Very well done! Now I'm less anxious about tackling my two non-firing Porter Cables.
@TheTrullGallery
3 ай бұрын
Thanks! Just take it one o-ring at a time. Piece of cake!
@joealibrandi
2 ай бұрын
I have this stapler NS and the tension pin that allows for the staple housing to open disappeared. As a result the gun is now jammed. I have been able to find a pin that will work but I need to know how to stack the latch and pin back in place. The proper arrangement is imperative to gun operation. Please help do you have a film that shows how this is done Mr Joe 88yrs young
@TheTrullGallery
2 ай бұрын
@joealibrandi Sorry Joe, I don't. Have you checked the Porter Cable website? Sometimes, the parts diagram helps, too.
@davidecasassa8679
3 ай бұрын
Succinctly and clearly explained. Your remark about a "missing" part gave me some hope. I have a new, unused (apparently) Metabo pinner that I got cheap in an auction, which must have a manufacturing defect, as it leaks massively out the exhaust as soon as it is connected to the air supply. Depressing the trigger stops the leak until it's released again. I'm hoping it's a part missing or damaged on assembly, and not a casting defect.
@TheTrullGallery
3 ай бұрын
@davidecasassa8679 get a rebuild kit! I'd replace all of the o-rings and such, but it sounds like it might be in the trigger mechanism (those parts should be in the kit). Good luck!
@craig156
4 ай бұрын
What was that amber colored ring for on table.
@TheTrullGallery
4 ай бұрын
The amber ring was the old ring and it was replaced with the clear ring you can see early in the video. If memory serves, it goes up near the collar at the top of the piston. ...I think.
@craig156
4 ай бұрын
@@TheTrullGallery thanks that’s the one I need for my porter cable BN125
@2Jeezuzisreal
10 ай бұрын
I have an old mini stapler that won't work. Model 2118/29. Probably 20 years old my guess. Has been sitting for 4 years unused. Now it just makes a little pup pup noise when I pull the trigger and it has no safety mechanism Because it was made that way. I opened it up to be sure there was oil lubrication and wiped it out but it's not working. I have googled this particular gun but no repair information. Anybody have any idea what I can do ?
@TheTrullGallery
9 ай бұрын
Sounds like a bad o-ring in there somewhere. The trick is figuring out which one. Then you just need to find a replacement...
@antonioolivares4281
7 ай бұрын
Good vid. Looking for kit for Cambell Hausfield HDN104 nailer. Any help would be appreciated
@TheTrullGallery
7 ай бұрын
Try ereplacementparts.com.
@manuelgonzales4187
5 ай бұрын
I thought you did an excellent job, explaining the smallest details and what to look forward to when I begin my rebuilding of my pneumatic gun. I have three of them by the way.👍🏽👍🏽🙏🏽
@TheTrullGallery
5 ай бұрын
Cool, I hope I helped to keep 'em going!
@marisaldierna4285
Жыл бұрын
Hola
@ALLA1228
Жыл бұрын
You mentioned many detail no one else had noticed , thank you . I rebuilt a senco finish nailer and replaced the only broken part ( that 3 had identified as the culprit and upon disassembly I found it was broken ) however upon reassembly I cannot get my gun to fire , , thanks for your video it was thorough and concise , ,well done sir and thank you
@TheTrullGallery
Жыл бұрын
Thanks! And here I thought I was just rebuilding my gun. 😎
Пікірлер: 18