Shameless plug to check out my original songs on my music channnel ➡ kzitem.info/rock/AYFaKe31NSCMnIS-FQ4zxg
@S13_Sender
Жыл бұрын
Just finished successfully rebuilding my T56 thanks to you…. I wouldn’t have attempted it if this video wasn’t so well made to guide me through.. thank you for teaching me and saving me money. Well done
@TheBudgetMindedMotorist
Жыл бұрын
Thank you! It means a lot to me to know that my videos are helping people! 🙂👍
@Alexwaltman850
Жыл бұрын
Pro tip. Take the skip shift solinoid out and put your index finger through it for grip while your thumb hold down the lever with detent as you slide the case on. Makes installing the case infinity easier
@TheBudgetMindedMotorist
Жыл бұрын
Wish I'd thought of that! Thanks for sharing!
@lag1791
2 жыл бұрын
Just want to say your video helped me a lot with my own rebuild. My t56 is a bit different than your since it is out of a 2006 z06 vette but internally they are simular except mine came with a one pc countershaft. I totally mirrored the way you worked on the transmission. I took it one step further and covered a 6ft folding table with cardboard and shadow boxed and labeled every part, and wrote notes next to the parts that identified how it came apart. My 5/6 drive gear also came off by hand and I sent my mainshaft to TX Drivetrain performance. They due a spray weld and re-machine for$100 plus shipping. My rebuild was a bit more expensive than your since my goal was to fix my reverse syncro, that was almost gone, and do a full stage 2 upgrade that will hold the +600hp I'm making. Again, thanks for the time and effort on your video.
@headported
3 ай бұрын
best best video on rebuilding t56's thanks
@mubashircheentavida
2 жыл бұрын
Just put my rebuilt trans in, so far running good for the past 2 days. Thanks to this vid! Shipping was the biggest pain point of the whole process, and having keys fall out 2-3 times while trying to put the shift forks and main shaft together was annoying but I figured out how to hold it properly lol. For shimming, I talked to Texas Drivetrain Performance and they told me a method to shim without using a dial indicator and just based on feel.
@TheBudgetMindedMotorist
2 жыл бұрын
That's so awesome! I'm glad to hear this video helped! 🤘😁
@ChevelleMike71
6 ай бұрын
Enjoyed the two videos. A potential customer recently contacted me about rebuilding his T56. Told him I needed to “research” them a little bit. The research is watching someone else build one to see if I’ve got the proper tooling. 😂
@ZaskarPL
2 жыл бұрын
This is really great video, especially this 2nd part with assembly because on YT is missing this fully detailed video and manual is not so precise. I'll have to do the same with my transmission... now thanks to this video I think that I will make it very easy. Great job, thanks a lot!!!!
@TheBudgetMindedMotorist
2 жыл бұрын
Thank you!
@kylejaques1078
2 жыл бұрын
On the 5/6 snap ring the manual says to install it opposite of what you have done. Great video by the way! I can’t believe this doesn’t have more views! This series is the best T56 how to on KZitem. Nice job.
@TheBudgetMindedMotorist
2 жыл бұрын
Hopefully mine holds together then lol. Thank you!
@philsnow3784
9 ай бұрын
Thanks these 2 videos have been very helpful I just bought a t56 6speed manual gearbox but in pretty bad condition in need of a complete rebuild so I'm going to make my own video just to make it easy for me to remember the reassembly even though I have an excellent memory well better than most people
@brandoncastelloe7882
7 ай бұрын
Thanks for the video. Great job! I just finished up my refresh. I was glad to see the comment that it was shifting fine after a few thousand miles. Great detail! I wouldn't have attempted this without a solid video and this one was exactly what I needed.
@jasons250r
4 ай бұрын
Thanks for the great video. I found that putting it in fifth gear kept everything in place while putting on housing. Just my 2 cents
@davidstrait3973
Жыл бұрын
Hey, man! I know it's a year old, but it's helping me this weekend. I appreciate the detail and thoroughness that went into your video. Thanks!
@mubashircheentavida
2 жыл бұрын
I guarantee this series will be the most watched on your channel, the other rebuild videos hide like 80% of the work lol. I swapped a f-body t56 into my b-body and trying to be budget I went with a used one, put it in the car and find reverse was gone. At that point I just wanted the car running and ended up paying a lot more than I should have to get it fixed. Like 2 months later I feel like I wasn't able to get into 3rd gear without resistance and some just odd behaviors that I wasn't feeling before. For me to go the magnum route is so much more money, but at the same time if I pay for the labor to get this one fixed I will spend just as much as I would if I just resold it and bought the magnum. Which leaves one option, to rebuild it myself. Plan is within the next two weeks do a tear down and inspection, see what needs to be replaced and order it up. Do need to buy a hydraulic press and some snap ring pliers.
@BeastMR2
2 жыл бұрын
How did the rebuild go?
@mubashircheentavida
2 жыл бұрын
@@BeastMR2Great man. Ended up doing a stage 2 build and it's been solid in the few months I've been driving it. Actually rebuilding another one I picked for cheap. Just the confidence in taking apart your transmission when it has issues feels good.
@nickmellon6677
Жыл бұрын
I would guess the worn out synchronizer teeth are from either a leaking clutch slave or worn out master. When my master was bad it would work perfect and then go to the floor after a high RPM pull and cause my to grind the next gear. Great video!!! Very valuable information you can't find anywhere else. Makes me want to rebuild my T56 this winter
@TheBudgetMindedMotorist
Жыл бұрын
Thank you, I'm glad you like it. I agree, worn or week clutch hydraulics would definitely lead to synchro damage and wear. A lot of my car's history is unknown as I picked it up with 200k miles, but past clutch issues certainly could have contributed to what's in the video.
@jessicallewellyn4517
10 ай бұрын
Compared to Subaru your RTV job is a masterpiece.. but seriously i think we all put a bit too much rtv on, nobody wants to do it twice lol
@tattoosbyjoe216
10 ай бұрын
Great video
@BooneGT2k2
2 жыл бұрын
Great series! 10/10 rtv skills. Who am I kidding. Goop the perimeter, send it, and clean up later
@TheBudgetMindedMotorist
2 жыл бұрын
Thanks! 😁👍
@wayne007nz
2 жыл бұрын
i have a few photos of rail linkage interlocks (46min) but cant post in comments, Great videos by the way.
@flux_core_fx
Жыл бұрын
Very helpful video, thanks so much!
@AshleysBlissfulCreations
2 жыл бұрын
you are so detailed! amazing work!
@TheBudgetMindedMotorist
2 жыл бұрын
Thank you so much!
@TheHotSauceGT350
8 ай бұрын
I think once my T56 leaves the shop if it needs a rebuild i may end up doing this my self.
@jasonmason9686
Жыл бұрын
Also bless you for this video sir. Well done, tip of the hat, and a bravo :)
@TheBudgetMindedMotorist
Жыл бұрын
Thank you! 😁👍
@jasonmason9686
Жыл бұрын
9.9 on the rtv and reading the instructions. Gotta let it flash over then finish tightening. I usually go 24 hrs. Also i use the special rtv for automatic transmissions by permatex #81180 since the trans takes mercon 5 i think. Might go with amsoil tho.
@AngelHernandez-ex7ji
2 жыл бұрын
The balls you have attempt this is unfathomable
@TheBudgetMindedMotorist
2 жыл бұрын
😆 it was pretty intimidating, but also one of the more fun projects I've gotten to do. Took some courage yes, but mostly I'm just to cheap to pay someone else to do things... 😆
@AngelHernandez-ex7ji
2 жыл бұрын
@@TheBudgetMindedMotorist 😂 I'm usually the same but somethings I just leave alone. You definitely sound like you did your homework. Nice work, I Definitely enjoyed the video!
@mubashircheentavida
2 жыл бұрын
Hmm re-watching from 1:07:00 to 1:08:00 ish I noticed that the washer you put after 6th gear on the counter shaft extension looks like part #115, but in the manual and in your dissassembly video that washer sits on the top of the 6th gear needle bearing.
@TheBudgetMindedMotorist
2 жыл бұрын
😳 are you sure it wasn't part 108? I suppose it's possible I could have gotten 115 and 108 mixed up, but I can't tell for sure in the video. So far everything feels fine regarding 6th so I'll see what happens I suppose.
@mubashircheentavida
2 жыл бұрын
@@TheBudgetMindedMotorist Yea it's probably fine tbh. I picked up disassembled t56 for cheap and practicing how to shim that one and so far it's pretty straight forward. My first one has been running great also since I installed it, went a bit crazy with the stage 2 kit since I was already down money due to an incompetent shop.
@TheBudgetMindedMotorist
2 жыл бұрын
@@mubashircheentavida sounds like you'll be a pro in no time! Are the shim kits in stock anywhere now?
@mubashircheentavida
2 жыл бұрын
@@TheBudgetMindedMotorist yea I actually got a set from thegearbox. Though the amount of shims I gotta say were not much lol
@TransAm4ever
Жыл бұрын
I do think that the #115 spacer was not in the right position before the 6th gear needle bearing. looking at the wear pattern of the bearing inside my the 6th gear race, its not in the same position without the #115 spacer. Which is not a huge deal, but means the bearing will ride in a different position. The thrust washer #108 was left on the counter shaft during disassembly and reassembly videos. So anyone watching this video, don't forget that washer like I did. Luckily I caught it early. These videos helped a lot.
@KNS_Racing
6 ай бұрын
what bearings need to be replaced to resolve the common issue of 4th gear popping out when the transmission goes in and out of being under load? everything I read said this is from a worn bearing in the trans that causes 4th to pop out
@Xrc53
2 жыл бұрын
I really wish you would have brought the camera closer when you were talking about the reverse and sixth gear shaft to show everyone how you lined up the pin for everything (46:00-47:50).
@ChrisSullivan69
2 жыл бұрын
Great video. Hows it shifting now that its back in the car? Im hoping I dont have to do any shimming on mine since I cant find shims anywhere either!
@TheBudgetMindedMotorist
2 жыл бұрын
Thank you! It's been a few thousand miles now and it's shifting just like it should.
@BadAzpPerformance
Ай бұрын
Aftervyou install the main case and 6th gear are the output and 5/6 shaft supposed to spin?
@kennedywong9854
Жыл бұрын
I broke guide pin on my t56 and how gonna remove now?
@red666A
Жыл бұрын
What's the part number for the tail shalf seal?
@huglferdr
2 жыл бұрын
Keen to know where I can order the counter shaft extension for 5 and 6 gear. I have a Holden VE SS with the T56 6speed manual. Reason being ive lost 5th & 6th gear, but still have reverse. The gears lock in 5 & 6 just doesn't engage. Its as if it were in neutral. Just Revs out. Any help or information would be good. Thanks
@TheBudgetMindedMotorist
2 жыл бұрын
I haven't been able to find anyone who makes new replacement counter shaft extensions. Sometimes there are used ones available on eBay. It's possible the splines for the 5/6 cluster sheared from the main shaft. If that's the case a new main shaft should be easier to find.
@huglferdr
2 жыл бұрын
Ok that is very helpful information, I will look around on ebay for used. I think you are right might have to look at getting a main shaft. Thanks for the info dude much appreciated.
@IH84CL
Жыл бұрын
Try mal wood (our tremec importer) for parts
@erniesdeck7550
2 жыл бұрын
Great video I watched both parts and I feel like I learned a lot I have a 95 T/A with the T56. I don't know if this is normal or not but when I get going from a dead stop in first gear especially if I'm still at very low RPM I would say like 1300-1400 for a quick second it makes this sound like rocks in a can of coffee being shaking up. I used to have an 87 T/A with a T5 and it did the same exact thing. All my forward gears feel great! The only other issue is once in a while it'll pop out of reverse. The car only has 84,000 original miles I purchased it from the original owner and older gentleman who always garage kept it, How close am I to needing a rebuild would you say?
@TheBudgetMindedMotorist
2 жыл бұрын
Thank you. That's awesome finding a 95 with so few miles! Mine makes quite a bit of noise at low rpm as well. Rattles like crazy at 1k-1200 RPM or so. I've seen a lot of forum posts describing the same thing so from what I know, it's pretty common. As long as it's smooth going into gear I wouldn't worry a whole lot about the noise. Popping out of reverse is kind of a bummer but mine did that for a while before I finally got sick of it. popping out will eventually wear the sychro slider and gear, but it might be ok for a while as long as it isn't happening super often.
@punk86
2 жыл бұрын
Great video. Too bad you didn't bead bast the case. Idk I'm weird like that lol
@TheBudgetMindedMotorist
2 жыл бұрын
Thanks for watching! Bead blasting leaves em looking good for sure!
@natethekidd2905
Жыл бұрын
Did you check and reshim the trans?
@JaimeLopez-lg2cm
Жыл бұрын
Hey man my car got stuck in 3rd any ideas and how much did you spend in parts
@TheBudgetMindedMotorist
Жыл бұрын
I believe being stuck in gear usually means broken shift keys within the synchro assembly. All in for parts I spent about $600 if I remember right. Was expecting to spend closer to $300 but replacing 2nd gear and the synchro sliders added up to more. I also used stock style parts so it would have been a little more if I used billet keys and such.
@JaimeLopez-lg2cm
Жыл бұрын
@@TheBudgetMindedMotorist thanx man I'm start taking my tranny apart this weekend 🤞
Пікірлер: 64