to Here. Before you can use automatic routing you do need to setup some basic parameters about your boat in the Vessel Settings menu. Go to Home...Settings...Boat Details to set up your boat's height, width and draft. Our most recent Raymarine Live episode had another segment on automatic routing. You can see it here: kzitem.info/news/bejne/pYqjs3uMpWd2imU This link jumps right to that segment in the show.
@stevemorgan7144
2 жыл бұрын
Can you show the complete system and it’s all connected peripherals
@RaymarineInc
2 жыл бұрын
Hi Steve. We'll try to get a "system builder" type of episode in a future episode. You can find some examples in our Networking section here: www.raymarine.com/view/index-id=3011.html Another good resource is the installation guide for the Axiom MFDs. There are some sample diagrams in there showing the MFDs and peripherals.
@njsarn
Жыл бұрын
Jim, thanks very much for your presentation, very well put together. I have Axiom pro 9, Axiom +9 because of your good explanation of what they can do. Question -> How do I program the i70s so that it looks like the picture on the box? I've gone through practically all the settings, created new pages added the instrument tiles and associated data but can not manipulate the tiles on the Multi instrument page. Thanks very much again for your help.
@RaymarineInc
Жыл бұрын
Hi Nat. I think the display you are looking for is called "Heading - Multi Gauge." On your i70 you'll need create a full-screen page, and then go into the data category of Heading....and the multi-gauge layout in the one all the way at the bottom.
@njsarn
Жыл бұрын
@Raymarine yes, thank you. I got the Heading multi gauge page created. But it doesn't look like the picture on the i70s box. Can you ask your software team to recreate exactly that option (as pictured on the box Speed in the middle, heading at the bottom). The background color (as seen on the display box is also very desirable). Thanks much again.
@jlljjl
3 жыл бұрын
Keep these going... I continue to get excellent tidbits from these episodes. Any support updates for the Android raymarine Apps that are no longer supported/working?
@RaymarineInc
3 жыл бұрын
Hello J. This is something we're actively working on. I hope to have some positive news on it very soon.
@dondofam04
3 жыл бұрын
Will you be doing any live streams for the Element HV? I use my unit on a kayak and I feel that I’m not getting the best detail on my charts. Also, a discussion about what would be the best settings for a kayak as far as sensitivity, scroll speeds and HV since we move a lot slower. I’ve seen the Jim sammons videos, but it would be helpful if you can dedicate a live stream for the Element. Thanks for your help.
@RaymarineInc
3 жыл бұрын
Hi Dondo. We do hope to have an Element-focused stream in the next few weeks. In the mean time, I do suggest slowing down the scroll speed on your Element system. I am a kayaker too, with Element. I find the slower scroll speed delivers even sharper imagery. I also strongly suggest experimenting with some of the alternative color palettes offered on the system. Personally, I find that the ones with a white or light gray background are much easier to see all-around, and often give better contrast to the targets in the water.
@jordanwhyte3203
2 жыл бұрын
Just replaced my e127 hybrid touch with an axiom unit and it wont connect to my p70 autopilot and i was told by raymarine they r compatible together is there something im misisng here how to hook them up ?
@RaymarineInc
2 жыл бұрын
Hello Jordan. On your Axiom got to Home....Settings....go to the Autopilot tab, and make sure the autopilot integration is enabled. If you don't see the autopilot tab then Axiom is not detecting an autopilot being present on the Seatalk NG connection. Double-check that you have Axiom plugged into the SeaTalk NG network with your autopilot.
@nickrdgz9323
2 жыл бұрын
How can I add a speaker to my MFD to hear the audio functions from my apps or warning alarms?
@RaymarineInc
2 жыл бұрын
Hello Nick. There are a couple of ways to add louder audio for apps and warnings. If you have a Bluetooth audio system onboard you can connect Axiom's audio to it and hear it there. This could be your boat's stereo system or even a simple stand-alone portable Bluetooth speaker. Put your speaker into pairing mode, then go to Axiom's home screen. On the top right corner tap the row of icons and select Bluetooth Settings from the menu that pops up. Turn on the Bluetooth radio in Axiom if its not already on, and then it will display a list of nearby detected devices. Select your speaker and allow it to connect. You can then exit by touching the "0" button at the bottom center of the screen. Give your power button a quick tap or swipe and a shortcut menu appears. When Axiom is connected to Bluetooth, you'll see 2 volume sliders in here. One is for Apps that have audio (like Netflix or Spotify) and the other slider is for Axiom's alerts and alarms. Adjust them to your desired level. If you don't want to rely solely on Bluetooth, we also make an external alarm module that connects to your SeaTalk NG network. It repeats alarms generated by Axiom and other devices like instruments, AIS, autopilot, etc. This device is part number A80614. This will only do system alarms, but not app audio. This alarm is VERY loud, be warned!
@jeffh9288
3 жыл бұрын
Great Webinar, just a side note when reading manual for Freemantle its says Navionics does not take boat height and width into consideration in autoroute. Please confirm
@RaymarineInc
3 жыл бұрын
Hello Jeff. Thank you for pointing this out! You are correct that the Navionics Dock to Dock autorouting algorithm does not take into account the boat's height or width (beam.) Instead, it marks the auto-generated waypoints plotted near bridges or narrows with exclamation points to draw attention to them. We also support C-MAP Easy Routing on Axiom. The C-MAP algorithm does take into account vessel height and width in its calculation. For the benefit of anyone reading this comment, here is the official details from the LightHouse 3.14 Fremantle Handbook. Sorry for the long post, but it is worth a read: Autoroute - compatible cartography vendors The Autoroute feature is compatible with the following cartography vendor features. • Navionics® Autorouting. • Navionics® Dock-to-dock • C-MAP® Easy Routing Differences between automatic route generation functions There are important differences between the way different vendors handle automatic route generation. Depth clearances (Tidal height) • Navionics® Autorouting and Dock-to-dock avoids shallow areas based on the user defined Minimum safe depth setting plus an additional Navionics® safety margin. it assumes the lowest tide level, normally Lowest Astronomical Tide (LAT). The tide can be lower than LAT due to atmospheric effects such as high air pressure, wind direction, etc. • C-MAP® Easy Routing assumes that there will be some tide. The user must apply their own safety margin as appropriate to current conditions. Route legs that cross areas shallower than the user defined Minimum safe depth setting are marked with hazard waypoint symbols, it is critical that these legs are checked to ensure that there is sufficient tide to avoid the hazard. Width & Height clearances • Navionics® Autorouting and Dock-to-dock does not use the user defined Minimum safe width or Minimum safe height settings when generating routes. Objects with width / height constraints are marked with hazard waypoint symbols, it is critical that these legs are checked to ensure that there is sufficient clearance to avoid the hazard. • C-MAP® Easy Routing uses the user defined Minimum safe width and Minimum safe height settings to determine if sufficient clearance is available. The user must apply their own safety margin as appropriate to current conditions. The Height datum must be checked, as it could be Mean High Water Springs (MHWS) or Highest Astronomical Tide (HAT). In both cases the tide can be higher than the datum due to atmospheric effects such as high air pressure, wind direction, etc. Reviewing an automatically generated route Before following any route you must ensure that it is safe to do so. Upon Route completion: 1. Range in on each route leg and waypoint that make up the Route. 2. Check either side of the route leg and around the waypoint for any possible obstructions. Obstructions can be charted objects or restricted areas. Routes generated automatically should use the caution waypoint symbol in areas where there are possible obstructions. 3. Where obstructions exist move the necessary waypoints so that the waypoint and route leg is no longer obstructed.
@robertgray9280
2 жыл бұрын
I have an axiom 9 on a BW 170 Montauk, how do I get track info (Nautical Miles traveled) for a particular day. I have tracks for multiple days showing on my screen when I power the chart plotter on. Can I go back and get info from a certain day? For instance I wanted to see how many miles I traveled yesterday.
@RaymarineInc
2 жыл бұрын
Hello Robert. Axiom keeps track of total distance traveled, and also offers multiple resettable trip logs. If you go to Home....My Data....Fuel/Trip you will see them reported there. Axiom tracks a manual (resettable) trip log, distance for that day, distance for the month, and and distance for the season (resettable.) I don't see a way to go back and get numbers for a particular day though. I'll ask our software team about it and see if there is a way to do it I don't know about, or if it could be added as a future feature if we don't have it in there.
@atravels1055
2 жыл бұрын
How come the lat/long coordinates minutes have the ' symbol before the decimal, rather than at the end?
@RaymarineInc
2 жыл бұрын
Our Axiom displays support many different display formats for latitude and longitude. Depending on which format you choose, the symbols change just slightly. From the Home screen go to Settings...Units...Lat/Long format to see the different options. The example you asked about is latitude/longitude rendered as DD°MM'SS where the position is reading as Degrees, Minutes and Seconds. Depending on what you are doing, and also what other navigational tools you are interacting with, you may prefer to display it differently. We support all of the major variations including whole minutes, decimal minutes, while seconds, decimal seconds, etc.
@atravels1055
2 жыл бұрын
@@RaymarineInc thank you for the response. I am used to degrees decimal minutes DDM.
@pursiju
3 жыл бұрын
Thank you for these tutorials! If only every Axiom owner knew about these. Question 1: How to engage EV autopilot to follow route? After first season, I still am not sure I am doing it right. Once it is on, it steers the boat just fine. So what is the orthodox way to engage autopilot. Question 2: WAYPOINT 123 text is placed alongside each waypoint on the route. This waypoint format is too long for my map scenery. Editing of waypoint names under multi editing would be great. Example WAYPOINT 123 ---> WPT 123 with one command. Can waypoints be visible without names when attached to route?
@RaymarineInc
3 жыл бұрын
Hello Jukka. There are a couple of ways to tell your pilot to follow the route. On Axiom's home screen go to Settings....and select the Autopilot tab and you can turn autopilot integration on. This enables Axiom's on-screen pilot capability. For example, when you finish entering a waypoint or route, included in the ending prompts will be the option to follow the route with the pilot. You can also do it in s 2-step process using both Axiom and the pilot control head. First, select a waypoint or route and tell Axiom to follow it. Axiom begins sending nav data to the network automatically. Next, bring the pilot from Standby to Automatic mode. This locks the pilot on the current heading. Next, activate the pilot's Track mode from the control head. Menu....Mode...Track. The pilot will chirp and indicate the name and direction it intends to steer to head to the first waypoint. Press Track again to allow it to proceed. Note, if you are initially more than 0.3 nautical mile off of the plotted track, the pilot will first issue a Large XTE error message. When the cross track error is large, the pilot will first maneuver the boat to close-up the cross track error and get back on the plotted course, then it will turn towards the next waypoint. This maneuver is sometimes confusion to people who don't understand the pilot's logic. Waypoint names can be switched off if you don't want to see them on the chart. In the chart app go to Menu....Settings....Advanced and then scroll down to the MY Data Appearance section. You'll see the option in there to switch the names off, along with other related features.
@bobbyb314
2 жыл бұрын
ditto .. great series. 2 questions: [1] can the updated sections of the manual be downloaded so it's clear what's been altered or improved? [2] what about tide/current graphs like on the Navionics app for phones .. don't see anything using the same very simple graphics. Thanks!
@RaymarineInc
2 жыл бұрын
Hi Bobby. We released a new handbook for LightHouse version 4.0. Its available on Raymarine.com here: www.raymarine.com/service-and-support/manuals-and-documents/ There is a summary of new software features on page 22. Typically, we release a new version in PDF format with every software updated. The tide and current icons can be switched on or off on your MFD. The quickest way to see them is to put the chartplotter into "Tides" mode. In the chart app touch Menu....Mode....and select Tides. This simplifies the overall chart and turns on all of the tide and current reporting stations. Long-press on any one to see the detailed report and graph for that station. If you want to see the tide and current station icons all the time go to Menu...Settings...Layers and turn on the switch for Tides.
@helenvojtko9673
Жыл бұрын
I have a new Axiom Lighthouse 3 and would like to activate my 1 year Navionics subscription. Can I do this from the MFD on the boat? It is connected to the marina 5G internet
@RaymarineInc
Жыл бұрын
There are 2 ways to activate your 1-year Navionics subscription. If you have the Navionics boating app already on your Smartphone or tablet, you can connect it to the Wi-Fi access point on your Axiom screen and the app can detect, activate and update your chart card. To do this you do need to be running a paid version of their app with an active subscription on the app. This is a seperate subscription from what is included with your map card. The other way to do it is to unplug the Navionics map from Axiom and plug it into a computer with internet access. Navigate to navionic.com, click the link on the top of their site (My Card...Activate/Renew) and follow the prompts to create a Navionics account, install their updater app, and then it will update and activate the card.
@seanhansford9642
10 ай бұрын
Hi Jim Love watching your stream as thinking of purchasing a new chart plotter. I have an old 14 year old Ray marine chart plotter in an enclosure mounted in front of the wheel. i have a few questions before i commit to new replacement plus version. Does the axiom plus 7 & 9 support Imray charts UK that i feel they do but is there a trade off rather than purchasing Navionics or Lighthouse charts? Does the axiom have a trip odometer as my old ray marine MFD relied on a separate knot speed gauge to give distance travelled. This is very annoying as the separate unit gets stuck with weed from time to time but suddenly the separate speed gauge comes into life when travelling after freeing up the weed. My previous Garmin chart plotter recorded distance travelled over ground, Total distance for day etc and total from start of install. My current old ray marine chart plotter does not record unless linked to separate speed distance gauge! As mentioned above with weed problems this can be very inaccurate if linked to speed gauge. The Garmin i imagine worked out the distance travelled from A to B and why wouldn't it as it has location GPS details every step of the way in its memory. Why is my old Ray Marine MFD not recording it and if i change to new Axiom plus will it record this without a separate speed gauge connected? Bit worried about screen size and actual screen size without borders or surround . I was thinking of the Axiom + 7 but i can see dimensions online but for total size of unit. What i want to know is the height and width of the actual useable screen or map displayed in millimetres if possible. I have defiantly chosen to upgrade MFD to Ray Marine from original but i feel the axiom 7 might be too small to what i have and a axiom 9 might be too big for enclosure. Yes i anticipate you saying different options for enclosures but i would want to fit in original enclosure without having the cost of a bit of plastic! Just cant invisage the axiom +7 without actual viewable screen size. I am almost ready to press buy button but hovering over it as a few questions. If you can reply it would be great Jim. Very good Web broadcast. Regards Sean
@RaymarineInc
10 ай бұрын
Hello Sean. Thanks for watching the show. I'll try to pop all of the answers in here, but if I do miss one, feel free to email me at james.mcgowan@raymarine.com. Imray Charts for the UK are available for our Axiom systems. They are raster charts, meaning they are digital scans of paper charts. They are very accurate and detailed. The main difference you'll see between them and Navionics or C-MAP is how they work in a Head-Up presentation, and how they scale. Since the Imrays are raster, the text on them only reads correctly when north is at the top of the screen. If you happen to run in head-up chart mode, you'll be reading the text, depths, etc. from a different angle. There are also not as many zoom levels on them, again due to them being essentially large digital images. A Navionics, C-MAP or Lighthouse chart (by Raymarine) is a vector chart that renders according to the orientation selected, and it re-scales automatically for whatever level of zoom you select. All of our Axiom systems to have a GPS-based log that can be used to record miles traveled. We support the paddlewheel system too, but having both is convenient. There are actually multiple logs that can be set and reset independent of each other so you can easily keep track of lifetime, daily, and seasonal miles as you like. The actual screen area on an Axiom 7+ is 155 mm wide and 86 mm tall. Diagonally it measures 177 mm (7.0 inches). I hand-measured these just now with a ruler on an actual unit. For comparison the Axiom+ 9 is 200mm wide, 112 mm high, and 230mm diagonal (9.0 inches.) Feel free to email me if you have any additional questions.
@seanhansford9642
10 ай бұрын
Hi jim Thank you so much for reply and i will take onboard all that was said over a few days. Its so great to have input of questions asked and you have answered all my concerns so well done and nice to know there is someone out there to provide requested concerns. I have a few other questions but will send a message later as a bit complicated.... I will update to ray marine again for sure thank you.@@RaymarineInc
@Propman203
3 жыл бұрын
I’m having a problem with my bow icon it’s in the safety setting I chose the right one but it shows on my screen only a round dot any ideas why
@RaymarineInc
3 жыл бұрын
When you are stationary the GPS system can't tell what direction the boat is pointed at, so it shows your position as a dot instead. When you start moving the GPS can begin calculating your course over ground (COG) and it then changes the icon from a dot to the boat shape. If you want to see the icon displayed all the time you can add an electronics compass, heading sensor or autopilot to your boat. Those devices provide constant heading signal to the chartplotter.
@mattazevedo4515
3 жыл бұрын
Really enjoying these live series. Very well done. I am using an Element 9S running Lighthouse Sport software. Are all these functions available on my device as well?
@RaymarineInc
3 жыл бұрын
Hi Matt. Yes, just about everything we have shown is available on Element too. We are planning some Element-specific content coming up soon too.
@mattazevedo4515
3 жыл бұрын
@@RaymarineInc Fantastic! Looking forward to it.
@frankiepnightriderouternat2683
Жыл бұрын
Can I use this as a fish finder on my kayak ?
@RaymarineInc
Жыл бұрын
I run an Axiom 9 RV on my 12-foot fishing kayak. Powered by a 12-volt lithium, rechargeable battery pack. I'm happy to share the details on how I have it setup. james.mcgowan@raymarine.com
@lynnross5127
Жыл бұрын
I need to work with people on the AXIOM. How do I set up the demo boat?
@RaymarineInc
Жыл бұрын
Hello Lynn. You can activate Axiom's built in simulation by going to the Home screen. In the top, center there is an icon representing the name of the user profile that is running. If you've never setup a user profile, it will probably say Skipper and have a Captain's hat. Touch it to open the Profile Manager. The Profile Manager has 2 tabs, My Profiles and Demo Profiles. Touch Demo Profiles, then select what kind of boat setup you would like for it to simulate. Axiom will come up in simulation mode with a stream of fictitious, but realistic data. If you need to work on the chartplotter and want to move the simulated boat icon, simply scroll to where you want the boat to be, long press on the chart, and in the popup menu select More....Move Boat Icon Here. The boat icon will move on its own. If you enter a waypoint or route, it will track to it.
@user-of3ud6qz7v
Жыл бұрын
I have new T70161 EV-400 Sail Evolution auto pilot and new axiom E70638-00-NAG 12” Touch w/Navionics. Can I control my auto pilot from chart plotter
@RaymarineInc
Жыл бұрын
Yes you can. On your Axiom, touch Home...Settings....Autopilot and turn on Autopilot integration. This enables all of the autopilot functionality in your Axiom display.
@luisjosemirandavaldez4266
2 жыл бұрын
Hello, I have a Sailboat and I want to know how to determine the arrival time and the remaining miles to reach a specific point.
@RaymarineInc
2 жыл бұрын
Hi Luis. You can add a data item to your screen to show you the waypoint information and ETA. Data items can float over the screen, they can sit on the swipe-out data bar, or you can build them into dashboard pages. Check out this video that shows how to add them: kzitem.info/news/bejne/o22q2YGvnIt0f6Q
@user-eq4up4hw5r
2 жыл бұрын
With two axioms in a master/slave config, can you have the chart card in the master slot and have the data card in the slave slot so that when yo save data it goes to the slave card
@RaymarineInc
2 жыл бұрын
You can have map cards and data cards in all of the slots. Map cards are shared between all displays. You can access any map from any screen. This allows you to run more than one brand of mapping if you want to. For example you might want Navionics or C-MAP for navigation and then a specialty chart like CMOR or StrikeLines for enhanced fishing detail. On each MFD you can also specify to where any screen captures, video recordings, chart sounding recordings, etc. are saved.
@leigong9992
3 жыл бұрын
Hi Jim, Can you please let me know how to fix the problem with fishing zone setting. The fishing zone option is in grey not adjustable on my raymarine axiom 12 rv. Thanks a lot.
@RaymarineInc
3 жыл бұрын
You probably need to activate or renew your Navionics Freshest Data subscription. Fishing Zone, along with auto-routing, shallow water shading, PlotterSync, SonarChart Live and some other features are subscription-based items that are locked or unlocked by your charts. When you purchase a Raymarine display with Navionics included, or purchase Navionics chart individually from a dealer, a 1-year subscription is included. To activate it you'll need to plug your chart into your computer connected to the internet and visit Navionics.com. On their homepage there is a link on the top..My Card...Activate/Renew. Click the link and follow their instructions to install their Chart Installer app and activate your subscription. If you previously activated it and your year has run out they will offer you the option to renew your subscription. It costs $99 and allows you to update your charts with the latest data (they actually change daily) plus use their advanced features. Axiom checks to see if your subscription is active or not and locks or unlocks those Navionics-specific features. There are 2 places you can normally see it. On the homepage touch the Settings icon. On the first tab "Getting Started" your Navionics subscription status is indicated there. You can also check it in the Chart app. Touch Menu....Settings...and the first tab that appears is "Cartography" and you'll see your Navionics card below in the list of available charts. The title information there includes the activation status and expiration date.
@jeffh9288
3 жыл бұрын
Any reason one wouldn't use the Axiom to control EV-100 besides taking up space on your Axiom screen. Seems like you have same functionality as you would with p-70r control head, actually I noticed the Axiom gives you a little more. I saw you can jog 10 degrees at a clip when steering to a heading, not a option on the P-70r Thanks Jeff
@RaymarineInc
3 жыл бұрын
Hi Jeff. You can use the Axiom to control many of the pilot features, but not all of them. In particular, the fishing trolling patterns can only be initiated from a control head and not from Axiom. For sailing vessels some of the steer-to-wind angle functionality is also only accessible from a pilot controller. For all the basics though, the Axiom does a great job. You can lock the pilot and steer to a heading, track to a single waypoint, or follow a route all from Axiom. The +10/-10 you see on Axiom isn't part of the p70R controller because you have the rotary knob instead. You can simply give the knob a twist at any time to adjust the course. One click of the know is equal to 1-degree of change. The pushbutton 10 and 5-degree increments are a take-away from the pushbutton actuated pilot controllers, the p70 and p70S.
@kellylyon9174
6 ай бұрын
Hello! Where can I obtain an owners manual for Axiom, Lighthouse version 3?
@RaymarineInc
6 ай бұрын
Hello Kelly. LightHouse 3 manuals for Axiom are available online here: raymarine.app.box.com/s/rvhycb6x1brzo64921k5tsqwv2ica3j6/folder/199835371463 We generally issue a new handbook with each software release. In that folder you'll see quite a few past versions. If you're not sure which version of LightHouse 3 your system is at touch on Home...Settings...and the software version is reported on that first tab.
@andyjamesable
5 ай бұрын
Can anyone advise me .. I can’t find anywhere on the autoroute information that’s gives distance to destination .. they give time to destination etc or distance to next waypoint which with hundreds of little waypoints is pretty useless .. anyone have a reply for me .. many thanks
@RaymarineInc
5 ай бұрын
Hello Andy. Believe it or not, distance to final destination is a new addition to the data library on Axiom. Please update your software to the latest version (LightHouse 4.6) and you will find it in there. In the data menu where you can select items for databoxes, overlays, etc. it is in the Navigation category as "Distance to Go." This piece of live information has not been available until now.
@user-qb5vc4gn9w
5 ай бұрын
When I download Navion on my cell phone, how do I pair my cell phone with the axiom screen?
@RaymarineInc
5 ай бұрын
On your Axiom go to Home...Settings...This Display and scroll down to the Wi-Fi Sharing section. There you can setup the Wi-Fi hotspot in Axiom to make it visible to your phone. Touch the Configure button next to Wi-Fi Settings and there you can set the network name (SSID) and password. Next, go to your phone's Wi-Fi settings and connect to the network you just created. Once connected, launch the Navionics app on your device. It will detect that it is connected to Axiom and prompt about syncing data and updating charts.
@KMT15
3 жыл бұрын
What’s the shortcut for bringing full brightness back, after having it dim the night before? I remember seeing it on one of these videos but can’t seem to find it.
@RaymarineInc
3 жыл бұрын
On Axiom, Axiom+ and Axiom XL, swipe the power key left to right repeatedly. After the 2nd swipe the backlight starts increasing in 10% increments with each swipe. On Axiom Pro tap the power button repeatedly.
@MrTrapper28
Жыл бұрын
Where do I find tidal info on an Axiom 9? In particular tidal curves. I am running Lighthouse 4 and a Raymarine chart of Western Europe. Cheers Bob
@RaymarineInc
Жыл бұрын
Hello Bob. The easiest way to see tide heights and current speed is to turn on "Tides" mode in your chartplotter app. Open the chart and go to Menu...Mode...Tides. In this mode some of the chart details are temporarily hidden, but the tide and current stations become much more prevalent. Each tide station will show a graph with the current hight of the tide at that location. Current stations will show an arrow for the direction of flow, along with the current speed. There are animation controls along the top and bottom of the screen you can use to see how things will play out over time. There is also a button where you can specify a particular date in the future if you are planning for an upcoming voyage. You can exit out of Tides mode at anytime by going back to Menu...Mode...Navigate. You can also see tide and current information while in the standard navigation chart. Long-press on the chart in the area you want to search. From the popup menu select More Options....Find Nearest....Tides. The system will return a list of nearby tide stations sorted from closest to farthest. Touch on any station to see the details and graph.
@MrTrapper28
Жыл бұрын
@@RaymarineInc thanks for the reply. We can find the list of tide stations and when we press on one of these ‘for further info’ we get a window which shows sunrise and sunset times, and a message saying fetching data, but nothing further comes in/appears . This window stays blank. If we long hold on boat icon and turn on tide button it shows direction of tidal flow and strength but we really need full tidal curves info.
@MrTrapper28
Жыл бұрын
@@RaymarineInc Thanks for the answer. in addition to my previous reply, when I originally put the Lighthouse (preloaded) SD card in do I need to activate it anywhere? Its working as far as Navigational map reading etc but not pulling any tidal info in when you click on a tidal area in the listings, ie Falmouth (my local port). All I am getting is a box showing sunrise and sunset but no tidal curves. What am I doing wrong? thanks in advance for your help, much appreciated. Bob.
@jasonfiore6582
3 жыл бұрын
Thanks for taking these questions! Can you tell me why my display lags /freezes for several seconds on my axiom pro when I pinch/zoom? Happens quite a bit. What can I do to remedy? Apologies if question already asked. Thank you! And so very much enjoy this forum. So helpful!
@RaymarineInc
3 жыл бұрын
Hi Jason. Normally they are pretty speedy, so I am not sure why you'd be seeing a lag. Do make sure that your display has the latest software installed. As of right now that is Lighthouse 3.13 Edgartown. If it keeps doing that, definitely drop a ticket in our help system over at raymarine.custhelp.com and our team can help troubleshoot the issue with you.
@jasonfiore6582
3 жыл бұрын
@@RaymarineInc thank you very much for the speedy reply! Love your products and your streaming live info sessions along with customer service! Unparalleled!!
@garyengelman7867
11 ай бұрын
If i had 2 waypoinr a long distance away from each other, say on the ocean, 600 hundred miles apart and made a route from them, would that route ba a great circle route?
@RaymarineInc
11 ай бұрын
Routes at long distances like that appear to be great circle routes, but I would like to confirm that for you. I'll try to answer you here but please also send me an email to james.mcgowan@raymarine.com so I can be sure to get the answer to you.
@RaymarineInc
11 ай бұрын
Confirmed. Technically, all routes plotted into your chartplotter and navigated by GPS are treated as great-circle routes. At short distances you won't see the difference in the plot, or any discernible difference in the length of the route. On route legs at significant distances, you can see them plotted as great circles on the chart display when zoomed out.
@garyengelman7867
11 ай бұрын
Thanks so much@@RaymarineInc
@xavpil2
Жыл бұрын
What is the latest software for Axiom 9? I can’t find any update on the RM website
@RaymarineInc
11 ай бұрын
As of today (18 September 2023) the latest version is 4.5.84. This was released in the last 7 days. You can find it on Raymarine.com here: www.raymarine.com/en-us/download/lighthouse-4-update-for-axiom-chartplotters
@johnkropa2319
2 жыл бұрын
I have a new Axiom Pro 9 S. It came with Navionics charts, however It shows Lighthouse Charts as a choice in the chart menu. I thought it came with Lighthouse charts pre-loaded, however when I select Lighthouse charts, the chart screen has absolutely no detail as if the Lighthouse charts are not really loaded. How can I use the Lighthouse charts?
@RaymarineInc
2 жыл бұрын
Hello John. All of the charts on our system currently are read from microSD card media. There is a base-map for LightHouse Charts that shows a basic coastal outline, but its not suitable for Navigation. LightHouse Charts can be purchased from your Raymarine dealer on a card if you want to use them in addition to Navionics.
@johnkropa2319
2 жыл бұрын
@@RaymarineInc Thank you very much for your quick reply.
@jackschoer6597
2 жыл бұрын
Have you or can you talk about recording, saving, exporting and importing tracks and how to convert a track to a route. Thanks
@RaymarineInc
2 жыл бұрын
Thanks for watching the show, Jack! Take a look at this past episode on working with waypoints, routes and tracks. I think you'll find what you are looking for in here: kzitem.info/news/bejne/2ZmA0WWgkmp2oZg
@jackschoer6597
2 жыл бұрын
@@RaymarineInc I watched the video and it talks about transfering routes through wifi, but it didn't talk about transfering tracks (from the Navionics app to the Axiom 12) through wifi. Can that be done? Thanks
@eddiequiles1926
10 ай бұрын
Hello Jim, I have a Axiom Pro that has a red track that I can't get rid of. TIA
@RaymarineInc
10 ай бұрын
You can get into the track library by going to Home...My Data...Tracks. All of the recorded tracks should be visible there, and you have the option to hide or delete it. If that doesn't seem to get rid of it, please snap me a photo of what you are seeing on your display and email it to me at james.mcgowan@raymarine.com. I should be able to identify what it is and how to turn it off.
@eddiequiles1926
9 ай бұрын
@RaymarineInc Hello Jim, I've tired to email you and the email you sent me but it keeps bouncing back as undeliverable , Where can I sent the pics of the Red track I can't get rid of..TIA
@PeterNielsen5
Жыл бұрын
Hi Do you have or plan to do some basic Axiom sailboat laylines/ tack how-to?
@RaymarineInc
Жыл бұрын
Hello Peter. Yes, I would like to cover this in an upcoming episode.
@PeterNielsen5
Жыл бұрын
@@RaymarineIncPerfect, I’ll be looking forward to that. Thanks
@mikedunphy3338
2 жыл бұрын
How do I load the Navionics maps rather than the standard maps?
@RaymarineInc
2 жыл бұрын
Hi Mike. Navionics charts come on microSD memory cards and are plugged into the card reader on your Axiom. You the select them in Axiom's Chart app by touching Menu....Settings....and selecting the chart title on the Cartography tab. If your Axiom model has more than one card reader, or you have more than one Axiom networked together, it is possible to use more than one type of map at the same time, as mapping is shared between units.
@timgurr1876
3 жыл бұрын
I'm looking for a fish finder for a 2019 Princecraft Ventura 224. Who can I talk with for help in choosing a Raymarine model? Thanks.
@RaymarineInc
3 жыл бұрын
Hello Tim. Feel free to send me an email to james.f.mcgowan@raymarine.com. I would be happy to tell you about all the options and I can also help you find a local equipment dealer too.
@russseff1246
3 жыл бұрын
Hi gents. Anyone else having an issue with the axiom pro 12 rvx dropping a waypoint that you're actively tracking to on auto pilot or while manually steering? Its been happening to me fairly frequently
@RaymarineInc
3 жыл бұрын
Hi Russ. What is the connection between your Axiom Pro and your autopilot? Are you using SeaTalk NG or NMEA2000, or is is being converted to Seatalk 1 or even NMEA0183? If you can give us some more details on your system we can help you troubleshoot it. I suggest opening a ticket with the details over at raymarine.custhelp.com and our team can take a look. It could be something as simple as the waypoint arrival alarm radius being set too large, or a software bug.
@s.e.covingtonco3232
3 жыл бұрын
I have a Raymarine MDF ES 128 and use C-Map 4 D card - how do i go in and change my boat details - draft height and beam
@RaymarineInc
3 жыл бұрын
Hello Sir. On your LightHouse 2 eS128 you'll want to go into the Boat Details menu to setup your minimum safe depth, beam and height. From the home screen touch the CUSTOMIZE menu and you'll see the Boat Details menu where you can enter them.
@gavjones1636
2 жыл бұрын
Hi does the axiom have the option to do search patterns such as parallel track, creeping ? Thanks
@RaymarineInc
2 жыл бұрын
Yes it does. In your chartplotter app touch on Menu...New...Search Pattern and you'll see options for Sector, Expanding Square, Creeping Line and Parallel Line searches. Each one has a setup wizard to help you dial in the center of the search point, start and stop timers to determine set and drift, and configure the pattern overall.
@jeffh9288
3 жыл бұрын
Hey Jim I recently added data cable to get Yamaha engine data (non command link) to my Axiom in particular fuel burn. That being said data shows up in engine dashboard but not the fuel data I need. It does show up in fuel and trip settings in my data main settings page. So my question is is there anyway to move say just GPH and put that data say to my chart page. Thanks again for all the good info you provide This Raymarine live filled in that hole that was left when they stopped the Ray Forum. Jeff
@RaymarineInc
3 жыл бұрын
Hi Jeff. You should be able to add GPH to any page either as a floating data item, or you can add it to the swipe-out sidebar. To add a floating data item press Menu....Settings....and select the Page Settings tab. Touch on Edit Data Overlays, then Add. The data library is displayed. I think the value you want is in the Fuel category. You can long-press and then resize the item and move it wherever you want it to sit.
@jerryk2682
3 ай бұрын
How do I get SOG on my screen and not on the pullout ?
@RaymarineInc
3 ай бұрын
Hi Jerry. Each individual page on Axiom can have 4 floating data items. The data items can be moved anywhere on screen and resized for best fit and visibility. Its also important to note that each page's floating data items are unique and they are configured on a per-page basis. This allows you to show different items on different pages. For example you might want to see water temperature on your fish finder, but not on your radar. The process to add a floating data item is the same regardless of the page. Touch Menu...Settings...Page Settings and then select Edit Data Overlays. The screen will be slightly greyed out, and at the top will be buttons for Add... and Done. Touch Add. The menu that appears is the data manager. Data is categorized into groups to make it easier to find. Since Speed Over Ground comes from your GPS receiver, touch the group called GPS...and inside there, at the bottom, will be Speed over Ground (SOG). Touch to add it to the screen. Now, touch and drag it to move it wherever you want it to sit. If you tap it briefly, a menu pops up with options to Edit, Move, Resize or Delete. Touch Resize, and choose what size you prefer. You can drag it with your finger if you need to adjust where it sits after resizing to fine-tune things. When you are happy, either press ADD to add another item to the screen, or DONE to save and exit.
@Propman203
3 жыл бұрын
I’m in niantic ct can I meet your guy who has his boat in the river would really enjoy more information about this system
@RaymarineInc
3 жыл бұрын
Hi John. Send me an email to james.f.mcgowan@raymarine.com and I will see what I can do.
@jwmcconomy
2 жыл бұрын
hey jim, please remind me how to set up automatic "find ship" return on axiom. thanks!
@RaymarineInc
2 жыл бұрын
Hi John. Open the chart app and go to Menu....Settings....Advanced and you'll see a toggle button for "Auto Find Ship." Turn it on and that chart window will use that automatic function. You have the option of switching it on or off on each individual instance of the chart.
Пікірлер: 303