Great timing, this video series is just what I need. My engine is the next thing on the restoration block
@mbmpablo3631
3 жыл бұрын
Me too. 😉👌🏽 i have no idea where to go to tebuild my L134, im in LA
@kiffer289
4 жыл бұрын
That's a good block you have there Lew
@geoben427
4 жыл бұрын
Lots of great information. Thanks for taking the time to explain. Looking forward to following the process.
@bondvagabond42
Жыл бұрын
I like to use machinist "way oil" to hose out the swarf and junk out of the oil passages. It's basically designed to float all those sharp bits of metal out of the super tight bearing surfaces in in a machine tool, so might work well for junk packed in those hard to reach places. I am a machinist, and I find casting sand in 50+ year old engines all the time, from when they were just little baby engines, hah.
@diggs123456
4 жыл бұрын
Wealth of knowledge right there!
@willysmb7514
2 жыл бұрын
Awesome, I am going to be rebuilding mine this year. This helped a lot! Greetings from Alaska!
@hummernutsfl
2 жыл бұрын
Cool. Glad to help! We need support for the IFFC in Alaska. Alaska patrol! facebook.com/groups/1641202336209808/?ref=share
@rickey5353
Жыл бұрын
Just curious. What was your cost estimate?
@conceptalfa
2 жыл бұрын
👍 👍👍!!! Thanks for sharing!!!
@billbrisson
2 жыл бұрын
thanks for posting, looking forward to rebuilding my L134 (s) this winter
@Dane_Schroff
3 жыл бұрын
Looks like a RMCxxxxx number above the water pump. Wouldn’t that make it a M38 motor? Anyway, great video, very informative. Thank you.
@rakin5649
2 жыл бұрын
I know that you did this quite a while ago but that's an M-38 block as indicated by the serial number, not a CJ block. It's also a late version of that block as well.
@josuee.villavicencio3314
Жыл бұрын
Mine have serial number in the same spot but start with the letter and number 1MB following of five numbers (23***), what engine is that make that?
@pauldusharm6968
2 жыл бұрын
I'm watching this and thinking the oil pump is for an engine with a timing chain. The pump end has red on it, and I believe the sprocket is correct for timing chain. I just had my chain driven apart and sprocket is the same. Am I wrong?
@leinadalan
2 жыл бұрын
Nice! Question, how do you know what piston goes in what bore? My machinist fits each piston to its bore making them a mated pair. Rarely will you order pistons and have them be all the same size. I've seen pistons very in size .002 + Nice work!
@hummernutsfl
2 жыл бұрын
My pistons can vary in OD just a tad but are always mid range of the spec. The important thing is to get the ring gap correct. If one hole had to be bored over size bigger than the others, that size as well as the others will be stamped in the top of the piston and on the block. I have all my running gear like pistons, rods, crank etc all balanced. My guy is cheap so I go for it. Others charge alot so may not be worth it.
@conceptalfa
2 жыл бұрын
What about dipping the whole bare block into an ultra sound bath? Should clean it pretty well, shouldn't it? I mean even the passages.....
@hummernutsfl
2 жыл бұрын
I would still rod the passages out. The vibe may break loose gunk but it won't wash it out.
@conceptalfa
2 жыл бұрын
@@hummernutsfl you're right👍
@olivedrabgarage6243
4 жыл бұрын
Lew..the main bearing caps...would it be a good indicator that the cast numbers on them have the base facing the rear of the block as an orientation? Are they usually marked with a matching number like your diff carrier bearing caps are?
@hummernutsfl
4 жыл бұрын
Hmmm? I never looked at that. I always mark them to keep them correct. I'll take a look next time.
@olivedrabgarage6243
4 жыл бұрын
@@hummernutsfl that'd be great because all my caps were removed when I bought the blocks....they weren't bolted in but sitting loose.
@IronSharpensIron127
3 жыл бұрын
I was wondering how much would you charge someone to rebuild this engine? I wish I could rebuild mine myself, but I'm a disabled vet. I don't want to get ripped off when I pay to have it done.
@hummernutsfl
3 жыл бұрын
Where do you live?
@IronSharpensIron127
3 жыл бұрын
@@hummernutsfl I live in Arizona sir.
@hummernutsfl
3 жыл бұрын
@@IronSharpensIron127 darn. I love teaching guys how to do it. Not very difficult, really. Just attention to detail and being super clean. The factory book is really good.
@philipjohnson986
3 жыл бұрын
Where are you in CO I’m in Windsor and looking for good machining
@hummernutsfl
3 жыл бұрын
i am in Lafayette.
@kaerudinkosim3406
Жыл бұрын
May i get parts ones sir, pistons and others to select using
@hummernutsfl
Жыл бұрын
I get most of my parts here: www.rfjp.com/default.aspx?
@kumsuk77777
Жыл бұрын
What is the usual life of a quality engine rebuild such as yours?
@hummernutsfl
Жыл бұрын
I imagine one will get about 100k if maintained. Those old motors do not last as long as modern stuff but they do well for the technology. They are a low rpm, low compression motor so the bearings last a long time. The down side is the long stroke causes more ring and piston wear so they slowly become oval shaped. Takes a inside micrometer to measure the cylinders but that is why a hone job is a waste.
@kumsuk77777
Жыл бұрын
Thanks. As I recall the older engines often needed a valve job before pistons and rings
@hummernutsfl
Жыл бұрын
@@kumsuk77777 yup, valves ground and maybe new guides.
Пікірлер: 38