All of these guys did 15- 20 min videos,. Talking and even skipping steps. She does it in under 5.5 minutes and covers it all. YOU ROCK!!! SALUTE!
@DaruDhillon
2 жыл бұрын
Thanks so much! That's great to hear.
@Jackspaniel1
2 күн бұрын
Thank-you Daru. This video was perfect for what I am doing. Your demonstration was very easy to understand. I have one light to install in my bathroom and your video has helped me out greatly.
@tyneciawilliamsking
Жыл бұрын
Why can’t everyone make this as simple as you did? Subscribed, thank you!
@DaruDhillon
Жыл бұрын
You rock Tynecia! Go get ‘em. Thanks!
@vinnie9762
Жыл бұрын
How did the wires magically appear there. 😂. DIY’s is the reason I’m always busy. Thank you.
@dominoez21
Жыл бұрын
I also have this question. Where did the wires come from?
@edcastillo4456
Ай бұрын
I was looking for this comment as I thought the same. Conveniently located within an arm’s reach covered only by electrical tape.
@datsuntoyy
2 жыл бұрын
I just put 6 8" Halos in my Kitchen and 4 6" in the dining room. Both on dimmers. They are absolutely AWESOME!
@DaruDhillon
2 жыл бұрын
Great job, that’s awesome! Having dimmers in a dining room is a nice touch! 👍🏽
@datsuntoyy
2 жыл бұрын
@@DaruDhillon Tell my wife, she hates dimmers. lol I have them all over. Some on a hub controled by my phone.
@schenkkohain
Ай бұрын
So quick and to the point. What a breath of fresh air. I’ve seen too many long winded videos lately. 🙂↔️
@DaruDhillon
Ай бұрын
Glad you liked it!
@Yermove
2 жыл бұрын
Excellent video. I actually went to electrical school in the '70s but chose a different field to career. Things have changed since then. Connectors etc are "different" so I'm appreciative for these educational videos. Thank You!
@DaruDhillon
2 жыл бұрын
Thanks so much, it’s great to hear from you Yermove! I really like this style of connector. Wire nuts were invented in my hometown but they are easily misused. With your experience your installation will be an easy one. Hope you enjoy your lights and like them as much as I do! 👍🏽
@kenlam1051
Жыл бұрын
should have checked to see if there is any obstruction up in the ceiling (like a ceiling joist) before you drilled a 6 inch hole on your drywall
@DaruDhillon
Жыл бұрын
Good tip! Important to confirm that 1st! 👍🏽
@Natedz
3 жыл бұрын
I have never had that kind of luck, cutting holes and wires dropping down for me that easy😂 Good video though
@DaruDhillon
3 жыл бұрын
I removed the ceiling before running the wires. Most people won’t have that option. Next time I fish wires I’ll post. 😀
@marshahudgins3957
2 жыл бұрын
Damn...I thought I was the only one who'd question this lol. I'm needing this but was told my electrician would have to cut through the drywall if they can't access via attic.
@veroandariega
23 күн бұрын
Question: Anything else I need to do when there is insulation above the light? Thank you for your videos!
@DaruDhillon
22 күн бұрын
Double check that your light is good for an insulated ceiling. LED are low voltage, low heat so you should be good to go.
@veroandariega
22 күн бұрын
@@DaruDhillon I'm glad I saved the box and the instructions! Thank you so much!
@csgamble
Жыл бұрын
The junction box has two black tabs on it for the wire to enter the connection space. No need to pop the hole out and use extra parts to connect it.
@DaruDhillon
Жыл бұрын
Thanks Chris, that’s correct!
@mvsawyer
Жыл бұрын
Some of the boxes that come with these lights don't have the protector/strain relief already on them. If you've watched other wafer install videos, you'll notice most of them just remove the knockout and put the wires in. I was actually looking for videos that use the strain relief so I could find the right one to use and this is one of just two I found.
@chipcunningham6005
7 ай бұрын
Those lights look great. I have seen that some of those LED lights have adjustments for setting the power of the light (brighter etc)
@DaruDhillon
7 ай бұрын
Glad you think so, they’ve been great! You can adjust the color temperature on these. I like the warm light setting. There’s a lot you can do know with lighting and brightness is something important to keep in mind, thanks for that!
@jdtaxpayer801
2 жыл бұрын
This lady did a fabious job of explaining...very impressed.
@DaruDhillon
2 жыл бұрын
Thanks JD! Glad it helped. 👋
@cesar464747
3 жыл бұрын
On the side of the box dose black spots are connectors always good when your only connecting two wires. No need for the connector unless your jumping 3 lights on that . Use the stripper or flat of it's Eaton to use the included connector
Excellent explanation. Cheeful and to the point! She's a doll and makes it fun to watch.
@joeygriffith8977
Жыл бұрын
Great 👍 vid. What rule do you use when working off one lighting junction box in the room???🤔 How many lights can you connect together at one time? 🤔 Thanks!
@alexc2257
Жыл бұрын
Trying to figure this same thing out. I have a light fixture that I'd like to daisy chain recess lights off of.
@VanishIntoThinArt
10 ай бұрын
You made it so easy. Appreciate your presentation and the helpful tips.
@DaruDhillon
10 ай бұрын
Thanks for letting me know, that’s great to hear. It’s a rewarding and straightforward project. You’ve got this!
@filster1934
Жыл бұрын
Do not pry the knock-outs from the box, that’s what the two black plastic panels are for. Insert a screwdriver in the slot and pry the access panel up and away. Then slide your romex into the grippers. The romex is secured in place when the lid is snapped shut.
@DaruDhillon
Жыл бұрын
Absolutely you can do it that way and I appreciate you sharing your tips! I included the knockouts because a lot of people don’t know you need to use connectors and are doing it incorrectly.
@jamescourier1545
Жыл бұрын
Thanks for posting this. You explained the procedure very clearly, Daru. I got this! 🙂
@DaruDhillon
Жыл бұрын
Glad it was helpful James! 👍🏽
@snowwhite2709
5 ай бұрын
Ĝood explanation of most stuff, but where did the wires magically come from?
@DaruDhillon
5 ай бұрын
It was in a junction box during a renovation. I would explain that part now.
@trangbethke8812
Ай бұрын
Mine has been twitching, and I don't know why. Is it because of the voltage, or is the existing junction box going bad?
@KS-zq4hz
Жыл бұрын
Excellent 👍. BTW what brand of the LED lights are the best to install in a living room? Nice video, thank you.
@DaruDhillon
Жыл бұрын
Thanks KS! The brand is linked in the description. I find the top domestic brands are well made. 👍🏽
@MarkR973
Жыл бұрын
Thanks.... helpful! perhaps a little slower and closeup of connections next time? Thanks!!
@DaruDhillon
Жыл бұрын
Thanks for letting me know and for taking the time to comment! The feedback is appreciated so my latest wiring video is slower with more closeups thanks to suggestions like yours.
@delanceydiy
2 жыл бұрын
Exactly what I needed. Thank you.
@DaruDhillon
2 жыл бұрын
Happy to help DeLancey and thanks for watching!
@RealJoshBinder
2 жыл бұрын
Super helpful --- thanks!!
@DaruDhillon
2 жыл бұрын
Glad you found it useful Josh!
@kenyatahgriffin9706
Жыл бұрын
This was such a great video and soooo easy to follow. Thank YOU!
@DaruDhillon
Жыл бұрын
Thank YOU for watching! Appreciate it 💕
@CenfJ
4 ай бұрын
Amazing channel. So simple
@DaruDhillon
4 ай бұрын
Thanks! Welcome :)
@LCculater
Жыл бұрын
Wow great video , where were you when I needed you ? ❤
@DaruDhillon
Жыл бұрын
I’m here. If I can help you out let me know. Thanks ❤️
@pennyarizzio2824
5 ай бұрын
Is this box okay if the ceiling has insulation in it?
@jpthsd
Жыл бұрын
Thank you for the tips!! I like the reverse drilling tip! Also to prevent the drywall drilled dust, we should use some sort of cup folder over the drill head right? Thank you,,your video helps me feel more confidence to go do this by myself!
@DaruDhillon
Жыл бұрын
Probably the most important tip I would add is to wear a mask to protect your lungs from drywall dust. You can use an attachment to trap the dust if it’s a concern or you’re working in a finished home. It’s great to hear you’re building your confidence! Love that. 💪🏽
@Troblack
Жыл бұрын
How do you change one when it goes out??
@2Ryled
2 жыл бұрын
How can you know after drilling the hole, the wire is right there? I think that would be hit or miss.
@DaruDhillon
2 жыл бұрын
I ran the wire while the ceiling was down before I installed the drywall. That won’t be the situation for a lot of people. Next time I fish a line I’ll shoot a video on it. Thanks for the question! 👍🏽
@michaelnorcini2145
Жыл бұрын
Great video. One question. Can one light be controlled by two switches? I'm thinking of replacing the existing hall light with a recessed wafer light. The light can be controlled by two seperate switches.
@DaruDhillon
Жыл бұрын
Thanks Michael. Yes it can be controlled by two separate switches.
@EdsterL
Жыл бұрын
I have 6 of theses, I get everything except the wiring part, I'm little confused. I currently have one ceiling light in the center, I want to replace it with 6 LED's, my question is how to do I wire these? can I use the current wires assigned to the center light? then run another line to another LED, then on the second one run another line to 3rd LED etc....I've seen a lot of videos just want need more clarification? great video by the way, you did an amazing job 👍
@DaruDhillon
Жыл бұрын
If you are removing your ceiling light, you can use the wire from your ceiling light to wire your first recessed light then continue on to the next running a length of new wire to the next fixture. Follow your local electrical code but it sounds like your on the right track. Thanks Edster 👍🏽
@alexc2257
Жыл бұрын
How would I daisy chain this off of a light fixture? Would I connect a second Romex cable from the light fixture to the recess light? I'm assuming I can just twist the live Romex, light fixture, and new Romex (that will go into recessed lights) together?
@DaruDhillon
Жыл бұрын
Hi Alex, check that your power is off then feed the new wire from your light fixture into the junction box and make your connections.
@queentaj4704
2 жыл бұрын
Hello great video! I would like to know if you could use this fixture to replace a twist in light bulb fixture???? Thank you!!!
@DaruDhillon
2 жыл бұрын
Thanks! You can use this to replace an old ceiling light fixture. You would have to remove the old junction box, before installing. Good luck Queen Taj!
@ericreni2170
Жыл бұрын
Great job u made it easy for me.
@DaruDhillon
Жыл бұрын
Fantastic Eric! Thanks so much. Hope you like them!
@taika2
2 жыл бұрын
new sub here video helped me new home owner here…quick advice as an editor your video cuts are to fast.
@DaruDhillon
2 жыл бұрын
Thanks for letting me know Angel. I’m working on improving my editing. Appreciate the feedback and for subscribing!
@MrMike-mp8fw
2 жыл бұрын
So I’m new to wiring and a little scared. I know enough to be dangerous…. Which is is dangerous. So If I want to string 12 of these wafer lights together, what size wire am I running from junction box to junction box and I assuming it will have to be the heavy gauge white wire that you connected originally? Any chance you could do a video about that. This was very informative.
@DaruDhillon
2 жыл бұрын
Hi Mike, being cautious when wiring is always smart. Take your time and you’ll build confidence as your knowledge grows. I’m using a 14 gauge wire to connect all the lights in this home. I will be adding more wiring videos soon. Thanks for your support!
@jefferykorinko6861
2 жыл бұрын
Great video, tried watching others. Your video was the best!
@DaruDhillon
2 жыл бұрын
Great to hear Jeffery, thanks!
@jojojim91
9 ай бұрын
Excellent video!
@DaruDhillon
9 ай бұрын
Thank you very much!
@dmtom9619
Жыл бұрын
Great video. But I'm looking for a video that show how to remove the Wafer light without damaging the ceiling so that I can replace it with a ceiling fan. Thanks
@DaruDhillon
Жыл бұрын
Gently pull down the light with clean hands. Try to get your finger tips under the light to pry it away so you create a small gap.
@PeterSchneemann
8 күн бұрын
How do you take it off?
@jlee7063
2 жыл бұрын
That “too much pressure” upward punch was very freighting and suggestive…. Oh my 😲
@triciagiordano8243
Жыл бұрын
What if there was a junction box in the ceiling. Can you show how to take it out etc?
@abhisheknayak2411
2 жыл бұрын
Superb informative video no doubt. Whats cooler than that is your denim shirt ❤😎 Loved it !
@DaruDhillon
2 жыл бұрын
Thanks for the support Abhishek! ☺️
@user-pu3gq5vs1x
Жыл бұрын
Hello, Thanks for the instructions! Three of the eight ceiling LED lights turned off with no reason. I tested the LED lights, they work fine but there must be a problem in the wiring or in the J-Box. Do you think I should rewire or but a new J-Box to fix it?
@DaruDhillon
Жыл бұрын
The lights come with their own J-boxes. It’s good that you checked your wiring. If you feel it’s an issue with the light itself you can also contact the manufacturer. I hope you find a solution.
@ronforeman8394
2 жыл бұрын
thank you!! excellent and concise video for beginners
@DaruDhillon
2 жыл бұрын
Thanks so much Ron! Great to hear from you!
@latinovoice2224
Жыл бұрын
I only have two wires a black and white one what do I do with the extra copper wire?
@DaruDhillon
Жыл бұрын
Hi, Older homes will usually only have a black and white wire. In that case people will usually wire with the white and black and will not use the ground wire since they don't have one.
@chowchowkenobi9769
Жыл бұрын
@@DaruDhillon what do we do with the extra copper wire just leave it loos in the box,, i dont have ground wire coming from the ceiling either
@frankcampos1251
Жыл бұрын
Great video and explanation, thank you for sharing. Do you have a video showing more details on the wire snap connectors you used (instead of wire nuts). Specially a video that shows how one connects additional wires when “Daisy-chaining” additional recessed lights?
@DaruDhillon
Жыл бұрын
kzitem.info/news/bejne/14qj04SfpIx4lJw Here's a link that shows you close up how to use lever connectors. Good luck! I hope you like them as much as I do. 👍
@frankcampos1251
Жыл бұрын
@@DaruDhillon thank you so much for your quick reply. You are awesome!!
@DaruDhillon
Жыл бұрын
@@frankcampos1251 back at you Frank, cheers!
@johntaylor4870
2 жыл бұрын
Excellent video, thank you.
@DaruDhillon
2 жыл бұрын
Great to hear John, thanks for watching!
@joseluisemiliano
2 жыл бұрын
Wauoo excelente era justo lo que necesitaba ver, hay muchos videos muestran como instalan pero se quedan cortos.. este fue el más completo 👌👌
@DaruDhillon
2 жыл бұрын
Gracias Jose! 👋🏽
@alex-fm5bf
2 жыл бұрын
Very very good video, 👍 thanks
@DaruDhillon
2 жыл бұрын
My pleasure Alex, happy it helped! 😊
@d.m.4815
2 жыл бұрын
My dad has a very poor can light in his shower. Do you think this would hold up in the shower with the moisture?
@DaruDhillon
2 жыл бұрын
For shower lights you need to a light that says shower light or good for wet locations. Lithonia is a good brand that makes several sizes 4", 6", etc. Here's a link for thin wafer LED lights (like in the video). I love that you are helping and looking out your dad. Wet Location LED Light: amzn.to/3J5p9UE (Amazon affiliate link)
@keithrice9281
2 жыл бұрын
Just has a spare wire chillin up there?
@DaruDhillon
2 жыл бұрын
I ran the wire before I installed the drywall. When the joists were exposed. Not everyone will have that option. 😎
@chowchowkenobi9769
Жыл бұрын
what if i have no ground wire coming from ceiling?
@DaruDhillon
Жыл бұрын
Older homes often have only two wires, white and black. You’d wire those as usual since you don’t have a ground wire.
@nelstadel9185
Жыл бұрын
How do I know if I have wires like that in the ceiling?
@CME_876
2 жыл бұрын
How would you install that if you have a decking ceiling or a concrete ceiling???
@greg925911
2 жыл бұрын
So can you cut off the twist connector of that light and just connect it to a 12 Volt system
@Jimmy-qy6gk
2 жыл бұрын
Thank You!! Great educational video 👍
@DaruDhillon
2 жыл бұрын
Great to hear Jimmy, thanks for watching!
@kryptik0
2 жыл бұрын
Yes, the wire just conveniently popped out where she needed it to be. If only things were that simple.
@DaruDhillon
2 жыл бұрын
I gutted the house and ran my wires before I installed the ceiling. I primarily do large scale renovations but the next time I have to fish a wire I’ll do a video on it! 👍🏽
@MissMoyston
11 ай бұрын
Did you do this video yet? I want to put niches in my hallway wall with mini recess lights. I have an outlet in that wall and need to know how to create a switch and wiring for the lights. Help please
@markgiblin8213
2 жыл бұрын
What size romex connectors did you use and are they available on Amazon?
@DaruDhillon
2 жыл бұрын
Hi Mark, I have a link in the description box for the Romex connectors on Amazon. They are 1/2" plastic push-in which I prefer. They have been out of stock on Amazon for awhile, so I have also included a link for 1/2" Romex metal connectors which are in stock for metal boxes. That one just needs to be screwed into place. Both work well and will protect your knockouts. Good luck with your project! Your local hardware store may have better stock in store right now. Thanks.
@jasonfuessel2961
Жыл бұрын
Did you use a 4 3/16 hole saw or 4 1/4? Your link amazon link take me to a 4 1/4 hole saw.
@roxpar1816
2 жыл бұрын
Really great video, to the point and informative. 👍
@DaruDhillon
2 жыл бұрын
Thanks so much Rox! 👋🏽
@Toastcook1212
2 жыл бұрын
@@DaruDhillon :) great DIY vid
@DaruDhillon
2 жыл бұрын
@@Toastcook1212 Glad you found it helpful! 👍🏽
@ronfirnrohr5655
2 жыл бұрын
If I caught it right, those lights seem to have a color selector. The color selector should be set to the desired color prior to the box going in the ceiling. Arguably, someone unfamiliar with these lights might think there is a problem with lights if they purchased one that had been changed as a result of an open box/returned item.
@DaruDhillon
2 жыл бұрын
Hi Ron, Yes good eye. I seemed to have set the lights and forgot to mention that in the video. Sorry. Thanks for pointing that out. As Ron said, please select your color temperature before putting your wafer light in your ceiling.
@whitefroglegs32
Жыл бұрын
Does the 6" of wire in a J box requirement not apply to these light boxes?
@DaruDhillon
Жыл бұрын
I would follow the same rule for these junction boxes.
@organicvids
Жыл бұрын
107 hey how do you have clean hair without sheetrock dust? I wanna know. Haaaaa great vid and attitude.
@DaruDhillon
Жыл бұрын
It’s magic. Thanks Malach211!
@christinah7716
Жыл бұрын
She was not wearing a mask and inhaled the sheetrock dust, preventing it from falling into her hair.
@DaruDhillon
Жыл бұрын
@@christinah7716 it’s best to wear a mask and protect your lungs.
@jeffreyspence2510
Жыл бұрын
Your smile is so much more radiant than the light you installed.
@DaruDhillon
Жыл бұрын
Thank-you kindly Jeffrey ☺️
@bradbrownlee8489
Жыл бұрын
Just curious, but why was there a hot inaccessible electrical wire above the ceiling. In my world, that violates code.
@DaruDhillon
Жыл бұрын
Everywhere that would violate code. It's illegal to have a hidden inaccessible live wire anywhere in your home, including hidden junction boxes. Thanks for posting it's important to know a live wire was never sitting in the ceiling.
@amrunner4
3 жыл бұрын
When you put the connection box back up in the ceiling, and assuming it id IC rated, is it OK that fiberglass insulation batting completely covers the box? or do I need to make an opening in the batting so that it can "breathe?" The boxes do not get hot from what I understand.
@frantzmommy
2 жыл бұрын
Hi Daru. Thanks for the great guide. I had a reno down with several of these installed, a few months ago. One of the wafers is now flickering. Why would this happen? Installed by electrician. Only 1 is flickering. Is this something I can fix myself or do you think I need an electrician to come back out?
@DaruDhillon
2 жыл бұрын
Often a single flickering light is the result of a loose connection. I would turn off the breaker. Test that power is off with a voltage tester and open up the junction box. Once opened check that the black and white wires are firmly connected. Push in your connectors again to confirm they are secure. After doing this I would turn the power on to see if the light is working properly. Then I would turn the power off and push the wires carefully back into the junction box. Place the closed box back into the ceiling and reinstall the wafer light. Sometimes people mistakenly shove wires into the box - this can cause a loose connection. If you feel comfortable doing that it’s not a difficult process. If you don’t your electrician should come back and fix it. Any good electrician will come back to fix their work free of charge. I’d start with calling your electrician. I hope that helps Kimberly!
@DaruDhillon
2 жыл бұрын
Good luck it’s always nice if it’s an easy fix!
@Wilem35
3 жыл бұрын
How do I get the magic wires at each lamp location?
@DaruDhillon
3 жыл бұрын
Hi Wilem35, that would be helpful, for sure. I ran the wire before drywalling that part of the ceiling while the joists were accessible. Next time I fish electrical, I’ll make a video. Thanks for letting me know!
@manueljfrancisco5480
10 ай бұрын
Good. Job😎
@ebayseller6040
5 ай бұрын
3:59 pretty sure you are supposed to put the wires through the black plastic part of the box.......
@poogie_bear
2 жыл бұрын
I would like to install only 1 wafer light. Would I still need a junction box, or can I wire it directly?
@DaruDhillon
Жыл бұрын
The junction box comes with the light.
@TheHawksFlock
Жыл бұрын
Tip- Put an ice cream bucket over the saw to collect the dust
@DaruDhillon
Жыл бұрын
Excellent! That’s a money saving tip that is so helpful. Thanks! The idea of reusing what you have is so much better than buying something you’ll use once. A+
@aasmith78
Жыл бұрын
Cut horizontally with your knife across the insulation instead of down the middle. That’s day 1 electrical helper stuff.
@DaruDhillon
Жыл бұрын
Thanks for your helpful tip!
@shensuohao
3 жыл бұрын
Why did you go in reverse while drilling?
@DaruDhillon
3 жыл бұрын
It’s easier to drill in reverse, plus it’s safer so you can avoid cutting any wires in your ceiling. Subscribe for more tips to help with your DIY projects. Thanks for the great question!
@anthonytauber9209
2 жыл бұрын
Can anyone recommend a dimmer switch for infibrite dimmable canless led lights that wont cause buzzing?
7 ай бұрын
I know you posted a year ago but Lumitron I find works best. Make sure the lights are compatible however with a dimmer switch.
@Asmitty4lifeGaming
Жыл бұрын
What kind of laser level did you use?
@DaruDhillon
Жыл бұрын
I have a Dewalt laser level it does the trick. 👍🏽
@abusarhanmohammad2036
2 жыл бұрын
👍👍
@wch4972
Жыл бұрын
I guess nowadays the junction box is much smaller
@brianeells1920
2 жыл бұрын
The wire can clip in the side of the box. No need for a connector.
@DaruDhillon
2 жыл бұрын
That's true Brian, thanks for pointing that out. Lots of people are using unprotected knockouts on KZitem so I wanted to make it clear that it's dangerous. Thanks for the reminder👍
@donnah3892
2 жыл бұрын
Where Did you get the wire from?
@DaruDhillon
2 жыл бұрын
Hi Donna, The wire was from an old ceiling light in a junction box during my rough in inspection. Next time I have to fish a wire through drywall I'll post a video! I used Resilient Channel on these ceilings which won’t be applicable for most people who are fishing wire.
@donnah3892
2 жыл бұрын
@@DaruDhillon I hope you do 1st time I've seen your channel 👍
@kevyncole4519
2 жыл бұрын
Great video darlin......but if I viewed correctly while drinking my titos vodka this morning I noticed that the Halo can already had connectors preinstalled in those junction blocks already.......but I do like the * buttholes" you installed better!great job and keep up the good work!
@DaruDhillon
2 жыл бұрын
You’re spot on, you can use them! I’ve only ever used the Romex connectors because that’s what the electricians I work with use. They allow more room to make your connections when wiring multiple lights. The highest ranked DIY video is wired without them. Wires through raw metal which is a major fire hazard. It’s a my version of a public service announcement. :) I want everyone to wire safely. Good to hear from you Kevyn! You made me laugh!
@brandoncole6358
2 жыл бұрын
@@DaruDhillon please excuse my dad he's turning 50 next year and has early onset dementia. XD
@kevyncole4519
2 жыл бұрын
That's next month son.....lol...maybe you can install some cans for my old man dementia cave!😆
@devyncole7435
2 жыл бұрын
@@kevyncole4519 dad do we need to start looking at homes for you.
@kevyncole4519
2 жыл бұрын
I'm sorry ...for a 50 year old dementia ridden or titos induced dad....I commented on your post....lol....as a retired electrician am happy however that both of my electrician sons commented on this post!!!🤪🤪🤪🤪I hope I brought other people to laughter in these dark times❤️❤️❤️
@benzun9600
2 жыл бұрын
Nice. But I hate LeD lights bad for eyes
@lanceellis5910
Жыл бұрын
Please for the love, hold your hands steady. Otherwise, helpful video.
@DaruDhillon
Жыл бұрын
Thanks Lance! Appreciate your feedback.
@juan6810
9 ай бұрын
No need to pop out the metal plugs the box comes with 2 pre installed black connectors Good video though
@DaruDhillon
9 ай бұрын
Thanks for that information! It’s true. I always go for the knockouts. I should have been a boxer.
@DaruDhillon
3 жыл бұрын
Thanks for watching and subscribing! A reminder to select your color temperature before installing in your ceiling. LED 4" HALO: (in video) amzn.to/3tIgv6R LED 6" HALO: amzn.to/37imgij (Amazon Affiliate Links) If you make a purchase a small fee will go to this channel at no cost to you. Ceiling Light Replacement Upgrade | What 98% Don't Know: kzitem.info/news/bejne/14qj04SfpIx4lJw
@jayman3573
2 жыл бұрын
You can’t change it after it’s clipped in?
@DaruDhillon
2 жыл бұрын
@@jayman3573 lights like this have the color temperature selection on the junction box. If you have a bigger budget smart lights are installed in the same way but you can adjust the colors and color temperature with your phone.
@jayman3573
2 жыл бұрын
@@DaruDhillon but you can’t do that with these type of lights?
@DaruDhillon
2 жыл бұрын
@@jayman3573 correct!
@jayman3573
2 жыл бұрын
@@DaruDhillon this product sucks then! 🤕
@thomasj2972
3 жыл бұрын
You dont even need a connector, you can bring wire thru those black slits
@DaruDhillon
3 жыл бұрын
Thanks Thomas! That’s true. I wanted to run the wires that way because some DIY videos feature wiring through unprotected knockouts which is a major fire hazard. But it’s a good reminder to have it here too. Thanks!
@javimelendez414
2 жыл бұрын
Your statement about a series connection is incorrect.
@DaruDhillon
2 жыл бұрын
You can use the other knockouts if you wish.
@wolfmangoland7972
Жыл бұрын
Artificial Intelligence will not take over these jobs
@DaruDhillon
Жыл бұрын
Always good to learn hands on applied skills. It’s rewarding to DIY! 🙌🏽
@lizardman1303
27 күн бұрын
Their just a random loose wire their . U didn’t need to go to the attic .
@DaruDhillon
27 күн бұрын
@@lizardman1303 I had the ceiling replaced so I ran it from a junction box. I would show that step now.
@DanielSilva-ct1gd
3 жыл бұрын
Hi can you please do a video request of you Installing a led troffer fixture led fluorescent tube please ? Please reply back to my comments when you get a chance thank you,!!
@DaruDhillon
3 жыл бұрын
Hi Daniel, Thanks for the suggestion. I'll be making more videos on LED lighting. I'll keep your suggestion in mind if the opportunity comes up to install one!
@DanielSilva-ct1gd
3 жыл бұрын
@@DaruDhillon Hi thank you so much for replying back to my comments and letting me know I appreciate it thank you !! Can't wait for your next light bulb 💡💡 videos I'm so excited !!
@edwarddemedeiros3607
8 ай бұрын
A convenient unattached LIVE electrical wire just lying on the ceiling? Seriously?
@DaruDhillon
8 ай бұрын
It was in a junction box. The house was under renovation. Thanks for your feedback.
@pjdn
Жыл бұрын
KZitem is trying to compete with TikTok...
@DaruDhillon
Жыл бұрын
I hear you.
@myballsitchsomethingfierce6319
2 жыл бұрын
Never grab live wires even if they insulated all it takes is one tiny hole for the electricity to past through. I made the mistake and I'm typing this from Hell.
@DaruDhillon
2 жыл бұрын
I hope you are feeling better. Thank you for taking the time to share your experience to help others.
@kennixox262
7 ай бұрын
Homeowners may like the excess brightness but smart people hire lighting designers to create an excellent lighting scheme. You want replaceable lamps not an integrated fixture that you have to replace the whole fixture. LED's don't last nearly as long as advertised. I get it, you are paid to peddle this crap.
@DaruDhillon
7 ай бұрын
DIYers are a smart group and kind. I appreciate their support.
@kennixox262
7 ай бұрын
I disagree. Smart, yes. Trained in design, probably not and that is how you get ugly flipped houses. @@DaruDhillon
@pjdn
Жыл бұрын
Nothing new here. You don't have to make another video of the installation. There already are several posted. Maybe you just want to be on camera.
@DaruDhillon
Жыл бұрын
I’m always listening to viewer and subscriber feedback. It’s important to me and I appreciate their suggestions. Grateful for that!
@pjdn
Жыл бұрын
@@DaruDhillon okay great. Try to keep face out of camera view frame. It’s so annoying. As if you just discovered teeth whitening or something.
Пікірлер: 214