I usually cut the nails out and replace them with 1-1/2" drywall screws. It's a lot easier to install them that way. And if you make a mistake you can simply buzz the screws out with your screwgun instead of having to pry the nails out with a flat bar.
@charlesjohnson6073
4 жыл бұрын
Hey I've been an apprentice for almost 2 years now and I just want to let you know that I watch your videos every day on the way to work and I've learned a lot from you and really enjoy what your doing. Keep up the good work.
@jessesantana8408
4 жыл бұрын
As a carpenter helper I've had owners change there mind and tell me to move these while I'm putting up finish ceilings I'm grateful when people leave that extra loop of cable saves us both time. Wonderful tip
@strangerofthe2067
4 жыл бұрын
Your technique for nailing up a can to one side, then sliding it over to the other side to nail up is perfect for what you described for keeping it centered and lining it up with other cans. I’ve had quite a few apprentices over the years and some just have a hard time understanding that technique for some reason. They just wanna hammer it up and then end up with wonky legs and a row of zigzagging cans lol. Get your measurements on both studs, line up to one side and nail down, slide it to the other side to line up there and nail down, then get your measurements in the middle of the bay, just like you showed in the video. Lasers are great too, especially in older homes being remodeled where nothing is square. Anyway, great video! I appreciate the channel! One other thing, me personally, if I ever have wide stud bays where the legs are stretched out pretty far, I wrap some electrical tape around the middle of the legs where they meet just to help prevent them from sagging or possibly breaking, just a little extra step to help keep them in place.
@jacobmillyard6799
4 жыл бұрын
Worth noting another quick and easy tip is to go half your spacing distance off the wall I.e. if your going 6' on center try to start and end 3' off the wall or end of the run. It will make the light look even with the reflectance
@robertwelch9647
3 жыл бұрын
Hearing and reading other electricians opinions is awesome. Learn something new everyday.
@terrell1470
Жыл бұрын
Great tips...I've learned most of these the hard way, through trail and error...before KZitem, but what gives me a hard way to go is making the brackets fit between the joists after cutting them shorter. Most manufactures put breaks every couple of inches, but trying to put the brackets back together after carefully cutting them is sometimes a problem.
@footballstar124
4 жыл бұрын
I would like to see a video on writing and reading circuit diagrams and schematics. My current teacher low key kinda sucks and I've been able to firmly grasp everything you explain. So it would be wildly helpful. Keep up the good work!
@AngelTorres-tk2nw
4 жыл бұрын
Go to the near Ocupensional center, Or go to the Contractor's state license Schools and study for the C10 license.
@seansmythe7543
4 жыл бұрын
And then how to put the schematic diagrams into the field! How many conductors will I need?
@jeremynguyen2346
2 жыл бұрын
@@AngelTorres-tk2nw what is Dustin doing
@jeremynguyen2346
2 жыл бұрын
@@AngelTorres-tk2nw what is a recessed can
@Alex-qp8zz
4 жыл бұрын
We'll throw a drywall screw in between the tabs and the arm to keep it in place. And leaving a loop is always good when doing custom, as it seems builders are always moving can layouts like you said. Nice video. Pretty common sense to most resi guys, but for a homeowner or new apprentice this video could be real helpful!
@chrisbrangan9304
4 жыл бұрын
Straight to the point, awesome detail on the visual aids, and very clear instruction. Best demonstration videos I've seen in a long time. Awesome job Brother...
@distant2001
3 жыл бұрын
Lots of good info for us "non-electricians." Much appreciated!
@dpgsmith
4 жыл бұрын
Excellent, well-explained, practical and thoughtful video. Thank you for taking the time to produce this. Very much appreciated.
@roberttrinkle5188
4 жыл бұрын
Jam up job brother. Exactly how I’ve always done my cans and lasers are a must for today
@mike.3727
4 жыл бұрын
This video had so many helpful tips. Small stuff these experienced guys learned that just amazes me. Love having a reason to do something, and doing it right. Awesome stuff brother
@simoncooper3734
2 жыл бұрын
Great video . Thank you!
@RB-xv4si
4 жыл бұрын
One very important thing to mention is that you need to be aware if the can is insulation contact (IC) rated. If it’s not, and you stick it up in a ceiling with insulation, the fixture can overheat, start a fire, and you’re getting your ass sued when the Fire Marshall finds out. Just a thought 😊
@mr.g937
3 жыл бұрын
Why would they ever make a can thats not IC-rated
@RB-xv4si
3 жыл бұрын
@@mr.g937 non-IC cans are cheaper.
@timbo86051
3 жыл бұрын
@@mr.g937 they do make them that way.
@erikkarling2176
2 жыл бұрын
@@mr.g937 If they are being used in a downstairs ceiling, like a kitchen. There isn't any insulation in the ceiling joist between floors, just in the upstairs ceiling. Those would be IC rated.
@jeremynguyen2346
2 жыл бұрын
@@mr.g937 what is Dustin doing
@hadjipando853
4 жыл бұрын
This video was awesome, really helpful. I would recommend maybe getting some drywall screws instead of using the nails. I’ve discovered the nails are super cheap and get bent out of shape very easily. Also if you need to move the can and take it all the way down, trying to pry the nails out, make the tabs all crooked and jacked up, it’s just not fun, makes it a lot harder than it needs to be. With the screw it’s an easy install and take apart if need be. Also the laser was a great idea. I personally use a chalk line, but anything you can use to make sure you have a solid straight line.
@kylelikeskjvbible
4 жыл бұрын
You're the best Dustin, keep up the good work
@PatrickKQ4HBD
4 жыл бұрын
9:00 Lighting design is something I know almost nothing about. Thanks for illuminating the subject! 👍
@willkincaid5841
3 жыл бұрын
The flat or half inch led are what we have been installing in some cases and I love them. Granted they cost more! But you can just pop them out and adjust the Kelvin setting. simple and easy to work on.
@wesleytweed
2 жыл бұрын
Dude, THANK YOU
@michaelcollette8170
4 жыл бұрын
I like the look of the flat LED lights more and they're easier to install hahaa
@vandoo66
3 жыл бұрын
I sell Electrical products and NOBODY buys cans anymore
@brianpayers
2 жыл бұрын
How do you install those without a ceiling though? If all you have are the trusses, isn't a can light necessary?
@heroknaderi
3 жыл бұрын
Do a video about regular cans vs shallow cans. I enjoyed the video 😎
@j.m.castillo9561
2 ай бұрын
Maybe a demonstration on how to deconstruct an installed unit for wiring inspection or troubleshooting.
@nebraskaninkansas347
4 жыл бұрын
Didn't know if you would also go over IC vs Non IC rated as well. Of course I was renovating my house and the lights I had removed were Non IC rated. So they naturally decided to bury them in blown insulation. Glad it never burned my house down.
@wim0104
4 жыл бұрын
using *modern* LED bulbs helps a LOT! we've had to explain to engineers about old nineties LED tech being too hot... or why they should leave some air gap to help it vent (the can insert/sleeve being the wrong shape...).
@sparkydstoolboxtalk1024
4 жыл бұрын
Your explanation of why you don't strip too much insulation off the conductor, Is my explanation of why you should cut out the wagos and use wire nuts.
@wim0104
4 жыл бұрын
those wagos are a pain with AWG12.
@skiball83
4 жыл бұрын
I always cut them off too, i dont trust them.
@hmpz36911
4 жыл бұрын
Thorough and attentive to details.
@skiball83
4 жыл бұрын
Love it. I do it all the same way except for one thing. I know it takes longer, but I HATE wagos and I cut them all off and wire nut everything. Ive just seen them fail too many times to trust them.
@plebiansociety
3 жыл бұрын
Wagos aren't for stranded, other than that I've never seen a wago fail other than installer error (no waterproofing outside, wire not pushed in far enough) Even counting stranded wire failures I've seen maybe a dozen and a half in 15 years compared to bucket loads of wire nut failures.
@heuliseslopez4204
3 жыл бұрын
Thank you for making this video! It was very helpful and great tips ! 😎👍
@jakesully5402
3 жыл бұрын
Those cans bring back bad memories. I’m still going to electricians’ group twice a week for therapy from the last time I put in about 80 of those horrible things in someone’s house. It’s no wonder electricians drink so much
@TWA717
3 жыл бұрын
Loved the video Dustin and perfect timing for my bath remodel. I would love to see you do a video on installing and properly wiring cans and using low voltage dimmable light inserts above a tub/shower including any additional wet/damp area safety and dimming switch considerations that you would suggest. Loving the EU! Thanks for sharing...
@eldstgilmorbarboydodellatb4413
2 жыл бұрын
💚💚💚💚 bookmark/ notes : underground railway coal mine , bending the notches in notches like the fram bracket for over the range microwave installs ( a real old fashion metal popcorn bag ) …..ect…..tbc…..-g-b, bot
@CaseyGpdx
3 жыл бұрын
We just got some of these cans with the nail but above the thing that helps you put it on the right place isn’t totally flat
@Face2Face1987
4 жыл бұрын
Another great video man, thanks for explaining it so well and detailed. You're the GOAT. Cheers brother!
@postrockforthemind128
4 жыл бұрын
Lithonia wafers are great for old work. Even if there is a stud in the way. The wafer is literally 1/2in thick. I use them all the time with my company.
@trev6007
4 жыл бұрын
i agree all my company uses now is wafer style rec even for new work
@zacharybob4336
4 жыл бұрын
@@trev6007 Are you guys able to just leave a coil up in the ceiling and then cut in with a hole saw? I've been talking to my boss about doing this, worth the extra few bucks when you get it back in labor savings.
@justinandrade2299
4 жыл бұрын
So question, is Romex required to be stapled within 12" of the connector, or 12" of length of wire? As you were were showing examples, it was definitely more than a foot. That leads me to believe the code really means within 12 inches of its termination, in in that case, 12" of the can.
@jimmyjenkins5744
3 жыл бұрын
Within 12” of the device or termination
@justinandrade2299
3 жыл бұрын
@@jimmyjenkins5744 Well yes, but what if you (for some stupid reason) looped the cable up and down a bunch of times, close together using up, let's say 5 feet of cable? But the end of that mess is still within a foot of the connector. Theoretically I could still put it on the end of the mess no? Yes, I've stretched this WAY too much, but I just wanted to see if anybody had any clarification to the many "cloudy" codes we must follow. Do you know what I mean? 😔 Forgive me.
@joshd1472
4 жыл бұрын
we missed ya keep making these amazing videos
@Rairyujin
4 жыл бұрын
Im a 3rd year apprentice and I have alot of trouble tracing out control circuits (float switches, on delay, off delay etc) and would love a video on that.
@LEEPSTONES
2 жыл бұрын
Te amo! Nice vídeo
@oliverwhyxx6824
4 жыл бұрын
All we install now in quebec canada is low profile recessed light , good to see your videos tho !! 🤘
@skiball83
4 жыл бұрын
Those waffer lights are amazing in tight remodel spots. Especially basements with all the ducts and pipes run every which way.
@illestofdemall13
4 жыл бұрын
I also try to use them whenever possible but it depends what our customers want. The flat panel LEDs are easy to run, can be installed in almost any space, and consume very little wattage.
@paulzecchino1071
3 жыл бұрын
Thanks man, great explanation
@19993gt
4 жыл бұрын
Keep bringing the great content !
@Fret01
4 жыл бұрын
I like the idea about the laser.
@Mark-oc9ig
4 жыл бұрын
Thank you for the video in all of your knowledge
@jeffryt1434
4 жыл бұрын
awesome video as always, here in nyc it metal tracks/studs instead of wood lol
@AhmadEscobar
3 жыл бұрын
I did a resi side job once that was my one of my foreman’s side gigs and he supplied us all with the new construction recess cans for a remodel. Was the most pain in the ass job I’ve ever done
@jakesully5402
3 жыл бұрын
Yup. I used to get real hateful putting in those fucking recessed cans. I’m so glad the slim line ones were brought on the market
@Einzee
4 жыл бұрын
Absolutely correct about fancy people always changing their minds!
@stevencampos874
4 жыл бұрын
What laser are you using?
@avalianteffort40
2 жыл бұрын
I've got a truss down the centerline of my hallway putting a damper in my can plans. Trying to figure out a fix for this that doesn't involve those flat LED cans.
@AlexGarcia-vv4ux
4 жыл бұрын
Do you have a video on the laser or lasers you use if not can you ?
@walterdiaz2003
2 жыл бұрын
Can you use the light junction box to extend a third wire that has nothing to do with the the lights circuit?.
@sledge3003
4 жыл бұрын
Another great video......one caveat, when dealing with the adjustable legs wear gloves, they will quickly cut you!!!
@damianobelmonte2239
4 жыл бұрын
love your vids keep it up!
@chrisdoering4591
4 жыл бұрын
Electrician u what kind of lazer do you use in your video? I use DeWalt and it's really hard to see the line unless it's dark out.
@wim0104
4 жыл бұрын
maybe his camera made it look better than it is; digital cameras are essentially infrared sensors with color correction.
@brenthubner9521
3 жыл бұрын
replace the battery
@tittyrino
3 жыл бұрын
So many good tips I know the folks who are less advanced with doing these cans will take away a lot of useful information thank you for the video👍
@topherdevoe9500
4 жыл бұрын
You forgot to mention the difference between IC and TC cans. I definitely agree with leaving loops on everything, not just lights.
@willkincaid5841
3 жыл бұрын
Good vid though and informational.
@The42Joker
2 жыл бұрын
If you can use either the bigger knockouts or the smaller ones, which do you prefer to use?
@ElectricianU
2 жыл бұрын
Depends on the wire size, connectors for NM I have on hand or for the metal clad cable on hand.
@dannydominguez6815
2 жыл бұрын
Do you have a link to where you got that laser?
@zsmith125
4 жыл бұрын
"Having a reason that you're doing everything that you're doing is really important." Great wisdom right there, man. How many problems do we create for ourselves by just doing things without thinking about them first? Too many!
@rocker8692
4 жыл бұрын
Like your vids,good work.
@evanrocha5465
4 жыл бұрын
Great video man! Love your channels. The most informative that I’ve come across. And in trade work experience is so important so attention to detail is so key in learning. Thanks ALOT. Evan, from Boston,MA. I’m a Residential builder here.
@rozellescott2343
4 жыл бұрын
Hi this is Rozelle great video
@pedrogomez3168
3 жыл бұрын
Can you instal can lights without removing existing ceiling
@jerrymay3806
2 жыл бұрын
And what about insulation? Are they asking rated fr insulation..?
@jesuspadron7232
4 жыл бұрын
What kind of laser you use!? Any recommendations?
@alleviated1289
3 жыл бұрын
Milwaukee has some awesome M12 lasers they are pretty nice but I personally think Dewalt has the best laser but I think they’re best one is like $500 but if your looking for a great affordable laser try the M12 Dotted/line Milwaukee laser or the Bosch Line/laser they’re pretty good
@tylerrainville2533
4 жыл бұрын
The one thing I make sure I do with cans is measure 2-4 times each depending on the layout. Sounds like alot but recessed cans are one of those things I feel you really can't fuck the layout of up.
@jamalcole1985
4 жыл бұрын
Thanks for making this video. IBEW 595
@adamstanley8552
4 жыл бұрын
A lot of times I cut the juegos off and use wire nuts
@seansmythe7543
4 жыл бұрын
Adam Stanley paid by the hour eh? lol jk respect for making good connections
@skiball83
4 жыл бұрын
Same, i dont trust them.
@hanlee8150
4 жыл бұрын
Could you please tell me what laser that was being used?
@stephennewman5900
3 жыл бұрын
How many can lights can you install on a 20-amp dedicated circuit? How many on a 15-amp circuit?
@jahnelss
3 жыл бұрын
What is that device called that you used to line up the lights? And where can I get those?
@AM1015-
4 жыл бұрын
do an episode with LED cans, these are archaic nowadays
@bryanduchane2371
Жыл бұрын
LED's have changed recessed cans forever and for the better!!! It's almost impossible to find a can that isn't LED..... Thank God!!
@seansmythe7543
4 жыл бұрын
We screw our cans in instead of nailing so it’s easier to remove in case you fuck up or customer wants it moved
@KameraShy
3 жыл бұрын
Would it not make sense to check continuity of the entire installation after it is put up and before drywall?
@jakesully5402
3 жыл бұрын
Yes, it certainly would make sense, and it would be a “best practice”. The junction boxes are accessible, though, so any joint problems can be fixed even after the drywall is on.
@jeremynguyen2346
2 жыл бұрын
@@jakesully5402 what is Dustin Stelzer
@jamm6676
4 жыл бұрын
For some reason I always have issues putting up new construction can. 🤔
@andybaucom5319
3 жыл бұрын
I’m an Apprentice. I’m looking for the best material to read up on. Please help
@christheisen3571
2 жыл бұрын
Noone really explains how to trim the rails down to size. I cut one on the holes and it falls apart now wtf....
@wim0104
4 жыл бұрын
Fancy Lazor! Make & model#, please!
@Rooster000
4 жыл бұрын
where'd you get that lazer? i been looking for 1 with 3 lines haven't been able to find
@Niklaos
3 жыл бұрын
It looks like he is using the Bosch model, there is a Green and a Red version, they also have an optional receiver for situations where light level is just too low. Got mine on Amazon, extremely handy tool, I use mine all the time and I'm not even a Pro, just DIYing a whole house. www.amazon.com/s?k=Bosch+GLL3&i=industrial&ref=nb_sb_noss_2
@colinstu
4 жыл бұрын
"The most expensive cable run is the one that's an inch too short." Yep, definitely give yourself some extra!
@Dylan1094
4 жыл бұрын
What kind of laser
@mikeymiranda859
4 жыл бұрын
What about layout?
@s3tione
4 жыл бұрын
What is a "helper"? I've never heard of this before.
@lukesnyder3293
4 жыл бұрын
Like an apprentice
@eldstgilmorbarboydodellatb4413
2 жыл бұрын
💚🤘🏿
@weslawsonsilverback
4 жыл бұрын
I have a light similar this but it goes out every few minutes then comes back on. What seems to be the problem?
@lokoamerican4934
4 жыл бұрын
What type of bulb do you use? The cans have a heat type sensor built in. If your using halogen or incandescent it may be getting hot and and shutting off to cool. If its LED not to sure based off just that info.
@markborchers6447
4 жыл бұрын
Maybe a lose nuetral or bad bulb
@weslawsonsilverback
4 жыл бұрын
@@markborchers6447 where is the loose neutral located at? The panel box?
@weslawsonsilverback
4 жыл бұрын
@@lokoamerican4934 I use LED.
@derekstratford7937
4 жыл бұрын
Do you have it on a dimmer
@Triqkshot
3 жыл бұрын
Fuck using the nails on HH cans get a drywall screw and put it in that way. Quicker, easier to fix, and a lot less work. Track use a metal screw obviously
@jorgecruz3411
4 жыл бұрын
Question why are you using 12/2 Wouldn’t you use 14/2 ?
@chevyman1130
4 жыл бұрын
All depends on the situation, due to arc fault breakers, most people put lights and plugs on same ciruit. Could still use a 15 amp ciruit, but I think it's best to use 20 amp to be on the safe side for vacuums etc, and keep in mind your not allowed to down size the wire.
@strangerofthe2067
4 жыл бұрын
Guy above me already answered, but it just depends on the size of the circuit. If you're adding to a 20A circuit, gotta use 12-2. I personally don't put lights and outlets on the same circuits anymore for the most part, I try and put outlets on 20A circuits and keep my lighting separate on 15A circuits, but in older construction of you're adding lights to an existing circuit, don't just assume it's a 15A circuit and use 14-2, always check the amps of the circuit before adding anything on it so you can use the correct size wires. 👍
@chevyman1130
4 жыл бұрын
@@strangerofthe2067 Yep, great response, however I'm curious on your method, on the arc fault breakers, if lights and plugs are on separate circuits, then that would mean a bedroom could have 2 arc fault breakers. I understand your combining several room lights together etc. And possibly plugs I'm just like know other peoples methods. Thanks man
@strangerofthe2067
4 жыл бұрын
mark 80 yes everything on arch faults that needs to be by code. Say for example, a small two bedroom house, I would likely put the two bedroom outlets on one circuit, the bedroom lights, along with maybe bathroom lights or something or maybe smoke detectors on one circuit, then probably kitchen and living lights on a circuit, living outlets on a circuit or maybe even with the bedroom outlets depending on how many there are, then kitchen outlet circuits to code, bath outlets, small appliances, etc. sometimes it’s overkill and not necessary, but I used to work for a company that wanted to do the bare minimum on everything, trying to do as few circuits as possible and really loading everything out to the max, and I just hate wiring that way. Creates problems for homeowners and I had to make a lot of trips back to houses after people moved in and had issues with breakers tripping all the time just because they were so loaded. Now I work for a company that is pretty much the exact opposite, all about quality over quantity and would rather put a bit more into material and time spent to do it right and so it allows me the freedom to wire basically how I would wire a home if it was mine. Nothing like tripping a breaker when you’re vacuuming at night and all your lights go out with it lol, then you have to fumble around in the dark. So that’s my method personally, I know some companies and some people would rather do bare minimum for cost and I get that, I did it that way for a long time, but now we try and just give quality work to people and have happy customers in the end, and it’s been working out great! Also kind of a house by house basis, I do a lot of high end custom houses for pretty wealthy people so they’d rather spend the extra money for overkill.
@chevyman1130
4 жыл бұрын
@@strangerofthe2067 Thanks man, but your right it does suck when the breaker trips and the lights go out as well, I hear that alot why people separate the 2. I personally now put each bedroom on it's on circuit. I just think its easier. However I service work now, 90% of my work is commercial, and bucket truck work, thank man for responding.
@markborchers6447
4 жыл бұрын
I slide the can legs all the way in when I cut them, cause sometimes you twist the ends and they are a pain to get back in
@wagner55
4 жыл бұрын
👍
@mnewt712
3 жыл бұрын
Gold nuggets
@benjaminpatton6785
2 жыл бұрын
Nvm found it
@ezraohnouna353
4 жыл бұрын
I Never trust the screws to hold the can moving I put some electrical tape in the corners
@seansmythe7543
4 жыл бұрын
Ezra Ohnouna Same, or fire a screw thru the legs and a part of the can
@ezraohnouna353
4 жыл бұрын
@@seansmythe7543 I have found that the screws losen pretty easily
@seansmythe7543
4 жыл бұрын
@@ezraohnouna353 super easily. Bump it with a bit of force and Now your lights off
@MikeWoodard
4 жыл бұрын
Hey do you dislike the wafers or just used the old ones for teaching And a reason I've been told to face junctions on the inside us because theoretically, you would run less wire being on the inside part instead of going around cans
@stevencampos874
4 жыл бұрын
Can you don’t track lights next?
@stevencampos874
4 жыл бұрын
*Do
@ajyhimst2782
3 жыл бұрын
wafer lights will make these obsolete eventually
@JuanIslands
4 жыл бұрын
I want to fight the guy who disliked this video
@thaitichi
4 жыл бұрын
Nobody uses these anymore. The modern flat led lights are what everyone uses now.
Пікірлер: 171