Where in the EFff is this place. And why is he not my neighbor?!?! 😂
@BeautyBeastRC
Жыл бұрын
Get you some proline mashers or proline mx57. Really nice on the xrt! great video bro.
@jeffreypadmos567
3 ай бұрын
What is the maximum speed that you got with this setup?
@SubdivisionNZ
Жыл бұрын
Dam that 800kv motor pulls hard that's epic. How many tooth pinion and spur you running man?
@MorrisKustomz
Жыл бұрын
38t pinion and 46t spur
@SubdivisionNZ
Жыл бұрын
@@MorrisKustomz thanks, enjoy your rig it’s a beast.
@francodimaggio7475
Жыл бұрын
@@MorrisKustomzmph provala sulla aspalto va più veloce
@Facts-R-Real
6 ай бұрын
I’d run 12s!
@nickhathaway4617
Жыл бұрын
1100kv I think is better a little lighter and fast as hell
@RCRolla
Жыл бұрын
Should we try it in another XRT?!
@BeautyBeastRC
Жыл бұрын
I came to post this too haha. 800kv is nice for sure but its heavier and easier to gear the 1100kv as well. I bet it runs cooler than the 1100 though.
@MaxvoltageRc
Жыл бұрын
Yea 1100kv is where it’s at
@nobody617
11 ай бұрын
Even the 1100 is almost to much. Hard to keep front end down. You can change center diff fluids change punch and throttle settings. The new 1275kv is probably the way to go. The higher the kv the higher the rpm. The higher the rpm the better for air control. I'm just use to the xo-1 speeds so I like the front tires down and accelerating super fast. Like a rocket. It's all good though. You got the wrong spot, but the other car to get that's different than this but super fast is the losi super Baja Rey. Scale driving is a lot of fun. Its suspension is so plush. My favorite cars I drive most are the xrt, dbxle and super Baja Rey You are all set there with the xrt, but seriously think about an Asuga. It floats bike a butterfly. With that big field I'd be wanting a high speed set up. Like 70+ mph at least. The xrt kicks ass and no need for anything else but sledge would be awesome there. I like the big cars though. Watch a bashing Asuga video. The thing is pretty cool. That dang super Baja Rey is awesome.
@giopirmisashvili5514
7 ай бұрын
❤❤❤
@Andy-sg3yv
Жыл бұрын
Any problems with the diffs/driveshafts with this motor and gearing ? Thanks in advance!
@RCRolla
Жыл бұрын
So we did shred the stock pinion but they are cheap and simple. As for bearings, we blow a few out bombing big jumps. Stock tires go quick if you like to go fast. Wheels crack too for that matter but it is my top 3 fav!
@Andy-sg3yv
Жыл бұрын
Thanks for the reply! I will definitely run hardened pinion/spur. Trying to decide between the 800kv or 1100 kv and the proline mashers vs the dboots backflips. Want the diffs/drivetrain to hold up. Any opinion on these options? Thanks again
@Andy-sg3yv
Жыл бұрын
Thanks for the reply! I will definitely run hardened pinion/spur. Trying to decide between the 800kv or 1100 kv and the proline mashers vs the dboots backflips. Want the diffs/drivetrain to hold up. Any opinion on these options? Thanks again
@nobody617
11 ай бұрын
I made a comment about the flower shirt, but i deleted it. I am a good boy.
@mattmaclearn263
Жыл бұрын
Gotta get them gennisiss foamless rc tires. Only thing is they start at 150 a pair
Пікірлер: 22